At first i thought you weren't going to show the installation of that G clip, but then you showed how it went on the other side of wrist pin And thats was all that was needed to make this episode complete Nice video Kalispell Thanks for that photo of going to the sun road . I love and miss Montana. Thanks mike, much love home skillet...❤️💛💚
@MikesMiniMotors9 ай бұрын
Thanks, Charles! The first time I watched that back when editting, I had a mini panic attack 😵, until I seen the second one. I meant to add a caption during the first one says to watch the second, and forgot... Oops! I'm glad you like the GNC photo!
@ridesliknacho49849 ай бұрын
Excellent video, I rebuilt mine last winter down to the crank (not big bore kit) and wish I had this video then! Getting the timing aligned was the biggest pain. That said, I have a small oil leak at the cylinder base gasket so I get to do it all over again in a month. 😂 Looking forward to the ride videos!
@MikesMiniMotors9 ай бұрын
Thanks! Sorry to hear about your base gasket!
@ChrissScooterSupportGroup8 ай бұрын
Great video! I have a bunch of scooters and am thinning the herd right now, but think I will keep an eye out for a c3 to do this and the transmission kit on. Looks like a fun project and thanks for taking the time to document.
@MikesMiniMotors8 ай бұрын
Thanks! If you can find a C3, I would recommend picking it up! They’re a blast!💥
@turbotoshy9 ай бұрын
Yoooo! Binge watched all of your Yamaha C3 videos last night and was sad to see no new uploads in a while! Awesome you are back. Picked up a Giggle here in the UK, so been good to see what can be done, and how the whole scoot goes together! Keep it up man.
@turbotoshy9 ай бұрын
Also, did you design that radiator cover? Looks great!
@MikesMiniMotors9 ай бұрын
Thanks! Life got busy for a bit, but I'm not gone!
@MikesMiniMotors9 ай бұрын
Yeah, thanks! I designed and 3D printed it.
@swampe_rat9 ай бұрын
Great video, Mike!
@MikesMiniMotors9 ай бұрын
Thanks! Glad you liked it!
@kidwilson33579 ай бұрын
Awesome video.
@MikesMiniMotors9 ай бұрын
Thanks!
@thelagmeister9 ай бұрын
Great video as always. It's an interesting design with those little rods moving the valves. The numbers after the kit look great considering the Yamaha 125cc I just sold did 40mph at 15 seconds and topped out just above 50 mph.
@MikesMiniMotors9 ай бұрын
Thanks! I can’t wait to tune it better and get even more out of it!
@spencerguignet12109 ай бұрын
Cant wait to hot rod my C3!
@MikesMiniMotors9 ай бұрын
You’ll love it!
@spencerguignet12108 ай бұрын
@@MikesMiniMotors what is the solution for the coolant temp sensor? the stock sensor bottoms out in the casting...
@MikesMiniMotors8 ай бұрын
I had to drill into the head through the sensor hole a little bit for clearance. Just be really careful, take your time and don’t drill too deep!
@spencerguignet12108 ай бұрын
@@MikesMiniMotors i ground down the tip slightly and went to far, it bleeds coolant thru the body of the sensor now lol. i ordered another, im going to try to shim it out with 2 or three of the sealing washers if it seals. Ill let you knowhow it goes. Thanks!
@spencerguignet12106 ай бұрын
follow up , i double gasketed the CTS, that gave enough room to clear the casting. I wasnt able to use the turning specs you posted however. I have a +25% setting on most rpm ranges with good results. Once the weather breaks a bit more, ill have my wideband on it and dial it in.
@GucciSoup3 ай бұрын
Mike, you're a legend for making these! What was the 0-30 with the big bore? Looks like 7ish seconds?
@MikesMiniMotors3 ай бұрын
Haha, thanks! I just looked at my Dragy log, and the 0-30mph was exactly 7.00s… Great guess! 😂