BLDC Controller Learning Board for Beginners (HI-BRAKE/CRUISE -CONTROL/REVERSE/SELF-STUDY) (PART 2)

[@0dbm]

Your videos are excellent

The most complete videos about modules for electric vehicles that I've seen. Thank you very much.

[@ronmoz5815]

I was happy your actual demonstration, very simple, easy to understand, and I enjoyed

[@EVCustoms]

Thank you man...

[@RIKOARIshowreel]

Thanks! Now I know what "Self Learning" cable means.

[@alexjee5049]

This is really well laid out and informative. Sincerely, I thank you

[@carlitomadrona6211]

So far this is the most easy to follow👍👍

[@radodanchev8600]

How to get 100% power in revers and forward. Nicer burnouts in revers😆 Very nice video, I love it

[@aniruddhashinde]

Loved the effort you put in , it's super easy to understand

[@EVCustoms]

Thank you mate!

[@michaelfernandez5935]

I'm here part two thank you sir,🙏🙏🙏

[@africans1968]

Thank you for your videos, I'm learning a lot

[@fletcher3913]

Your video was very helpful. Thank you.

[@rsajjid]

Fantastic clearly explained, I do not use throttle do you video on how to connect Pedal assist sensor PAS connection

[@JJLB-JoJo]

Just perfect vidéo!! thx

[@EVCustoms]

Thank you mate!!

[@01Joemama]

your a legend. so simple and clear thank you

[@idrisabubakarmuhammad9226]

Very very useful video thank you

[@dchandar1876]

Thank you for your videos please upload thired part display conection

[@jefrindelacruz]

Very informative

[@barneygoogles5186]

Thanks Great video!

[@marine1718]

Thank you!

[@JMSERVIS]

Perfektní videa, jen kdyby byla ještě k tomu poradna, kde by člověk dostal odpověď, tak bych byl úplně spokojený! I bych zaplatil, nebo přispěl na provoz. Já mám ten problém, že neumím jazyky, tak musím používat překladač Google, ale to není stoprocentní, možná ani poloviční! Proto musím sledovat video několikrát, protože když sleduji ruce, nemohu při tom číst titulky! Tak to musím zopakovat, abych zase sledoval to opačné. Měl bych hodně dotazů, jen nevím kde by mi je zodpověděli...!? To je strašná škoda, když tomu někdo takto rozumí!

[@JawadAhmadsahibzada]

I’m continuously learning from your videos as I’m building my Ebike. Thank you. I have questions. 1) I have seen people connect high brake wire to tail brake light positive wire (12v) to activate. Is it safe ? 2) for low brake , I’m using handle bar switch , which is usually used for brake light. How can I wire low brake and brake light to same one switch or it’s not possible !!!

[@EVCustoms]

Hi 1) Yes i have do that also, 12V signal to hi brake input, it's ok. 2) yes you can do that also, i will make you diagram when i will have free time ok? send me your email

[@kaylor87]

I'm having trouble with my brake wires... They do seem to cut power, but I don't notice any actual braking force. It just seems to stop throttle... Is that normal, or am I doing something wrong? I'm using the low level brake wires, just connecting the two together with a switch. I was hoping for an actual brake.

[@eneagiuffrida7996]

Same problem how did you solve? I tried to connect high brake but nothing happens

[@kaylor87]

@@eneagiuffrida7996 Yeah, makes no sense. I don't think they actually brake at all, just cut power to the throttle and cruise control. Which is lame. I even opened the case and soldered wires to the regen braking pins, and nothing happened :(

[@eneagiuffrida7996]

@@kaylor87 so i had 3 controller before this and no one gave me problem with high and low brake. I have puchased a 24 crappy china mosfet and im having problem only on this controller

[@eneagiuffrida7996]

@@kaylor87 im trying to open the controller and search in live for ebrake function. The only one doubt is that i put +48v signal on high brake but maybe only 5 volt where needed

[@kaylor87]

@@eneagiuffrida7996 ohh wow, really? So on previous speed controllers you've had actual electronic braking that works?

[@dainiusjaraminas6412]

perfect:) thank you

[@TheGadagada]

Exelent explanation

[@EVCustoms]

Thank you!!

[@MsDjDenis]

Grazie per il tuo video..

[@heleneparadis5744]

We have a foldable Gotrax ebike that suddenly stopped running. We changed the throttle and the bike works only intermittently. After further observations we realized that the wire connected from the throttle to the box is defective,probably due to the folding and unfolding of the bike. Can we change that specific wire only and how do we do it??

[@ajinkyadeshpande6271]

Very informative. Can you Please tell that how you have assembled the motor on the table. What keeps the motor perfectly horizontal.

[@hasger1941]

how will the regenerative function work please ?

[@winmarkesconde5651]

So the high brake can be activated by system voltage, i thought i will need separate 12v supply to do that, thanks for the video.

[@namdevkhamkar387]

Sir thank you very much

[@ossamabenhamou3070]

I have one question to ask you about. firstly i like your channel so much and it's so helpful and so meaning thank you for all this. my question is the next. - i have a 48V 1500W hub motor and a 48V 20A battery, what kinda fuse should i use to protect the motor from overload shocks and CC faults ? thank you again and keep it up !

[@EVCustoms]

Hello my friend.. Most important to know is you controller line current, So if your motor specs is 48V 1500watt (31Amps) there ideal controller must be at 48V 60Amps (3000watt at start) so you will need double 30A fuses in parallel

[@ossamabenhamou3070]

@@EVCustoms the supplier i bought from gave me a controller of 48V 35A, although i should use 2 fuses in parallel of 30A ?

[@EVCustoms]

@@ossamabenhamou3070 for 35A you can use 2x 20Amps fuses in parallel with 4mm line wire from the battery...

[@ossamabenhamou3070]

@@EVCustoms Thank you so much, you’re a great man 🙏🏻 and good luck with more successful customs

[@EVCustoms]

@@ossamabenhamou3070 Thank you mate!

[@jasonbrown467]

thank you for the video. i accidentally bought one of these controllers for my ebike bicycle and the instructions were very poor. now maybe i can get the electric motor brake to work. i still dont know why one is called high and the other low.

[@jasonbrown467]

here i am again, 7 months later and i did get the regen brake to work, but i dont remember how, so i am researching this again.

[@chamindamonarawila6243]

thankss

[@r0ck3tdr1v3r]

Where can i find a 3 pin julet to 3 pin jst connector, for connecting the low brake. + How to activate e-abs?

[@amjadaliraza487]

Zabardast 👏👏👏❤️❤️❤️

[@manob198]

Sir please upload a video about power cut off brake troubleshooting and repair. ...

[@michaeltheertham2131]

Sir,can you Please upload a video regarding how to check the bldc motor controller whether it is faulty or working by using digital multimeter. Thank you.

[@TheMrjogas]

Hi 👋 great video reverse wires what voltage have

[@gearcnc]

Good vídeo sir, I habe 2 new motors, are of 48V 1000W, My problem is that the selft study not work, not move nothing I don't know what happend.

[@guydecamp9494]

I have a 1000W controller connected to 350W motor it is running slow need to know will it work??

[@TheAlbigensis]

How about parking...is the bldc will stop moving on parking mode or just disconect the power?

[@paulocardoso467]

Hello, how i switch 4 motors to one throtle? thanks

[@wahida5355]

Can you help me about the 12v converter to connect on back light and cut off brake.

[@이도권-l1c]

Are high/low brakes regenerative brakes?? Do they actually charge batteries??

[@EVCustoms]

Yes my friend of curse..

[@이도권-l1c]

@@EVCustoms thank you flr answer. I wonder how low/high brakes differ from EBS brake you explaned. All of them are regenerative but EBS is much stronger??

[@nerdy1018]

How would you derestrict the speed limit?

[@estebancasillas5775]

That's what I'm trying to figure out too

[@E-BikingAdventures]

I think the high break stops the motor faster. It maybe easier to tell if there was a load on the motor.

[@EVCustoms]

Hi... no it is same think, difference is that on high brake you can connect stop light, so when you breaking stop light will turn on..

[@srnunan4783]

How slow will this controller drive the motor? Can you have it supplying a small current that is small enough to not turn motor?

[@kamote4854]

Could you also make a video on the head light, turn light, break light, and horn. On a 48v battery with 12V light, 12V switch, and 12V horns

[@logikai]

Lights(horn, signal, tail and front) are usally not controlled by the controller. See it as another circuit. Use a converter from your battery voltage to 12 volts(a.i. 48v-12v). The circuit runs like this: battery->(key)switch->converter->handlebar controls(a.i.switches)->lights,signals,horn,brakelight

[@nileshgupta6265]

how can I found ignition cable ? plz help mi i have wire less controller

[@vvdd903]

how do potentiometers get added to the system?

[@carloscruz8564]

Question. How do I increase the speed of this type of hub motor, there are different ways to do that?

[@dimatraval2651]

Hello how make 48vscooter vsett8 run faster? Change controller? Help me please.

[@darylsnelling6394]

Hi how do you wire re gen braking on a hub drive ?

[@cantal88]

What kind controller You use and You can recomend for this motor? Thanks

[@f0xvibes]

Is cruise control basically a ground loop, that we need to close? I'm asking because on my controller there is only one pink wire for cruise control, no corresponding wire...

[@kaylor87]

Interesting, did you figure it out? My cruise has two wires, and when they touch together cruise activates, when they touch again it deactivates. So I use a momentary switch, push once for on, push again for off.

[@rusc2173]

hello great video. i have a question about a problem i currently have. i have a 72v 3000w motor and a 48-72v ecu. the problem is that no matter which battery I connect 48v or 72v I suddenly have no more power and have to disconnect the battery. do you know what that could be?

[@fariskhalida]

Hye. Sorry. The connector wire for reverse funtion, can it be used RC light switch 5/6v so turn it on? Thank you

[@hugosanchez1615]

Hello...you really teach.... Thank you...also can You help.me I try to connect a 12v front light but I didn't find any 12v output fron controller how can I do it ? Thank you.

[@logikai]

Lights(horn, signal, tail and front) are usally not controlled by the controller. See it as another circuit. Use a converter from your battery voltage to 12 volts(a.i. 48v-12v). The circuit runs like this: battery->(key)switch->converter->handlebar controls(a.i.switches)->lights,signals,horn,brakelight

[@schimu90]

Is there a way to adjust the punch of the motor, so it accelerate immediately instead of slowly increase the speed?

[@EVCustoms]

This depends from your controller, it has display on it?

[@schimu90]

@@EVCustoms No, it's actually a cheaper one. But I thought it could be possible to remove some components in the circuit board to do so...

[@emigrant4life]

my controller sometimes reset "self study" after some time or after charging... I do not know why... (48v/500w)

[@cohengal1584]

hii , the difrent betwhin low/hi break is low - stop the motor(therthl) hi- is regan break ( conect ampmater to the batery) isn't??

[@theProjectHunter]

hi, did you test it? :) כהן ד

[@leluthebluebayshepherd3551]

Hey buddy I've been a sub & fan of ur channel for a while now & was jusg wondering if u kno of a good Sensorless BLDC Hub motor controller for a 2WD Electric scooter build I'm doing? I have two 3phase bldc hub motors already & am looking to get 2 controllers that can handle voltage from 48V-60V. One for each motor (Front & Back)...please let me kno cuz my motors have no Hall Sensor wires just 3phase. Thanks u!

[@ahmadzaki3328]

For my info the low and high brake are not the same!

[@cjt554]

Where can I purchase the controller you're using for the demonstration?

[@cjt554]

I've been looking for a controller with cruise control

[@josephaltman460]

I found info that says high brake is ebrake.

[@kushalshiwakoti529]

how can i check the voltage of hub motor, which wires do i touch with my probes, I am little confused as there are 3 phase current.

[@VichetSSom-ck8jd]

I love your video's and I learned a lot from watching them. I got a question for the experts that can point me in the right direction. I have an Aerlang h6 v2 500w 48v 17.5a electric scooter and I want to make it faster. What do I need to change and do to make that happen? Do I need to change the speed controller? Battery? and or the motor? Thank you in advance!!!

[@elias8981]

Battery and controller. You can keep the same motor but it will heat faster

[@VichetSSom-ck8jd]

@@elias8981 Thanks for the reply, one more question.... can I upgrade my controller to a 1000w 48v even though the motor is rated a 500w instead of using the 500w 48v controller?

[@elias8981]

@@VichetSSom-ck8jd well you can do this but if your are planning on using the max power 1000w for a long period of time during long trip, be sure to check if your motor isn't too warm. On high end controller, you can normally see this on the screen but i don't have one myself so just check the temperature

[@VichetSSom-ck8jd]

@@elias8981 I like to thank you for the information you have given me. You're awesome, BIG THANKS!!!

[@elias8981]

@@VichetSSom-ck8jd no problem dude. It would have been nice if someone told me all of this a while ago when i was learning about ebike so i try to help if i can

[@rahmansajjid9143]

Hi, Do you Have PAS based video, I am not using throttle looking for PAS set up driving the motor

[@TRIIIPLX]

I have a problem I don't know which battery I should use to power the 2000w brushless motor can anyone send me a link to a suitable battery please

[@bigbigboy2011]

Hi, how do i connect the gps tracker black and red wires to the controller for power ?

[@edenglish8318]

How do you wire a volt/amp/SOC meter in this circuit?

[@vadymhaidachov]

Tell me please. Is battery charging while low e-brake is active?

[@EVCustoms]

This is depends if you have activate the EBS brakes and your vehicle breaking when you pull brakes, if not your vehicle just deactivate the motor when you breaking.

[@kushalshiwakoti529]

my bike ebike throttle speed is limited to 6km/hr , i cant get it upto 25 , because it ask me passcode which i dont know and the company also couldnt help me, should i change my lcd or change the whole controller? please give me some idea.

[@solarsynapse]

What motor are you using? Where did you buy/how did you make the hub motor reverse? I thought all hub motors had one-way bearings for freewheeling. With a one-way bearing, the brake does not actually brake or regen, it just stops the motor. Without a one-way bearing, you can't freewheel and would have the drag of the motor.

[@logikai]

There are 2 kind of hub motors: geared are freewheeling so you can’t ebrake with these. The other(don’t know it’s name) with freewheelfunction and can e-brake

[@The_Courage.]

Can we connect Lead acid batteries to bldc hub ?

[@EVCustoms]

You mean on blcd controller.. yes

[@SlobodanMiletic]

i don't have reverse exit on my controller. Can I add it in someway??

[@EVCustoms]

Hi.. there didn't exits controller without reverse, for sure you have.

[@yobruh6029]

How do you add turn signal lights?

[@freddilkes5936]

Is the cruise control really an "amps control" or does it actually control the speed of rotation no matter what the amps required to maintain that speed? On my Golden Motor kit, I believe it is the former.

[@logikai]

Depends on the controller and maybe it’s settings...

[@FrancisWiegers]

does the throttle need to be connected for the self learning cables to spin the motor? I am trying to test a new controller and going in steps. I have tested the motor with a tester so I know it works. The tester shows 5 volts leaving controller so I know it's getting power from battery. If I connect the learning cables shouldn't the motor spin with or without the throttle connected?

[@EVCustoms]

On some controllers throttle must be connected,,, on other Controllers the motor spin automatically..

[@sumopanda5070]

is that a duel blc? ,Id like to add lights Erm signal lights,do you think you can do a video on that to?

[@logikai]

Lights(horn, signal, tail and front) are usally not controlled by the controller. See it as another circuit. Use a converter from your battery voltage to 12 volts(a.i. 48v-12v). The circuit runs like this: battery->(key)switch->converter->handlebar controls(a.i.switches)->lights,signals,horn,brakelight

[@jasonbrown467]

is there a way to increase amps without modding the shunt? my controller is only putting out 47amps, but the label and and the seller says its 80amps

[@jasonbrown467]

this was most likely due to several bad hall sensors in the hub motor, i swapped to the original controller and it wouldnt work at all and found the bad hall sensors and replaced them. 7 months later and i am now putting the 80 amp controller back on and i have 80 amps for sure.

[@customrd]

I Love the Shunt mod

[@noahhorner5417]

Hello, I have a problem with the brakes If I put the High Brake Line on +, the engine just shuts off, but it doesn't brake. Can somebody help me? LG NH

[@noahhorner5417]

Ps: the video is very nice thank you👍🏼💪🏽

[@EVCustoms]

Hi... you must activate EBS function for that,,, find EBS pin on your controller PCB and connect it with GND

[@dubi338]

wich controller ist it ?

[@lumilumi5752]

👍👍👍

[@sumopanda5070]

im trying to get light to work do you know anything about that & thankyou in advance

[@logikai]

Lights(horn, signal, tail and front) are usally not controlled by the controller. See it as another circuit. Use a converter from your battery voltage to 12 volts(a.i. 48v-12v). The circuit runs like this: battery->(key)switch->converter->handlebar controls(a.i.switches)->lights,signals,horn,brakelight

[@sumopanda5070]

@@logikai i think ive done it....yes its good ,i need a flasher 2 pin ....thank you

[@MohamedharishA]

how to code it

[@muhammadaleemadil]

plz add subtitles to your vedioes,, ASLO THE INTRODUCTORY VEDIO IN THE SART OF EVERY VEDIO ON THIS CHANNEL IS VERY ANNOYING PLZ CHANGE IT. OTHER YOUR CONTENT AND KNOWLDGE IS VRY HELP FULL .THANK YOU

[@AbdifetahKedir]

UsB

[@barelarnon5578]

PART 3 WARE ???

[@mohanmohan-kl7st]

Hi brek canaction 12 v ya 48 v

[@vidurasilva3624]

can I help me

[@002-b9s]

Where is the arduino display project 😭

[@EVCustoms]

:-) man... until now i am on arduino tow way power meter... unfortunately i have big problem with my time...

[@002-b9s]

@@EVCustoms of course i am joking on this one.... take your time please don't hurry. Enjoy it 😄

[@mohanmohan-kl7st]

👍👍👍👍👍👍👑👑👑👑👑👑👑

[@DwarfSin]

Friend I am using qs motor and votol controller. How do I use regenerative braking? Just connect the high break line to +? Without battery 12v 72v dc converter??

[@EVCustoms]

Hi friend... send me model of your Votol controller.

[@Excaliburt]

Very nice, thank you.