BMW E46 Crankshaft Pulley amzn.to/3dt4HMr (UK) amzn.to/37TCz3Y (INTERNATIONAL)
Пікірлер: 42
@Henry_R5 жыл бұрын
Thanks for good video Sandy! I manged to get it open by using fifth gear and brakes, just in case added spanner to driveshaft flex disc bolt to hold against body. But damn it was tight, I had to use 3/4 sockets and 1m pipe :S I could not find opening to flywheel underneath facelift E46 320d manual, otherwise I would have tried your trick also.
@sandyande5 жыл бұрын
Glad to help cheers sandy
@mattgilbert75475 жыл бұрын
Great guide thank you
@nopy996 жыл бұрын
happened to me too. crank pully disintegrated at 110k miles. ststement of the obvious but its recomended to change the belts at the same time.
@MohVlogz6 жыл бұрын
kzbin.info/www/bejne/mH-yZJWJl9eNfKc
@Adam-bw4lw7 жыл бұрын
damn 420 that crank pulley is high af
@MohVlogz6 жыл бұрын
Adam 1 kzbin.info/www/bejne/mH-yZJWJl9eNfKc
@alanmannion86705 жыл бұрын
220K Miles and no pully, but this is why im looking at this video. Thinking of doing.
@Delboy-jb2ss4 жыл бұрын
Use a small jack to hold the chisel in place on flywheel if u dont have another of hands ready
@dimagerman88346 жыл бұрын
Hello friend.There is a problem and I'm looking for advice.I have a bmw E46 diesel 2003.The problem is that I'm in the last year changed 4 times the crankshaft pulley, it something BREAKS , but I can't understand.Thank you
@sandyande6 жыл бұрын
Dima German hello friend ask these guys kzbin.info/door/Hr8jUDLpkcYgg3Axhu7qhw they are BMW experts, could be partially seized Aircon compressor or another pulley?
@MohVlogz6 жыл бұрын
Is your car Remapped? What bhp is it?
@haiqalhanapi19486 жыл бұрын
serious question. what accent are you talking in?
@klaudiaracz4385 жыл бұрын
Scottish
@TehNouk6 жыл бұрын
why cant i just put it in gear soo i get the crankshaft pulley bolt loose?
@MohVlogz6 жыл бұрын
Check out my vid it explain better kzbin.info/www/bejne/mH-yZJWJl9eNfKc
@Classic_Re-creation5 жыл бұрын
Is this just a normal threaded bolt left to loosen and right to tighten?
@sandyande5 жыл бұрын
Yes it is my friend
@Classic_Re-creation5 жыл бұрын
@@sandyande thank you going to tackle mine tomorrow
@alz7225 жыл бұрын
Can't you leave the car in gear with some one sitting in it with their foot on the break to lock the engine up?
@sandyande5 жыл бұрын
Tried that no chance!
@raino185 жыл бұрын
Did this pulley also cause vibration at idle speed?
@sandyande5 жыл бұрын
Yes
@NG-zg8vf4 жыл бұрын
Why would u do it in 6th gear? Stick it in first, handbrake on and get that bolt off
@sandyande4 жыл бұрын
Tried that doesn't work
@gocekipro13054 жыл бұрын
At which mileage you replace the crankshaft pulley
@sandyande4 жыл бұрын
130,000 miles
@Eddiebayes1774 жыл бұрын
Dose anyone know how todo with automatic gearbox??
@erixlast60204 жыл бұрын
Nop
@tewendeblaise78763 жыл бұрын
Kia sportaj 2008
@crni7225 жыл бұрын
Do not lock flywheel, it put too much stress on crankshaft, use proper tool.
@sandyande5 жыл бұрын
Haven't got proper tool, one must work with what one has available!!! I've had no problems since repair.
@alz7225 жыл бұрын
What propper tool?
@twowheelsonelove40404 жыл бұрын
I replaced it exacly as it said here but now car wont start...
@sandyande4 жыл бұрын
Petrol or diesel?
@twowheelsonelove40404 жыл бұрын
Diesel 320d
@sandyande4 жыл бұрын
Are u getting RPM reading on tachometer/rev counter when u crank it over?
@twowheelsonelove40404 жыл бұрын
Yes the rod lifts a little bit above the 0 in spidometer when i try to crank it
@NG-zg8vf4 жыл бұрын
How would crank pulley affect the car starting?
@marijabosnjak14213 жыл бұрын
you talk very quickly about slow actions in the work phases and your English is unclear and bad ...
@sandyande3 жыл бұрын
Hello, English is not my first language it's broad Scots!!! Cheers sandy