I am amazed that didn't destroy the cylinder. Great video btw.
@envisionsexful4 жыл бұрын
Love it or hate it. BMW engineering is magnificent! As complex as this engine appears to be it is nothing short of a MARVEL!
@rollydoucet89093 жыл бұрын
The engineering is magnificent, but the bean-counters settle for cheaper, poor quality rubber seals and gaskets, resulting in leaks and engine failures.
@sanobike3 жыл бұрын
Great videos and very helpful, thank you! I have a S63 in the middle of valve stem seal replacement. Engine in car, valve covers off, started to set time for cam removal with AGA tools. Rotating clockwise a bit reached a hard stop, short of reaching MP. Engine would rotate back a little, then stop when going forward at same place. Saw in TIS that it is OK to back rotate as long as chains were tensioned. Still had tensioners in place, so spun the engine nearly a full revolution backwards and achieved MP mark for crankshaft and all four cams are dead on with timing check plate. Interestingly, with timing tools removed, the engine will only turn a little forward and little backwards. Feels like a hard stop in both direction now. Ever seen something like this?
@MrSamPhoenix8 ай бұрын
Great video of this beast of an engine. But the camera shake got me dizzy 🥴.
@fatcatsgang6 жыл бұрын
S63TU, Tasos! Love your videos! How many KMs on this engine? Very interesting to see the main and rod bearings so worn out. At the dealer it wasn't un common to see rod bearing issues. Also, I too love how BMW used actual gaskets. Unfortunately, with the B series engines a lot of sealant is used now, oh well.
@TG-ok4ty5 жыл бұрын
What brand/weight of oil do you like for that engine?
@ratiualin4291 Жыл бұрын
Amazing. With what degreaser did you wash the engine block? I can't wash it like that with the degreaser I use. Thanks a lot!
@KalchykDen2 жыл бұрын
What oil did owner of engine used? Also what oil viscosity and brand would you recommend?
@azoozazooz32696 жыл бұрын
Is there any deference from N63 engine, because what I am see it has same N63 engine block, can you explain if it has any deference, thank you.
@VIKASKUMAR-nd3qb3 жыл бұрын
Very helpful video.
@AH835945 жыл бұрын
IS the engin to transmission bolt patern same on s63 and n63?
@m5james6 жыл бұрын
I noticed this is a S63TU (F1* M*) based on the crossbank headers vs the S63 (E7* X*M) that doesn't have crossbank. Do cars usually have no cats on the downpipes there?
@ante43315 жыл бұрын
Am i seeing good or the intake and exhaust valve diameters are the same? Shouldn't intake valves be bigger in diameter??
@8920169012 жыл бұрын
Hi. When cranckshaft and bearings is damaged you change oil thermostat or not?
@paulkalin2 жыл бұрын
Hey could you point me where to get all the torque specs for head/mains/rods/ and all the other relevant bolts. My s63 spun a bearing and I’m replacing the crank
@isaacrodriguez97875 жыл бұрын
That coyote though!😍
@TasosMoschatos5 жыл бұрын
Isaac Rodriguez hi, actually there are 8. kzbin.info/www/bejne/e2HHZmqLjslgq8k
@erkancelik72026 жыл бұрын
very nice video
@yunielizondo4927 Жыл бұрын
Hello, good afternoon, what is the possibility if the engine is tied up because a problem with the connecting rods has caused the engine head valves to twist?
@starshiptrooper45063 жыл бұрын
Is the audi 4.0 v8 better or worse than n/s63?
@TheArabsolga6 жыл бұрын
Really cool videos. Subscribed.
@ante43315 жыл бұрын
And wow i never saw a piston broken like that! So did the owner heard some strange sound or this was like preventive inspection? I mean that piston almost destroyed the engine
@meayman16 жыл бұрын
Dear Tasos,hope to find you will . I need s63tu flywheel do u know where i can get it in uae?
@TA-mm7rv6 жыл бұрын
Good video 👌👌👌
@TornadoF605 жыл бұрын
Was this a stock or tuned Engine?
@Merrill30005 жыл бұрын
How many Km did this engine have?
@mrg26736 жыл бұрын
What engine block is this ?
@jameslatimer14323 жыл бұрын
Is number 8 piston rings cracked ???
@g.king.5 жыл бұрын
Amazing video man, thanks a lot !!! keep them up
@marknarain77265 жыл бұрын
Use a feeler guage to remove the rings so that you don't hurt yourself
@universeu72894 жыл бұрын
The "hair dryer" you use it is called heat gun :)
@challenger39675 жыл бұрын
What's up with that coyote in the back?
@EUROWORKS6 жыл бұрын
It's heat gun!
@maxcotronlinux9 ай бұрын
Do you happen to know the dimensions of the engine?
@million1274 жыл бұрын
one man one engine
@Allbigbones6 жыл бұрын
They call it heat gun ( hairdryer )
@mbgtcentre92915 жыл бұрын
the crankshaft bearing arent good calculated just that
@maximilianlindner3 жыл бұрын
2JZ as a ring tone... lol XD
@thekillerking73933 жыл бұрын
Km ?
@MrUkielover4 жыл бұрын
Tasos, how much does a job of this magnitude cost? Interested in having my s63 engine rebuilt
@eminsergi90154 жыл бұрын
What is ur car? X6 m?
@MrUkielover4 жыл бұрын
Emin Sergi, It is a 2012 X5 M (E70). s63 engine.
@diablocls552 жыл бұрын
@@MrUkielover lol One of my homies has a 2012 X5M with about 115k miles that he drives hard all the time. I’m surprised it hasn’t needed a rebuild yet
@frederiquekruger48182 жыл бұрын
The N63 rebuild in his other video cost around 13,000 EUR. This would more or less be the same.
@MrUkielover2 жыл бұрын
@@frederiquekruger4818 Just had my s63 rebuilt. $11,000 for the rebuild & another $4000 for removal/ installation.
@1DessyDsm12 жыл бұрын
Hello, How common is it for an s63 to have a blown Headgasket? I just purchased one and the dealer diagnosed it as "defective Headgasket" I have been searching everywhere and no one has ever heard of a headgasket issue with an s63 I hope it is misdiagnosed
@THBMW Жыл бұрын
Been working on these for 10 years never seen one with a bad head gasket
@mykolapelyp90653 жыл бұрын
"here is the piston, open the door, close the door" - L O L)0)
@chrisc16235 жыл бұрын
Just curious from your experience if these engines are great and reliable??
@Cuzn555 жыл бұрын
Chris c fuck no.
@jokerash4 жыл бұрын
they are if you change the oil every 8000km and do not floor it when it's cold.
@rollydoucet89093 жыл бұрын
@@jokerash Over-revving cold engines is the worst thing people do. Next comes lack of maintenance.
@SlickJeff20206 жыл бұрын
If you get a chance can you do us a favor and run a comparison video on M157 connecting rod with N63tu rods just to establish which rod can withstand more abuse.
@thekillerking73933 жыл бұрын
Por la voz pareces español ? Estoy en lo cierto ?
@EuropeanDreamz5 ай бұрын
Do you remember if an injector failed melting the piston ??
@EuropeanDreamz5 ай бұрын
Btw this is Devin 🙂👌
@chrisej59876 жыл бұрын
Is this the 4.0L? This JUST came out in the S class and ppl are already blowing them up! 😂
@TasosMoschatos6 жыл бұрын
Christophe Johnson hi, it's BMW S63 engine, usually I'm writing the engine code on the video title. Thanks
@chrisej59876 жыл бұрын
Tasos Moschatos haha sorry. That’s true you usually do. Duh. 🤪
@darylmorse2 жыл бұрын
Lucky owner that the engine isn't scrap. Really interesting to see this engine opened up, but please get a better camera and get some video skills. The camera is out of focus and moving around too quickly.
@Shaun-77995 жыл бұрын
This is the s63 bmw engine or he is rebuilding an merc s63 engine ?
@sonerd.14595 жыл бұрын
Shaun 7799 its from bmw :)
@turbosupercharger Жыл бұрын
8:11 звук двигателя, такой говорит S63, смотри я наваливаю
@kimkwanghyun84333 жыл бұрын
f10 M5?
@TasosMoschatos3 жыл бұрын
Yes
@Yankee70002 жыл бұрын
Perhaps a cultural thing or maybe it’s safer: keeping a record of what you find so that the customer believes you…..
@ishaqalbusaidi86446 жыл бұрын
What type of oil is good for S63B44TÜ engine?
@awfulhak50345 жыл бұрын
Liqui Moly 10W60 changed every 8000 km
@awfulhak50345 жыл бұрын
CheckYourGear There are many M5 F10 which are running on this oil. I know few owners who are running M5 on 10w60 from many thousands of kilometers. If anybody if worry about usage of 10w60 then can use Liqui Moly Molygen 5w40.
@mbgtcentre92915 жыл бұрын
maragrine
@mbgtcentre92915 жыл бұрын
the best one is Polymere oil 5w40 or 0w40 depend of where you rpm.
@tonyigori79804 жыл бұрын
@@mbgtcentre9291 pls a place like Nigeria wish oil can I use for BMW n63 2008 thanks
@MrZattack1013 жыл бұрын
10:50
@TheRealAnthony_real6 жыл бұрын
I see you did not inspect at all the ccv under the cam covers ... I believe this is the issue why these engines consume oil more than required ... In no boost operation the vapours are going directly into the engine inlet ports through some channels in the heads ...
@TasosMoschatos6 жыл бұрын
vlad bozantan because you didn't see it on the video this doesn't mean that I didn't check it, I took it apart and I clean it like always.
@TheRealAnthony_real5 жыл бұрын
Tasos Moschatos I have a 2014 s63tu engine and it started drinking oil heavily ! 1L at 250 miles and I wasn't comfortable with the amount of oil that it drinks all of the sudden ! I have started investigating with a friend of mine and it turns out that when we removed spark plugs on cylinder 7 it was lots of soot and oil residue on the spark plug , damp ! We then managed to insert a scope camera inside the cylinder 7 and found out that the cylinder wall is all porous at the base of the cylinder, lots of tiny little holes at the base (when the piston is in the bottom dead center) 10 mm high 40 mm long portion of holes !!! Why would that happen ?! I heard the sulfur in the fuel may damage the cylinder walls ?
@TheRealAnthony_real5 жыл бұрын
The car has 73k miles the cams are perfect , no wear at all however he cylinder walls are damaged (no vertical scratches from the rings but small little holes here and there ) cylinder 6 as well not as bad as 7, also some holes on cylinder 5 just started forming holes here and there . I'm stunned how can a V8 block from M5 develop such of damage ? Full BMW history , I had it for 1 year with no problems (2nd owner) the car only started to loose oil more than normal 3-4 months ago !!! I was topping up 1L 250 miles ... Jeez
@QwertQwert-mv9mw4 жыл бұрын
Я 8 цилиндр поршень снизу снимал ))
@MisterMili2 жыл бұрын
Im here to save this just incase I blow my engine ..