Forscan - How To Navigate - What Each Button Does

[@RonnieWeinman]

Even though your videos are 2 years old, they are new to me and I found them to be just the helping hand I needed to use this software. Cheers

[@artfisher1235]

Great video instruction. Also, as an American, it's good to see your empathy for the French. Love is what makes the world go 'round.

[@Cowboycattlehauler911]

Man thank you so much for doing this and your other ones freaking helped me out so much u have no idea . Best damn video on KZbin something actually worth watching

[@SYDiagnostics]

thanks for the comments

[@paulchester656]

Hi again Steve, brilliant video on explaining the basics of Forscan. Just what someone like me needs. Really look forward to following your videos.

[@colincollevy7658]

Hi Steve, you can see on the bottom left of the screen when the scan is complete, it’s turns from ‘reading vehicle info’ to ‘ready’ Been using this software for years and never realised it had any bidirectional controls until I watched one of your videos, keep up the good work, thanks

[@SYDiagnostics]

Thanks for the tip, every day is a learning day

[@gerrymcivor374]

Brilliant, just what I needed, a clear and understandable explanation. Thank you.

[@twiggacott]

A good first start, now to watch the detailed ones about how to change settings.

[@earlbrianplaza6647]

Wow. Forscan don’t have this instructional video and I appreciate this video you made. It’s very useful for beginners like me. Will be exploring your channel to look for HID conversion configuration

[@tedschuurmans]

Awesome, subscribed and liked. This was the video I looked for ! Thanks !

[@dadybow]

Brilliant Thank you very much installed forscan today need to learn a few things like bleeding the ABS transit and removing TACHO

[@stevehayes6661]

Nice clear description

[@rubendawn7478]

Very well done and for sure appreciated by many. Thank you for sharing your knowledge!!!

[@SYDiagnostics]

If you can think of any other ideas let me know 😉

[@rubendawn7478]

@@SYDiagnostics Probably it will be worth mentioning not all years have the same modules and same capabilities. I couldn't find a way how to enable the cruise control on my 07 Ford Explorer there is very limited capability to change anything unless is in the "As Built" form but there is no spreadsheet for my vehicle. Any pointers?

[@JaySmith-mw4dv]

thanks for taking the time out as it been a big help...cheers pal

[@sparkyindahouse]

Thanks for adding your videos, i am finding these very usefull as i am fresh to using forscan. Cheers.

[@SYDiagnostics]

Thanks for the comments and support

[@andrewbeddoes205]

Good video Steve ,well explained and informative,keep the videos coming,well impressed with all SY DIAGNOSTICS videos.

[@francisphillips8192]

Brilliant info i did'nt see the auto connect just ticked the box now

[@DR-xv8ps]

Really well done, Thanks

[@philc70]

thanks for the info and effort its appreciated

[@soulfuldos]

thank you

[@AbbottAutomotive]

As always good work 👍🏻

[@63Arnast]

There are some sections of the Forscan software that require you to register like installing a new stereo that requires coding to the vehicle. It is totally worth it, just wish there was something that can tell me what all the modules do that come up. :)

[@kieranthomas5478]

Amazing video. 👏 got few questions soon if thats ok. Trying fix my van

[@andrewgray3482]

Cheers mate

[@PAULSMITH1967]

brilliant anyone know how toturn the headlights off on startup

[@phmechanicplug4493]

Hello Steve, great video you have here, and if you don't mind, would you like to ask if you have made a video on how to program or perform an ECU swap using Forscan on Mazda cx-9? thanks.

[@SYDiagnostics]

Thanks for the comments. At the time of making the videos I was working at a Ford dealer, I no longer work there and have a role now where cameras are forbidden

[@aquaman0167]

At 1:04. At the lower left you will see the “ready” appear when it’s done reading a page.

[@SYDiagnostics]

Yes, that's correct. Since making the video I've found this. But sadly cannot update the video. Thanks for the comment and for viewing

[@chrissing64]

Thank you great video. Do you have a vid on activating an aftermarket reversing camera pleas?

[@s1tuningsheffield62]

Hi m8 thanks for vids I have a 2016 transit courier 1.5 it is limited to 60 can I disable it in forscan if so can you upload a vid or any info would be fantastic Thanks

[@stevebiggs6314]

Great video. At 2:00 you mention that it shows the latest available versions for the modules. Is there any way these can be found / downloaded and installed?

[@SYDiagnostics]

they can be downloaded from the Ford motorcraft site as far as im aware, but Forscan is unable to perform the software updates

[@jorlopez26]

Do you have to do the wire or pin swap on both sides, driver side, and passenger side? Also getting an error. I’ve tried to since I have a 4key fob, do I need to use the FC code, try without didn’t work then I did it with FC didn’t work. Too much on the driver side and I’m getting a short ground error on the DTC on the driver module clip the wire a 3m connector. No errors on the passenger side module just on the DDM. What do you suggest?

[@androidemulator6952]

Hi, very informative video-thanks. I have a Ford Escape 3.0 v6 engine - any away to use Forscan to isolate (turn off) individual fuel injectors ?

[@SYDiagnostics]

I've only ever seen that on ford test plan programs. The functionality ford allow is incredibly limited

[@kitmoore9969]

@1:00 How do we fix the warning triangle on the first logged entry "Checking J2534 Ford-VCM-II ..."?

[@rabbitpork8935]

Thanks for the useful info and tutorial. Could I ask you if Forscan can read all fault codes? I mean can I be sure that if I Forscan shows no DTC, the car has actually no faults? Thanks in advance.

[@marcusbarnes5929]

Do you have a video on how to save the factory data profile for back up before changing settings and numbers just in case somthing goes wrong and can be set back to factory standard.

[@SYDiagnostics]

I have a video on how to activate auto locking on a kuga. In that video I show how to save the original configuration for back up

[@danman9017]

nice video,can forscan do test like cylinder balance test,and other test

[@SYDiagnostics]

Just like IDS , forscan will differ on its usage, vehicle to vehicle. One of the things i dislike about Ford is that the functionality is not the same throughout

[@durvalbbk6786]

👍

[@optics4062]

Great video. My 2013 Ford Fusion has the abs light on, traction control, and brake light on. They popped up when the wiring harness for the engine coolant sensor broke and was fixed. I did a full brake job, checked that the wheel sensors all read the same with Forscan. Have zero dtcs on Forscan and cannot figure this problem out. If I engage the electronic parking brake the lights turn off tell the epb is disengaged. Would reseting the ABS module in Forscan be worth a try and would the module need to be recalibrated if reset with Forscan. Thanks for your time.

[@TIMBHMAXX22]

hello, i know this is an older video i just found it but i am trying to reset the shift learning history on my 19 edge titanium ecoboost and using forscan the first time, is this a safe thing for someone to do? also, what is the difference between the connector that has the toggle switch on it vs without it? thanks

[@alexsavva9353]

Hi. Any ideas, My ford focus is locked on maintenance mode and i can not unlock it. Apparently i need to access the maintenance module on Forescan

[@jorlopez26]

Do you have to do the wire or pin swap on both sides, driver side, and passenger side? Also getting an error. I’ve tried the only Fxxx-xx since I have a 4key fob, do I need to use the FC code, tried without didn’t work then I did it with FC didn’t work. on the driver side and I’m getting a short ground error on the DTC on the driver module wires I had to cut a wire and resplice it wire a 3m connector. No errors on the passenger side module just on the DDM. What do you suggest?

[@sabahusen6842]

thank you,how to add navigation or change language?with scaner can do it ?thank you

[@SYDiagnostics]

There is plenty of info on a google search for adding navigation. Its not something i cover

[@AutoDiag_]

What adapter should i buy?

[@rustleinthebushes6065]

Hi Steve I have forscan , are you able to tell me how to disable speed limiter on a 2005 transit van at all please

[@leso204]

When both EGT sensors are changed do you have to do a learned value reset ,,,,,,,,,,,,,, Tia ...

[@SYDiagnostics]

ive only done that when the code has been set for over temperature during regeneration

[@leso204]

@@SYDiagnostics : thats what i have' had the P244D code come up only after a hard reboot for some reason , waiting for new sensors to fit , cheers ..................

[@SYDiagnostics]

if its a 1.5 ford diesel then there are a few things that can cause this concern. Non of which are sensors. with a cold engine do they both read 100 degrees?

[@НикМарк-д1д]

Does it forscan have injectors contributions test?

[@SYDiagnostics]

if it is listed then it will be there, but it mainly mirrors IDS and that is hit and miss on most vehicles

[@rickychips5022]

Im getting a few codes and after a search on the internet ive been told to use FDRS to update the pscm software. Can I update the software using forscan?

[@SYDiagnostics]

unfortunately not

[@roystynheath6533]

hi i have gone from sync 2 to sync 3 i got on ebay i have installed it most things work ok but i have no control on voice control on satnav have no sound from it also i have no dial tone on hands free i am getting forscan installed but don't know what to look for to correct it hope you help please..

[@SYDiagnostics]

I'd be looking on the forum for forscan. It's not something I can help with

[@joeblogs1169]

Hi what module do i need to access to tell the van to accept the new headlight bulb .‘I got no voltage going to the left hand dipped headlight light . I have been told I been this device to tell the van it’s safe to turn the headlight back on. Thanks

[@SYDiagnostics]

Not something ive heard of. Usually just replace the bulb and delete any codes (bcm) . Unless you have further issues with the vehicle

[@joeblogs1169]

@@SYDiagnostics thanks so much for taking the time to reply. I will try tomorrow in daylight. Just getting the laptop sorted . It should be law that a lighting circuit is basic and can be fixed by anyone at the roadside and not need a computer degree. The world has gone mad

[@leso204]

What are sync 1-2-3 ??

[@SYDiagnostics]

The different versions of the audio/media system ford use

[@leso204]

@@SYDiagnostics Cheers was told it was software generation , so just for audio and wont affect a scan just bought OBD cable and forscan so getting conversant with the tool before i attempt anything first , many thanks .........

[@shady4422]

Hi mate will forscan allow me to set the pat fluid as ive just refilled the tank

[@SYDiagnostics]

pat fluid??? what vehicle ?

[@shady4422]

@@SYDiagnostics c max 2006 tdci 1.6 i mean the dpf fuel additive the tank was empty ive filled it up but was wondering if i can use forscan to reset it

[@SYDiagnostics]

@@shady4422 its not a system ive worked on, but i'd imagine that it would be there

[@shady4422]

@@SYDiagnostics ok thanks

[@fords-max141]

min.delay 37ms not good !, connection : turn on Auto -increase :)

[@SYDiagnostics]

Can you explain what it is you are referring to?

[@NonnofYobiznes]

This is NOT what every button does because you "already explained in another video" 🤨

[@SYDiagnostics]

Calm down love.....thanks for the view

[@sukhmaidickoff]

Great video, thanks for taking the time to record and upload it. Personally, I have had so much trouble with my Forscan diagnostic tool. And now when it finally was able to connect to the car, it takes several minutes before it happens. It writes "No connection" several times before it then finally connects after a long time. In addition there are many modules in my menu where it says something like "not available" or not able to read - and there are red exclamation marks. Maybe it has something to do with the fact that my Forscan "unit" has a switch on the OBD-plug and that this is in the wrong position - I have to check that

[@CARRJ142]