Dude! I am going to fix mine!!! It's been driving me crazy! Thanks.
@sumcrazydude9 ай бұрын
Am glad you seen it, it was also driving me nuts lol
@llomax10679 ай бұрын
I'm doing mine this Saturday... Same... It's been driving me nuts
@liftedvibrations9163Ай бұрын
Thank you for making the video bro. Unfortunately my Chrysler 300s started to do the same thing and it’s been looking shabby in my eyes so I can’t wait to fix it.
@llomax10679 ай бұрын
Bruh used that 3m panel bond yesterday.... Let it set for 24hrs looks so much better... Thanks for making this vid brother
@sumcrazydude9 ай бұрын
Glad I could help
@kathynewburn270711 күн бұрын
What kind of glue? I cant get my panels off, im affraid they will break. Do you know anyone that can fix them in the omaha area?@sumcrazydude
@joeyh37393 ай бұрын
Thank you @sumcrazyguy I have the same problem with my 2017 Chrysler 300c....but its all the door panels.Im going to give this a try and I hope it works.Thanks again bro!
@curtisschneider99372 ай бұрын
Same exact car and issue, did you end up trying this?
@ynrt_5.7723 ай бұрын
Nice job....looks good 👍🏼 i need this done ASAP it looks bad.....thanks for sharing
@sumcrazydude2 ай бұрын
You can do it!
@kilroy25178 ай бұрын
As a Charger owner who had this problem, I have yet to find anybody that has used a glue/cement/epoxy that has lasted any significant time. The panel needs to be stapled into place to guarantee a permanent fix. This is the fix: kzbin.info/www/bejne/Zl6ofIajab6nZ7s&ab_channel=A.R.T.%27sRealRepairsforRealCustomers I did this 18 months ago and it worked perfectly. I bought a $30 staple gun from Harbor Freight and borrowed a small compressor from a friend. You can probably rent a compressor and staple gun for well under $100, and that's a bargain compared to the $1300 fix Chrysler proposed.
@sumcrazydude8 ай бұрын
Look at the time I released this video. That's how long it has been since I fix it and still holding strong
@kilroy25178 ай бұрын
@@sumcrazydude OK that's great, but that's only 5 months. Let's see if it lasts a year, through four seasons (if that applies to where you live) I'm not criticizing you, just sharing my experience. To anybody that uses an adhesive fix, good luck, I honestly hope it works for you. none of us should have to deal with this BS in the first place
@FrankCoit6 ай бұрын
Is it always the passenger side? My drivers side is fine, but the passenger side keeps coming off
@kilroy25176 ай бұрын
@@FrankCoit My passenger side went first and was so bad you couldn't rest your arm on it and you could see an inch of the white inside it from outside the car, then the driver side starting lifting, and that's when I tackled it. BTW, it's been about 18 months now since I did the fix and it still looks great.
@sumcrazydude6 ай бұрын
@kilroy2517 mine still holding too. It seems that glue runs hot and it molds the foam under the vinyl to stay in shape.
@reddyfreddy Жыл бұрын
thank you!!
@sumcrazydude11 ай бұрын
I figure yall needed this 🙂
@23lafamilia110 ай бұрын
Thank you
@sumcrazydude9 ай бұрын
Thank you
@BlackRifle00 Жыл бұрын
I’ve done this twice on the panel down by the shifter on my 300, and after a month it gives out. What specific glue did you use for the panel? I’ve tried 2 different plastic glues with no luck ☹️
@sumcrazydude Жыл бұрын
3m panel bonding
@lorifultzvanbeek2676 Жыл бұрын
Just curious what you used in the past that didn't work? I need to repair a charger panel as well. Was going to go with JB Weld until I saw this video.
@reddyfreddy11 ай бұрын
@@lorifultzvanbeek2676 I used gorilla super glue. ill post later if it fails
@pumam970910 ай бұрын
@@reddyfreddyhow’s it holding up so far?
@reddyfreddy10 ай бұрын
@@pumam9709 its holding up fine. otoh, my charger is a garage baby. *** gorilla glue ****
@SouthernGuy Жыл бұрын
I'm curious is the panel still holding? For some reason mine keeps coming back apart, but I used different types of glues.
@sumcrazydude11 ай бұрын
Mine still holding strong
@3swyndal8 ай бұрын
You can also use a heat gun to loosen material put clamps on it to hold in place the take a staple gun 3/8 staples to hold in place. Then putting epoxy on it to cover the staples then paint it.
@DaOnlyOneHere9 ай бұрын
Perfect🔥
@sumcrazydude9 ай бұрын
Thanks
@kathynewburn270711 күн бұрын
OK WHAT KIND OF GLUE DO I NEED? I WILL DO THIS WITH THE GORILLA TAPE AND A BROOM HANDLE.
@sumcrazydude2 күн бұрын
Body molding glue
@benjii7668 Жыл бұрын
Does the epoxy hold over time? Im hoping, this shit was $90 plus I had to get a gun.. thanks for the ideas in the vid....
@sumcrazydude Жыл бұрын
Yes it holds hard, I have left my car out in the sun for hours and still holds the shape.
@sumcrazydude Жыл бұрын
Also thanks for the support 🙏
@benjii7668 Жыл бұрын
@sumcrazydude used your idea last weekend on my wife's charger. Worked great, the epoxy seems super strong. I wonder if using a seam roller while the epoxy is drying would take out the divets. All in all it is a night and day difference, turned out great thanks...
@kathynewburn270711 күн бұрын
I am having a hard time getting the panel off. Can i fix it with it still on the car?
@sumcrazydude2 күн бұрын
I wouldn't recommend it but, if you protect all other parts that are not related to the panel, I think it can be done while mounted.
@michaelcornwell5575 ай бұрын
Cool another way to use duck tape 😂
@sumcrazydude5 ай бұрын
Lmao
@llomax10679 ай бұрын
My brother.... Is it still holding
@sumcrazydude9 ай бұрын
Holding strong 💪
@poco1174Ай бұрын
Don’t feel bad. Porsches do the exact same thing.
@joejohnson5748 Жыл бұрын
It loo great cn u do mine
@sumcrazydude11 ай бұрын
I could but it be cheaper to buy a new panel than pay me lol
@chareyscott70132 ай бұрын
My center console is peeling away idk how to fix it 😭
@madihuffman8947Күн бұрын
The plastic just pops out! I just resealed mine & it looks so much better. I got body panel adhesive and used clamps/ my hands
@badlilstang10 ай бұрын
Why not staple?
@sumcrazydude10 ай бұрын
Staples are not a consistent hold, eventually you will see where tha staple its holding
@elmono71411 ай бұрын
Where you located
@sumcrazydude11 ай бұрын
Am am located in the swamp lands of the Florida states
@wildroze778 ай бұрын
Wish you were in California
@robertfinkelman5493 ай бұрын
Try "peel" instead of "peal" 😂
@aronolejniczak52478 ай бұрын
TRIM YOUR NAILS MATE!!
@sumcrazydude8 ай бұрын
How else can I snort ma cocaine?
@STR8ADVOCATE4 ай бұрын
Lmfao
@mikepierre1245Ай бұрын
Dodge drop the ball no more dodge for me last time I buy cheap build American cars trash