Chinese ATV No Spark

[@troycork6802]

Got my bike going due to this video; legend thanks heaps. Not to mention I got the bike from a scrap yard got new parts for it did this video wiring and now running

[@georgegonsalves9961]

Mike!!! I have scaled KZbin for weeks now trying to get it to work. Your vid sorted me out and boom I got it running. 👍 thanks sir

[@mikesgarage9757]

Awesome! Sorry you did not find me sooner. Thanks for the reply!!

[@bobox6073]

Man eveytime I get a project and I always watch ur viedo again to rewire the 110cc motor and u make it so easy to understand . Thanks for the knowledge and keep making viedo u doing a good job .

[@mikesgarage9757]

Thanks I appreciate that.

[@Smalltechguy]

Man why didn't I find your video first...grrrr. This ATV of mine ran when I parked it. Cleaned it up and then no spark. I already bought a new coil and it still didn't work. I had to remove the plastics again to get to the other connections under the fuel tank. Finally I have spark again...Thanks to your video

[@mikesgarage9757]

Thats Awesome! Thanks for the reply

[@bobox6073]

Dade I buy a 110cc Chinese 4 wheeler. And it didn't run bad wiring and I watch ur video and I don't know shit about rewire 4 wheeler or bike . I did what u say on ur video and man it take me 15 minutes to strip everything down on a Wire and I rewire from scratch like you did and I put a kill switch and starter button on it and the damn thing fired up. Thanks u keep up the good job .

[@kenbeck8050]

Bought an old Yerf dog CUV rover…ran great until yesterday,,, no spark! Your video will help in troubleshooting. I am very familiar with the Japanese big 4 UTV’s and ATV’s wiring,,, these are bit different THANK YOU

[@bigjohn5104]

I have been going nuts with a customers 4 wheeler like that that someone else had destroyed the wiring on you saved me alot of headache figuring out what went were!

[@mikesgarage9757]

Thanks! I am glad it helped.

[@JBKUKI]

Big fan from India, Manipur state I really like this video I search this type of teaching video so today I get Really thank tou you bro

[@franklintyndal6986]

Thank you very much buddy I appreciate that you're about as easy as it comes whenever it comes to KZbin videos you can't get more basic than that good job man

[@mikesgarage9757]

Thank you . Sorry for the late reply.

[@frank1128]

Great video man. Helped me figure out my ignition switch was the culprit.

[@mikesgarage9757]

Awesome! Glad it worked out for you.

[@patrickfields2362]

@@mikesgarage9757 I used this guide today and it was perfect for what I needed. Where you have installed your "on" switch in the box, this is where we would wire in a momentary switch to get the bike started correct? Once the bike has started and the button is released, the starter will disengage and the bike will stay running until the kill switch is pressed using the center connector on the CDI plug. I want to make sure I don't keep the starter engaged and burn it up. Thank you man for the help.

[@mikesgarage9757]

@@patrickfields2362 Yes that should work fine. Glad it helped out.

[@patrickfields2362]

@@mikesgarage9757 Do you have a fix to be able to keep the battery charged with a shortened harness like this?

[@LWilliams42408]

Thank you so much. I appreciate what you just showed me. I was going nuts trying to figure it out..

[@bernardboles3641]

You are the shit ive been messing with this atv for months trying to figure out why i haven't been getting a spark and everyone else shows how to hook it up wrong and i thought why not try what this guy is talking about and boom i got spark finally wish i would have found your video sooner thank you so much im definitely subscribing and anyone who is in the same spot i was do what hes talking about theres no need to keep looking at other videos that get you no where 🎉

[@mikesgarage9757]

Awesome! I'm glad it helped out. I tried to get to the point. I see alot of videos on here that tell you how to do things but it's confusing when they explain it.

[@JesusRivera-wv5be]

the only part im stuck on is how he wired the switch that is between the poles. he said there is no magic there but i honestly know nothing bout quads or electrical wiring. can anyone help me out

[@otter5555]

thankyou, got spark in 15 minutes

[@donaldhalls2189]

Very useful, thanks for sharing, all the best to you and your loved ones

[@johnlester9929]

You sir are the absolute best I was about to bring it to the junk yard for couple bucks and but a new motor but this video helped a ton i can’t thank you enough for getting straight to the point and just telling us what you did very smart and saved a lot of time👍

[@mikesgarage9757]

Lmao Thanks Ma! I do apriciate it.

[@johnnispeling5633]

To the point, clear and no wobbly camera images. YOU ARE A ROCKSTAR!

[@mikesgarage9757]

Thanks Much Appreciated.

[@JorgeRodriguez-ei2gi]

Thanks Mr Mike keep up with these videos & wite harnes thanks ,Say hello Joe.

[@mikesgarage9757]

You got it

[@Motorhead24x]

This is an AC cdi circuit. With a DC cdi circuit you need a 12v input (not the red and black wire). If you hook up a DC cdi this way, you will fry the cdi box.

[@mikesgarage9757]

True, but this is for a Chinese ATV not a GY6. I have yet to see one different. not that they are not out there.

[@thatboiileroy_17fl75]

Thanks to u got mine wired up and running within 15 mins nice vid💪🤟

[@mikesgarage9757]

Awesome!!!! Glad its running.

[@babyfacebabyface8519]

Will there ever be a KZbinr that gets straight to the point without unnecessary comments that just take up time and interest!

[@dmacevoyf]

Great video, worked out to diagnosis the spark perfectly. Thanks

[@mikesgarage9757]

Thank you so Much for the Comment! I am Happy it worked out for you.

[@jallison22]

Best video on the subject….liked and subbed, THANK YOU!!!

[@remishernandez8783]

Man I'm not a video person myself and I have seen plenty of them but let me tell you you are the only person that really breaks it down the way it's supposed to be done I hope to see more of your videos and on top of that I have a situation with a moped that I cannot get no fire to and when I do it dies I don't know if it's the wiring I just don't know I've tried it all my friend

[@conorcavanagh4449]

Great video mate, helped me get my little nephews quad going

[@mikesgarage9757]

Thanks. I am glad you got it up and running.

[@antonioferreira2936]

N in

[@JorgeRodriguez-ei2gi]

Great Mr Mike,continúe thanks sharing Say hello Joe.

[@mikesgarage9757]

Thank you, I will

[@gala83filmstaylorg7]

Thanks man helped me out so liked and subscribed! Keep at it

[@mikesgarage9757]

Thanks for the sub! I am glad it worked out.

[@keithstewart526]

Thanks! The information was helpful!

[@mikesgarage9757]

Glad it was helpful! Thank you.

[@joshuabrown902]

You nailed it. Make more videos please

[@mikesgarage9757]

Should have another one up next week. Thanks for the comment.

[@Dazehead-ng8uy]

Omg this helped so much!

[@estebanmarquez6365]

Hell yea thx, couldn’t find out why i didnt have spark.

[@mikesgarage9757]

Glad it worked out for you Thanks! Thanks for the comment!

[@davidhughes4728]

,, thank you for the video it really helped me out a lot keep up the good work

[@mikesgarage9757]

Thank you for the Comment! I am happy that it helped you out!

[@saadiqrahim7849]

Thank you so much I am definitely learning soooo much through your teachings 👍🏿👍🏿

[@mikesgarage9757]

You are so welcome! I appreciate the comment and im glad it worked out for you!

[@kingrodai5323]

Thank you, buddy. Thank you, buddy, I have a question. Do you tell me what these wires do?

[@mikesgarage9757]

Which ones?

[@carboncopy6767]

Mike, I thank you very much for you making your videos. I struggled the whole day. We’re trying to find out why I didn’t have spark and the keyword you said in this video is check your connections and dog on it. If it wasn’t the connection I wish you well I hope you make plenty of more videos that simple with keywords thank you so much. 😄🫵🏻👍👍

[@gdaddy1273]

Easy explanation. Thanks, well done and to the point!

[@iamyzdemon5717]

Thanks for the video, and you can always kill any motor if you pull the plug wire off quickly

[@mikeking8059]

Yes you can. Thank you.

[@ballzmahonee5645]

Good way to get zapped. Better hold it back away from the plug. I've seen the spark jump 8-10 }inch

[@iamyzdemon5717]

@@ballzmahonee5645 I had a yamaha banshee that had no kill switch. I had the throttle get stuck wide open and I didn't wanna blow the clutch if I pulled it so that's when I learned the trick

[@codytaft9275]

Was helpful man. Appreciate it

[@mikesgarage9757]

Thank you! You are welcome!

[@allanrimington7862]

Thanks I under stood you straight to tha point.thanks

[@mikesgarage9757]

You are welcome! Thanks for the Comment!

[@andersondiazknight1493]

Thanks man it did work and just so u knoe no one got hurt

[@mikesgarage9757]

Awesome Man. Thanks for the Comment.

[@relevant1683]

This helps a lot, thank you!

[@mikesgarage9757]

You're welcome! Thanks for the comment.

[@toothlessboss]

Mike I know this video is old but I need your help I’ve asked atleast 20 people and no one know how to help but I can’t find my exact part mine has 3 wires plus the one for the sensor but when I look up the part I can’t find any except a 3 wire plus 2 wires I could really use your help I tried wiring your system up wire from wire but my magneto doesn’t have the same wires I wired each of the 3 up after figuring out which one ran the sensor but out of the 3 wires I tested all 3 with no clue which one to start with and still no luck Thanks for reading this and thank you for helping you definitely have my sub

[@mikesgarage9757]

Maybe its an AC system? Is it like this? www.ebay.com/itm/394752655168?hash=item5be9177f40:g:4sgAAOSwXIFkEOA0&amdata=enc%3AAQAIAAAA4Ff0Qv3UNGUqQmOf24esgkdXhlq196te9gW4seDSwJ8TimIZUShF0gEoL9cdVeDmPnxLq8MIhNOzNRCI3f0tMow8WhDSUIqHlXdefzhHz%2FwaMbtvOffFW3kgstzPAQUU5gE%2B6hC9pymGD3gE4VXI0rgLPUbjaIcNDyO46NcO1n%2FDOwdDtEQMWekcH9of1AwSVO09CzibLmHn2aNLg9rYlhedcKvV5V%2Bs6aCxIgEVttEwdk6j%2FQ2IgcQiXEh7J4rUjP09uOHy0Zvu8ZX8bWe5dFXT1vTOcGt6dUkiFnPi9o2B%7Ctkp%3ABFBMpsbonfdi

[@codyclark7916]

Thanks Mike .....you made it simple

[@mikesgarage9757]

Thank you I tried.

[@ericmorisky4122]

Thanks for this video 🙏

[@matttrantham1688]

Awesome video, found my problem, thnx

[@mikesgarage9757]

Glad it helped! Thanks for the comment

[@PedroGarcia-oj2xc]

Great explanation needed this

[@mikesgarage9757]

Glad it was helpful! Thanks for the comment!

[@johannsmit2001]

Hi there sir , Sir i have a gy6 scooter motor , i am confused . i have a blue wire , a green wire and 3 yellow wires ? green is for ground yes , blue i presume is the pulse . what are the other 3 yellow wires for? in sort i am busy with a off road project , I need a simple plug in push start button and off button wire diagram. ty for your content . straight forward no bullshit , Joe ,, South Africa

[@1johnhumphries]

Don't forget the ignition switch to as it was a new one had that problem.

[@LuisVazquez-lh2bv]

Beatiful atv engine is running thanks for your help

[@mikesgarage9757]

Glad it Helped. Sorry for the Late response.

[@LuisVazquez-lh2bv]

@@mikesgarage9757 thank you

[@barryjohns1965]

I am trying to get spark on a Chinese go-kart. I put the kit in it that has the new cdi, regulator, coil, and solenoid. I can get it to turn over but no spark. Every time I connect the hot wire back up it chirps loud two quick chirps. I have found the remote kill box and should be able to just unplug it to get spark. But still no spark. The neighbor owns it and list the fob. I sure would appreciate your input.

[@ongojay9965]

I was wondering if you can make a video of the wiring from solenoid to ignition

[@andrewchaplin9560]

did you find a vidd

[@xXdarkcloud47Xx]

Hey Mike thanks for the video but I got two wires

[@tfcthefamilychoice9374]

Good job man thanks my shitt work now I only pay 100 for one

[@mikesgarage9757]

Awesome!

[@Cody-ye3ye]

There’s 1K dude!!!! Congrats!!!!!

[@mikesgarage9757]

Thanks man that is awesome!

[@Cody-ye3ye]

Mike's Garage where do I hook 1 wire for kill switch cdi I weren’t clear enough

[@mikesgarage9757]

@@Cody-ye3ye The Center Wire that's not hooked up on the CDI Bottom Middle.

[@williamlynch6095]

I'm gonna go try it see if that works now if I do that and still no spark how will I know if it's the cdi coil or stator and what about the rectifier isn't it supposed to be in there somewhere please you have other videos on these

[@mikesgarage9757]

You would need to ohm out the stator. I'm sorry I don't have the values of what they should be. The Voltage regulator is for charging. You don't need it to run. I don't have any more Videos but I am planning on making some. Life has been crazy. Thanks for the comment

[@andbatr5167]

Can you do a more explanation video of how to check what causes no spark

[@daisymae8488]

Helped me alot

[@mikesgarage9757]

Thanks! Sorry for the late reply.

[@dennisbryan1149]

Good video . But what are the normal voltage outputs from the stator to the ignion box and from the box to the coil ? So the system can be tested for what component failed .

[@mikesgarage9757]

I have not done those tests, so I would not know. Sorry I cant be more help.

[@cheu1461]

Can you put together a video on how to wire up front and rear lights?

[@mikesgarage9757]

I do Plan on doing more videos of this bike, but it will be in the winter time.

[@vintagemotopros3955]

Good vid but....which bottom position to attach ground off switch? It looked like you were pointing to bottom right, stator black/red wire

[@mikesgarage9757]

Bottom center there is no wire in mine. just run it to a switch then ground.

[@vintagemotopros3955]

@@mikesgarage9757k

[@bigbudlover7930]

Great video

[@mikesgarage9757]

Thanks!

[@mikesgarage9757]

Thank you! I Really appreciate the Comment.

[@arvilmatlock7921]

I have 84 honda trx 200 with no spark can't figure if it's the stater,coil or cdi any ideals ?BTW good video

[@mikesgarage9757]

Thank you

[@gamingsteinpc6874]

OMG! Thank you so much! I got mine done!

[@mikesgarage9757]

Awesome Glad it worked out for you.

[@charleskee8796]

great video my stator has all the other wires but instead of black and red it has red no black stripe is that the same wire ? any help is very helpful ,thank you very much

[@mikesgarage9757]

Its hard to say. My "Guess" is it's the same

[@wespurcell3217]

Your awesome bud ty so much. Now if only I could get my floats right lol

[@mikesgarage9757]

No sweat. yeah the carb can be tedious on these china bikes.

[@phocthat]

Put it level with the botom of your carb

[@sterlingzeppenfeld1483]

Thankyou for your video! Very informative

[@mikesgarage9757]

Thanks Man.

[@martinalvarez3271]

Thanks for the video!! Helps out a lot

[@michaeldevitt5316]

Hi can you run the engine with the charging wires disconnected thanks Mike from england

[@richardwright8902]

Learned alot. Very good. But still can't figure out why I'm not getting fire on my switch.

[@mikesgarage9757]

I hope you got it. Thanks for the comment. Fire on the Switch?

[@williamparson7702]

Wish I seen this video 30 min's ago before I sold my kids go kart...I could have wired it up myself and kept it.

[@barrysunderland7262]

B p p popp ò o0 9 mlpno I'll jp9 no too lip 80😅p

[@dubbedmodz7253]

Thank alot sir!! Question? For kill switch I have a blue wire coming out of plug for cdi...is that the kill wire??

[@mikesgarage9757]

if its in the middlle probably

[@johnmpowell]

Great video! It really helped me restore one that had been left out in a field for years.

[@mikesgarage9757]

Awesome! Glad it worked out for you.

[@MichaelScott-t8v]

Yes what does that other Square black box that mounts under the seat do

[@MdRubel-nf9nj]

Nice 👍

[@mikesgarage9757]

Thanks!

[@ronaldbell2051]

Good video and theory to create spark. However, I believe you should also show the viewers where to ground the stator itself because you only showed how to ground the spark plug coil and cdi box. Otherwise, this method works because I tried it before I even saw this video and the quad started and I rode it down the street & then the stator exploded.

[@nicolec7290]

Very good video. Saved me a lot of time. Can’t thank you enough

[@sedaudie]

The one I was working on would start up and lose spark shortly after, I unplugged the remote start and now it stays running.

[@saltorres2027]

Good video but how do you test each mechanism in the system? I have a Panda Trail Rider 70 with no spark.

[@mikesgarage9757]

Sorry the bike is in storage.

[@patricktolmie1685]

I have a 250 Wilderness Trail no spark could you give me some information on that in a video thank you Patrick

[@phocthat]

Got the same does your brake light bulb is burned out ?

[@willanderson257]

Hey Mike Thank you for your videos they are very informative. I found a 110cc atv. I ordered, left and right brake handles. My question is, where do the wires go for each. Are they brake light wires? Thank you

[@mikesgarage9757]

Thanks for the Comment. I think one Side is for the Light and the other is for Safety Start. Where the lever has to be pulled in to start the bike.

[@Justamanonamission77]

Hey man great breakdown but how is going to help me figure out why I have no spark? Can you help me troubleshoot? New harness and did some welding on my frame but disconnected everything and removed stator. Any ideas?

[@mikesgarage9757]

CDI? did you disconnect grounds when welding?

[@JohnjcupKaanar-vy8gn]

Very hard to figure out. Ur smart

[@mikesgarage9757]

Glad it helped.

[@josephkewley2502]

I think a diagram would have help better, i think the cdi have more than 4 terminals to connect wires

[@mikesgarage9757]

I was going to put up a diagram but I thought the video covered it well enough.

[@Itsnotmyname1172]

Good man thanks 😊cheers

[@mikesgarage9757]

Glad it Helped!! Thanks for the Response! Sorry its a late one.

[@heliarche]

Hey Bud! Thanks a ton! Mine came to me just plain roached from a scrap cleanout. Looked complete though so I had to try. My CDI is a little different than the one in your vid but between You and a schematic, kind of splitting the difference, I got it sparking and running. Does that kill switch ground the ignition like an old magneto lawnmower engine, or does it kill the power to the coil?

[@mikesgarage9757]

Like a Magneto. I am glad the Video was useful to you. Thanks for the reply.

[@heliarche]

@@mikesgarage9757 Understood. Thanks!

[@michaelbennett9824]

Very very helpful thank you so very much

[@mikeking8059]

You are welcome. Thanks for commenting.

[@michaelbennett9824]

You’re welcome

[@robertmckinney4748]

Thanks man your a beast 💪

[@mikesgarage9757]

No problem 👍Thanks For the Comment!

[@triedtrue2277]

I Tao Tao 125 for free from a friend of mine for my son. I had it running good. Now no spark new harness cid box coil and i am still get no spark at the plug. suggestion?

[@Ryan_1997]

Going through same crap

[@radeburs294]

Hi thanks a lot you have help me im from bosnia but i have another problem i have now spark and fuel but it whant start

[@mikesgarage9757]

maybe it jumped time

[@2259chevy]

Hi can u show how to wire a rectifier

[@CayRome]

Kool video, subscribed, thanks

[@mikesgarage9757]

Thanks I don't make many videos. As nitro rc dude so kindly pointed out I don't have a good camera.

[@CayRome]

@@mikesgarage9757Quality is ok, most importantly, your content is excellent!!

[@mikesgarage9757]

@@CayRome Thanks. I am going to make an effort to do more videos.

[@thedreamteam4u]

I have power to my new stater and it's pulsing but power coming from my cdi to the coil.

[@Roberto-er5ow]

We used to just pull the plug out... manual shutoff 🤷‍♂️

[@mikesgarage9757]

LOL. Yeah i have done that.. Don't recommend it though. zzzt.

[@Random.Adventures.]

i liked and sub plesase more vids on chinese atv trouble shoot thanks

[@mikesgarage9757]

I will when I get a chance. Still Laying floors in my house.

[@Random.Adventures.]

@@mikesgarage9757 question are stators are interchangeable example if i have a 2 pole and i get a wiring kit with a 6pole stator

[@mikesgarage9757]

@@Random.Adventures. Honestly I can not tell you. I have not seen a two pole. Does your unit have a battery or is it just kickstart?

[@Random.Adventures.]

@@mikesgarage9757 battery but i got it thanks I just had to match up the stator

[@philliplockhart9643]

Awesome, its been in garage for 3 years the girls i got it for are into boys now so i guess its mine. That got the spark going, buuuut its makeing a popping sound just when its trying to fire. Any idea what that might be?

[@mikesgarage9757]

Sounds like a stuck valve, or maybe it jumped time a bit? hard to say. shut the gas off and put a little fuel in the spark plug hole and try it. if it fires off you may just have a fuel/carb issue. sorry for the late reply.

[@sergiojceballos2307]

Thank you so so much

[@mikesgarage9757]

No problem

[@robertlongley6115]

I have two boxes which one do I know is the CDI box the one under the gas tank or behind the gas tank

[@phocthat]

The plastic box is the CDI the metal one with heat sync is the voltage regulator for your lights

[@jasonclements4607]

THANK YOU!

[@paigevaughan3510]

I took the wiring harness and engine off a 200cc enduro motorcycle how can I go about bypassing the key ignition wires basically I'm tryin to figure out how to make a wiring harness out of the old harness that came off the bike it ran before I took it off but I cant get starter to crank and cant use kick start. Reason why I cant use kick start is because i swapped it on my 1985 Honda atc 185s and kick start cant travel far enough.

[@mikesgarage9757]

I am not familiar with that system. I assume you would connect the wire that pass power.

[@michaeljenkins3810]

I have a buggy I think it’s a spider 300 I need a wiring diagram if you can help thanks

[@bradstroke]

I am installing a remote start on a 125cc. I have got it to crank with the remote but won’t fire. If I put the hot wire on the top right, it should get spark right? I put this Wire on the accessory wire of the key switch, I get power to lights but will not make spark. I have put this wire on every wire on the the key switch harness with no luck.

[@mikesgarage9757]

I would need to know the pin out of your device.

[@bradstroke]

@@mikesgarage9757 I have a 5 wire ignition key and this is the remote start I am using. Saihisday Dual Remote Control Start Kill Switch For Chinese 55cc-125c Taotao Kazuma Roketa Sunl ATV www.amazon.com/dp/B078GGXK2G/ref=cm_sw_r_cp_api_glc_fabc_bXJZFbDJSH81S. This has the same wiring as you described in the video. I hope I have gave you enough info. Thanks