Citroen berlingo Crankshaft crank position sensor fault diagnosis and replacement FIXED

citroenberling...
/ cagmito76
How to diagnose, fault find and replace the crankshaft position sensor on a Citroen Berlingo , how to test if its faulty and how to change it for a new one. How to fix repair Crankshaft sensor.

[@giuseppebuccini6657]

Sei un grande... Mi hai aiutato tantissimo. Video ben fatto , chiaro e molto dettagliato.. i miei complimenti

[@dewindoethdwl2798]

Thanks buddy, exactly the fault I had. Rescued me from a big bill

[@cagmito76]

Glad I could help

[@paranormalrespectingspirit5190]

great video pal i am having issues with my car at the moment I have the Citroen Picasso 1.6 hdi 2008. I have issues starting her in the morning and runs like it's missing when it finally starts, sometimes it will cut out. Once the car is moving it will be fine for the rest of the day and start fine to. Would you say it is the camshaft sensor?

[@cagmito76]

Glad it helped

[@johndragonman]

im replacing the one on mine while i have the clutch and flywheel changed for a solid mass type. its 15 years old and for another £20 its worth doing.

[@cagmito76]

Yeah not a fan o dual mass not actually had an issue with one but dont like the expense

[@CiniMini69]

Great job mate. How did you check the wires? With a circuit tester?

[@cagmito76]

multimeter

[@CiniMini69]

@@cagmito76 thank you. I can't find the sensor on my car - Pug 406 2.0 HDi. Any idea where could it be?

[@cagmito76]

No sorry did you find it

[@CiniMini69]

@@cagmito76 yes I did, it's on the hearbox, under the airfilter box. All good, easy swap.

[@blackcastlerecords4802]

hi my citroen c2 1.4 8 velve engine .. does not spark only cranks but does not start tried to change the coil pack still wont start and does not spark .. is the problem the crank censor?

[@cagmito76]

it could be but it could also be a missing power or ground somewhere , or a computer burned out or a missing signal from another sensor depending on system . you need to do some tests to find out are you getting a trigger signal to the coil packs .

[@johncollins8676]

Hello where did you buy this sensor from pls

[@luisseguezza2323]

Domde esta ubicado el sensor del cuenta vuelta citroen verlingo 1.9

[@cagmito76]

this is crank sensor i dont this there is a cam sensor

[@ianpoulter3826]

This is the camshaft sensor, not crankshaft, the crank sensor is on the bottom pulley. I made the same mistake.

[@stevecummins324]

you sure? the sensor is on the clutch bellhousing... and responds to the teeth on the flywheel rotating past it... flywheel locked rigidly to the crankshaft,rather than the camshaft.

[@Droledope]

@@stevecummins324 : They can be on both positions, depending on car

[@stevecummins324]

@@Droledopeyes it's fequently the same kind of magnetic sensor for both crankshaft, and camshaft. If everything's perfect the signals will be in sync and have a known angle between them. But say timing belt jumps a tooth... That would change the anglular relationship of signals between crankshaft/flywheel, and that from camshaft. Similar applies if engine has variable valve timing. Having a sensor for both crankshaft and camshaft, allows values to measured directly, rather than needing computed as being relative to the other, with an assumption of anglular relationship between them.

[@blackfoot5527]

@@stevecummins324 camshaft is on top of the engine ,crankshaft sensor is always near the large toothed wheel of the gearbox ,the word says it self cranking, and not to be confused with the gearbox oil sensor

[@robharwood-stamper9857]

I did wonder. Having an issue with my Berlingo not starting after replacing serpentine belt.. no previous starting issues, so am trying to find crank shaft sensor location, as suspected damage to crank shaft sensor (suspected location behind crank pulley. still trying to find a decent video to confirm this)