Thanks for the video! Great job on showing how to do it and it’s clear.
@mshawnmhulett2 жыл бұрын
This is an awesome video. This helped a lot. Thank you
@shawndinterman22194 жыл бұрын
Really appreciate the video sir. Thanks for the info
@1320pass4 жыл бұрын
The good Bosch nozzles are hard to come by. Doing what Dave did here is usually better than the new stuff they sell. Sometimes those pintles are stuck real good.
@shannonscarbrough18273 жыл бұрын
9dd9
@shannonscarbrough18273 жыл бұрын
9
@shannonscarbrough18273 жыл бұрын
99. 99
@mplewis53884 жыл бұрын
Great video. Helps alot.
@brandonallan84873 жыл бұрын
Thanks for this video, it helped alot
@AllAmericanDreamChaser3 жыл бұрын
Great video!
@DannyRossa Жыл бұрын
Very good video! Thanks
@bwagenberg2 ай бұрын
ZOOM IN !!! Good video.
@ugotsmacked13 жыл бұрын
Thanks buddy. Just did them today. Had a genuine bosch set that came out when I got the truck, would be hard starting. When the bosch in the truck get bad just going to swap them out. I knew their wasn't much to them but I didn't want to attempt without a good video lol.
@JRRODZZ3 жыл бұрын
Did it fix the hard start just by cleaning them?
@ugotsmacked13 жыл бұрын
@@JRRODZZ yes, fixed my issue because I had 2 nozzles that was gummed up and sticking. . Ended up buying a bunch of other goodies and a new bosch set from quadstar.
@svtelos47262 жыл бұрын
I'll bet Hoppe's gun cleaner would work well. I use it on Aircraft engine nozzles.
@antilortiz23023 жыл бұрын
thanks for this video I have question wath type fluid you use fro clean
@jchambers25864 жыл бұрын
Good video buddy
@ding09254 жыл бұрын
thanks..
@steve197453 жыл бұрын
Ive got the same Bosch injectors its quite possible the truck did run like the guy said i had to change my injector pump so my truck sat for 2 months during that 2 months my nozzles got stuck on all the lines i completely removed.
@rra0220012 жыл бұрын
Appreciate the video. I have a 65 that for whatever reason, will only blue smoke once I get passed 40 MPH. If I stay around 35 to 40, no blue smoke. When it fires up in morning, no blue, white or black smoke. I am hoping its injectors or timing and not valve sleeves/stems and related valve body issues.
@adenseay7406 Жыл бұрын
What was it
@stevenbean97063 жыл бұрын
When i try to reassemble injector it doesnt thread securely against orange gasket. Is there a right side up or down on those shims you assemble it a million miles an hour i cant see the way the shims are going in ive tried a bunch of combinations but cant get it to tighten down
@michaelmounts1269 Жыл бұрын
nice video! are you able to check pop pressure when you’re done?
@michaelmounts1269 Жыл бұрын
grest video! any tips on where to buy pintles snd shims??
@thomasgellos17324 жыл бұрын
Got one of those 6.5's from 20 years ago, I ain't getting rid of it, even with inflation
@thomasgellos17323 жыл бұрын
@Camden Elijah Ford and Dodge folks don't care
@texassingh1027 Жыл бұрын
What tool did you use to remove the injectors? Need to do the same for my humvee.
@luispina4012 Жыл бұрын
👍👍
@johnbrooks2122 Жыл бұрын
I change a set in mine and now mine has 1 injector that has gas coming out were the top part screws to the big bottom and my truck is smoking worse idk what to do any help ud be a life saver ?! God bless
@terrellscaife241110 ай бұрын
Do these have injector cups?
@tonyknuth12564 жыл бұрын
How tight do you re-tighten them ?
@joeyforristal7545 Жыл бұрын
Little late but 50 foot pounds 😂
@jasonriggs41983 жыл бұрын
OK I have a question I have a six to Detroit non-turboThat rough idle loads up on fuel and white smoke smells like raw fuelCould this be stuck injector or most likely injection pump
@mshawnmhulett2 жыл бұрын
I would have to say injection pump. You need to make sure it is adjusted correctly
@johncountz80577 ай бұрын
Injectors stuck open or leaking will cause white smoke. Running it that way can melt the pistons...
@brentfff4601 Жыл бұрын
Is there a torque for putting the two parts of the injector back together before putting it back onto the engine?
@SEDHACARREPAIR Жыл бұрын
guess as long as it dont lrak , we see them outside
@brookewoody86204 жыл бұрын
did you have to crank it for a while to get it to start after the work
@mshawnmhulett2 жыл бұрын
Pull the glow plugs to prime fuel up. Not as hard on the starter and injection pump. You will see a mist start to for up the air, you will think it is smoke but it’s mist. At that point put glow plugs in and fire it up
@mikelknight7992 жыл бұрын
what you use for cleaning solution? and why you soak in thinner after cleaning??
@xexjukebox732211 ай бұрын
Ultrasonic cleaner, you get solutions that you dilute into water, and for the thinner, it's to dislocate any water left in the parts, as water is not good for any engine
@Ben-Dedia3 жыл бұрын
good viedo but they are 2 shims there witch one gose where one is more soild and other is more think and have some groves wish video was more clear thanks again
@johncountz80577 ай бұрын
The thin one goes in first then the thick one then the spring... The spring can rotate and damage a thin shim if you do it wrong. Also, make sure, you have fresh clean diesel fuel to lubricate for reassembly.