Clean the diesel fuel injector

[@florinelitu-lambrache9659]

Congratulations for the 608k views after all criticism.That's most important,right?Don't matter what you post.

[@karolisastrauskas3701]

Why electromagnet isnt torqued properly? And from video in the end, it leaks very badly, you can melt piston with that dripping

[@paulandrewpimentel2005]

Como 'Speedy Gonzales'- 🤣... Good Job, Man!

[@hollows61]

you are aware the calibration of this injector is now completely up the left not only by stripping it down but by all that aggressive banging on machined surfaces and sanding the main spool needle just because diesel squirts out doesn’t mean it performs as it should

[@dieselsolution]

Absolutely 💯

[@sebastijano]

Which brand ultrasonşc cleaner is good İ try vevor but i am not happy with it ;)

[@Bayuhutamamotor]

Cleaning The Diesel fuel injector, thanks for sharing successfull always

[@maskoko76]

Cleaning The Diesel fuel injector, thanks for sharing successfull always 👍🙏

[@serunaiserunai5215]

Any boby know what kind of a cleaner he use for, there is a foam, carb & injector clener and wd40 not like that...txs

[@technicalsupportfortestben4802]

what the technician does is a simple cleaning of the injector, he is not repairing it. I don't even check the control valve. An interesting video for those who are entering diesel electronic injection. but a long way from a professional job of remanufacturing an injector

[@MariusFourie]

How to F up an injector 101

[@matui6983]

Ive been reconditioning injectors for 30plus years and there is no possible way that engine ran fine after they were attacked like that video shows. No lapping of faces Wet n dry to polish parts When "tested" it "atomised"at an incredibly low opening pressure and was dribbling/leaking fuel out. Again....no way that engine ran fine on those injectors after being buthcherd like that. Holy shit is all I can say

[@Trenscendent]

Are these piezoelectric injectors?

[@ssss-df5qz]

@@Trenscendent judging by the location of the leak off, I'd say they were.

[@wallamboklahong9125]

If such aggressive way is to clean the fuel injectors, then how are we to control man made climate and darken polluted air a cleaner environment, I think these mechanics and engineers are not at all aware of the clean air and atmosphere.

[@Diesel8290]

Oh get of your high horse, the guy is working with what he has got. He even says on one of the other comments his circumstances Only enable him to work like this.

[@lissettelopez8331]

Any suggestion on reading materials that teach the best rebuilding process? I've searched Amazon Books and didn't come across anything. I'm trying to rebuild mine, and KZbin seems to lack a lot of info on diesel injector rebuilds. Thanks!

[@slmlogistics2224]

This is how we Nig-Rig, keep up the good work 👍🏾

[@ukraine345]

is it true that adding atf to your diesel fuel will clean your injectors?

[@RanjitSingh-h8b]

Good work 👍

[@h77]

@@RanjitSingh-h8b Thanks

[@andrewallen9993]

Using the highest standards of cleanliness and precision measuring, disassembly and reassembly tools an excellent job is done of not reconditioning these common rail injectors!

[@donotinvite]

sandpaper and cleaner do all the job

[@donotinvite]

and you can check complety ruind injector in the end of video

[@rustleinthebushes6065]

kzbin.info/www/bejne/f3nWqIWGZth3gpY

[@rustleinthebushes6065]

My refurb is better 👍 kzbin.info/www/bejne/f3nWqIWGZth3gpY

[@sebastijano]

What type off sand paper does he use

[@tazba5551]

If you are taking an injector apart like that you need to use an ultrasonic cleaner along with a carbon cleaning formula. Wd40 is not built for this

[@jonathanbadilla8756]

Good job. What kind of liquid do you use to clean them up? Is it gas, diesel or alcohol?

[@akosiya7160]

He's teaching how to buy a new injector assembly ahaha

[@vishalsahani154]

Sir naya injecatr kitana me melega ertiga vdi ka

[@TheMrBennito]

Good to read the comments. Summary: this isn't the way to clean diesel injectors

[@Trenscendent]

Is this a piezoelectric injector?

[@BuilditUK]

I'd be interested to see those injectors put back on what ever car they came off of and see how well it runs after. clouds of smoke I'm guessing

[@diesel-technology5507]

when he gets the abrasive paper on it though to give it a "clean"

[@rustleinthebushes6065]

Shocked in how poor this video is compared to mine kzbin.info/www/bejne/f3nWqIWGZth3gpY

[@enriquecamposrodriguez2916]

..

[@petpara]

hahahahaah this how u dont do it, specially whit the all the sensors in new cars, this maybe works on Golf 2

[@kevinhancock4064]

@@diesel-technology5507 not sure about using sand paper period bit I'd say that's a very high grit

[@TRUCKDRIVERKSA99]

Malinis na malinis gumawa si idol

[@nukultantikul1735]

I put w40 mixed with diesel in the fuel tank. to clean the injector?

[@serunaiserunai5215]

Intresting, is it work.? usually I mixed with JASO FC oil like castrol 2T.

[@TheUltimate65]

Good work, fore next time of cleaning of injektors, can Tunap 989 been used...im recomandet this product..😊

[@h77]

🤣

[@SelvaRaj-ml3jv]

Sir Ian having toyota etios diesel car 2013 model.in my car 4th injector blocked.where I can clean.i am in virudhunagar.tamilnadu

[@TRUCKDRIVERKSA99]

Galing talaga ni kabayan gumawa

[@SeiklusedSilluga]

viimastel sekunditel näha, et ots lekib, kui kole :D

[@wepipe]

Apparently Indian back-street auto mechanics have an immense topological resistance to chemical toxins but limited supply of gloves and microfiber cloths ?

[@MannyAguilarJr]

Correct

[@Moravia13]

They are like rats

[@nanau2002]

Said a random pale guy

[@techkushan470]

What spray u used for cleaning

[@sebastijano]

Couldnt find it

[@forqanrkik1355]

لا يوجد فتحات عندي في رأس ال Injection ما السبب

[@h77]

حاقن الوقود يحتاج الى تغير الكربون يعمل على اغلاق الفتحات

[@Anandrajput234]

Injector repair ma Kitna kharch lagega par injector

[@MaanDIESELLAB]

You are Great sir

[@333oberon]

The purpose of this video is so you know how it should not be done.

[@h77]

hahaha

[@sudinebabz8651]

Safety with gloves ✨👍🏼

[@timondadilaadila2275]

Are they work it or just taking risks? I can't afford new injectors

[@h77]

After cleaning, they work fine Good You may need to change some parts and then it works perfectly

[@gopalakrishnadoddi4869]

thank you brother u done a good job for cleaning of crdi injectors and i have a doubt that is how much voltage is given for injector testing please inform me

[@h77]

12 volts AC

[@kiviKatKa]

@@h77 way less and they run on pulse system

[@philbertnestorytuna9833]

I like your style

[@h77]

Thanks

[@GfdaaAadfg]

متى يتم عمل صيانه البخاخات الديزل

[@MaanDIESELLAB]

Your video always great

[@anwarhrahim9659]

Polo gt tdi de injector poyaal ith pole clean cheythu ittaal ready aakumo?

[@abdul_basith.v]

Poyaal nadakkilla bro...

[@ssss-df5qz]

Holy cow, look at that dribble 😄

[@jellainerivera6429]

Hi.gud morning San Po puede mag pagawa San malapit Ang shop Po no inyo

[@kofijoe5553]

Do you work on heavy duty tractor nozzle injectors too?

[@pliesJames]

very important to know this

[@ionelpatrunjel5536]

But the injector was leaking on the test bench.

[@sancolorado]

Alot of fuel consumption problems😤😤😣

[@Stomping-On-Roses]

You just know when there is a logo saying Hussein Car in the video that legit information is provided

[@funnyvideos6542]

I wonder if that guy washer his face with the liquid or uses the liquid as a mouth wash

[@xXJusTMichelxX]

I took an injector off to clean it and now the car is not starting, all the injectors are not spraying, there is pressure in the rail but the injectors are not opening. Help me please

[@popescugeorge4339]

I am not pro or against this procedure. Obviously the environment is not that clean and the tools are not that high tech but what I can say for sure is that what you are seeing here as a leakage comes from return port of the injector. So the drops of fuel come from return port of injector not from nozzle... My opinion ...

[@h77]

Finally, there is someone with a positive view of work If people knew the conditions we live in, the lack of possibilities and the high cost of living Yes, I work in a simple and primitive way because of the difficult conditions in my country My country is full of conflicts, problems and lack of services Even the Internet is intermittent, and the interruption may reach more than a full month My country, Yemen, is going through its most difficult conditions without electricity, services and a shortage of medicines I'm working to be able to Thank you for this nice comment and your words are correct. Diesel drops coming out of the return hatch

[@joefajardojr3902]

100%leaking injector after dismantling, it has to be change with new nozzle once you dismantle

[@maianbaaii]

ok🤣

[@daniloperonce6456]

My car is Ford range trekker model 2010. It was recommended by repair shop, to replace 4 enjector, but only by swapping. How much the 2nd hand ejector? How about the new? Ty good eve.

[@therealchayd]

You can pick up working used injectors from a scrapyard for not very much. New injectors are expensive. You will need to program the ECU for the new injectors after you install them otherwise the engine might not run right (I used FORScan (free software) when I replaced the injectors on my Dad's Ford Transit).

[@stephenlockwood8882]

Why did you not put the ball bearing back in the injector then at 07:00 mins it just disappeared 😀

[@dieselsolution]

If you follow them you're dead my friend

[@beowulf885]

was a bubble.

[@michaelroloff2804]

It may well be that the engine with these injectors ran again afterwards ... but certainly not, as the manufacturer aimed for! Why for heaven's sake rub around with sandpaper on parts that are made on Micron, I don't understand. Gloves? You can do it, but you don't have to ... are only petroleum derivatives! Hey, with all the love I have for craft activities, but the number here is something from the horror cabinet ... please add the heading with "You shouldn't do it that way!"

[@NhatCoKim]

Bàn cân kim đẹp quá

[@rockybalbao5004]

precision engineering vs caveman with WD40 and dirty cardboard... - still leaking

[@mialiu4548]

This is a great and easy to understand video

[@tamasadam1932]

Good example: how to destroy your engine :D

[@Commonrai]

Por tacaño te quedó gotiando trabaje para nada,por qué no le pusiste una puntera nueva y el vástago todo el conjunto nuevo

[@bongheng-hx3bv]

ល្អ

[@ernestoblock9080]

Podes mostrar Cómo marcha en el vehículo lo que reparaste?

[@h77]

el coche anda bien

[@ernestoblock9080]

@@h77 😂🤣

[@diesel-technology5507]

some poor soul has probably paid this chap to absolutely ruin their injectors

[@FranciscoFernanfo]

Eu lavo sem maquinas e sai em perfeitas condiçoes

[@h77]

👍

[@stivenrojas5239]

Nunca lijen la punta de los inyectores

[@brianpaige4884]

Never seen injector come apart that easy....

[@Jean-vz8co]

It exists an nozzle injector called '''annular spraying''' who gives a beter resul than the holed nozzle........ and it accept a low presure.....

[@electricalfive2248]

This is why KZbin needs to put the dislike button back. Ill bet some people will think this is ok, but injectors are no joke and have very tight tolerances.

[@fritzfromswitzerland]

My 2kd engine knocks very loudly when it is cold... Do you think cleaning the injectors will solve the problem?

[@SwampMyster]

No

[@h77]

I don "t think so Check the fuel pump sensor

[@fritzfromswitzerland]

Ok thanks for the advice. Do you know how to check the sensor? Should i change it?

[@SwampMyster]

@@fritzfromswitzerland dynamite will fix the problem.

[@m721ac]

@@SwampMyster the problem is your face...

[@sam40901]

Cheapest electromagnetic stimulator is a 12vac 5amp xformer.. attach one rectifier and footswitch will give you 30cps of pulse...it works..enjoy.

[@ssss-df5qz]

Except that isn't an electromagnetic injector

[@serunaiserunai5215]

same thing, i use dc 12 v 5A attach to arduno board, to make sure i had check with scope before attach to an injector, than inject hand hp pump, unlucky broke my injector selenoid...should not...i dont know why...

[@hansronny461]

Show how you test the injector you play you uncompleted movie

[@akosiya7160]

See that? Haha those are busted nozzle tip.

[@andreinicolaiamadeo3453]

@3:41 What the crap?!! Why did you use abrasive paper?!

[@AngelSanchez-jh5tz]

Que locura hacer eso en ese ambiente y usar papel de lija para limpiar, jamás será el mismo inyector. Pobre cliente.

[@Phil450]

Engineers need years to develop a good working injector and then there is this dude who cleans it with WD40 and sandpaper. I bet the car didnt run at all after that "rebuild"

[@h77]

I have a video and it works fine

[@electricalfive2248]

You're out of your mind if you think using sandpaper on the insides of an injector is good idea. Even 2,000 Grit is too aggressive for anything in an injector.

[@piecetoyou8285]

should be called how not to clean a injecter if you want your car to run after

[@h77]

Hahahahahaha

[@ciprianchelaru8720]

Nu functioneaza bine nu trebuia sa dai cu hartie abraziva, ai micsorat diametrul exterior al axului...

[@drewmurray2583]

this is why we need the dislike counter back!

[@zulqfly2383]

How to set it up if pressure isn't enaugh

[@h77]

Change the fuel injector or change a complete spare part

[@zzzzzzz6666]

Good woork 👍👍👍💕💕💕💕💕🌙🌙🌙

[@h77]

Thanks

[@Ihaveanamenowtaken]

The injectors were ruined.

[@نسماتالشام-ت5ذ]

لايصلح هاذا الحاقن ابدا هاذا هراء ولا يمت للمهنة بصلة العيار والتنظيف والعمل الصحيح لايكن هاكذا مطلقا انت مجرد هاوي لا اكثر ولست من اهل الاختصاص

[@cesarjorgemurillobarientos1813]

good

[@fernandofonseca2033]

This must be a troll video. Everything seems wrong here. From washing hands with gasoline to the way he hammers the injectors and polishing internal parts. I wouldn't put those on my car for sure.

[@travismari4157]

Just wingin it lol took my tonka apart last week

[@loibui2398]

Ok.👍👍👍

[@mattyP_7428]

His brother is a brain surgeon

[@h77]

Hhhhhhhh

[@juliusvergara7907]

What is that chemical you use to spray the injector? Thank you

[@abdul_basith.v]

Carb& injection cleaner

[@mikeelkhoury259]

benzin

[@serunaiserunai5215]

I don't think so, the carb & injector cleaner doesn't contain foam...it's like there is a mixture of detergent...I also want to know what kind of solvent to use

[@khudhayral-gaid6045]

اخي العزيز

[@saeedtavan2259]

روش بستنتون مثل بندس،تنها سنباده زدنتون اشتباس

[@eddiekilby]

Its leaking by.

[@ismaeldossantos3296]

I was doing that when i was 15 years old, i am now 69, i don't think that the new generations mech,s don't know how to do it.

[@MShodikin-f3c]

Ketika di coba akan bocor karena di amplas😅

[@h77]

👍

[@nolegator8745]

Obviously no one Commenting about toxic chemicals and etc doesnt know what its like to live in one of those broke ass places to understand how high in the important list cleaning his hands with diesel is to this man or how important exact tolerances are for that matter. I bet them injectors work better after "cleaning" them lol

[@h77]

Circumstances forced us to work this way and not take precautions in handling materials and diesel without wearing gloves Lack of capacity and lack of services And the conflicts in my country

[@ШерзодИсаков-ю9я]

💯👍🏻👍🏻👐👐👐👍🏻

[@boltthrower3215]

Muslim expert at work…soon in your neighborhood too

[@Liveforeever]

He's ruined that injector

[@xp62530]

ч-чистота. главное в работе с топливной. фильтры по 2 микрона там...все такое. я в ахуе от работы на картонке и отсутствию ультразвука, но в целом интересно конечно

[@paulwisdom5383]

There is so much wrong with this video I don't know where to begin

[@nhlanhla_magz928]

Its dripping 💧

[@marcelocaliva802]

Buenisimo

[@faraisamanjeyese6172]

I think something is not right on this particular video