How to bleed the clutch on 2013 Nissan Juke easy way
Пікірлер: 42
@stevefournier19014 жыл бұрын
Thank you, I was trying to figure out how to use that bleed whole. Much appreciated.
@niallcosgrove Жыл бұрын
Thanks for posting this. Worked a treat on our Nissan Tiida 2007. Its not identical but works on the same principle
@brettwatson-will3388 Жыл бұрын
Thank you for posting this... My 2013 Australian delivered Nissan X-Trail with the Renault 6 Speed Gearbox has this setup also... It worked a treat.
@anarasii Жыл бұрын
👌👌👍
@maxwellkaan3 жыл бұрын
Thanks for the great video and clear explanation, much appreciated
@anarasii3 жыл бұрын
Any time 🙏
@signummotors2 жыл бұрын
Normally I'd say it'd be better to bleed it into an empty bottle and add fresh fluid - but for the ease of it and speed of bleeding the clutch - I'd say it's a good way to bleed, since the end of the pipe is in the reservoir, you don't get any air coming back, only fluid if anything. After it's done you can always just replace part of the fluid in the master cylinder tank anyway, so definitely useful stuff.
@ademirlima57884 жыл бұрын
Obrigado por compartilhar, tinha dúvidas sobre o procedimento.
@extasynord2 жыл бұрын
tank you, very nice explained
@fucel912 ай бұрын
Dziękuję za uratowanie życia!!! Pozdrawiam z Polski ❤❤❤
@ruubguus43213 жыл бұрын
From 🇲🇽 gracias!!!!,👍
@leonardofelix41043 жыл бұрын
Muito obrigado salvou parabéns pra vvcs
@davedangerous Жыл бұрын
The clip and connector likes to stick. I lubricated Nissan Tiida 2008 with spray lubricant and it loosed up. The clip pushes down while you pull the connector sideways. I did the same thing with my Nissan Almera 2013 clutch and the connector pulled completely out and dropped the entire master cylinder brake fluid on the ground. The clip does completely different things on different models. The almera clip is totally sheit to say the least.
@mirjunior98646 ай бұрын
Well explained, useful video. Especially the trick how to press the metal pin in order to open the bleeder. I knew how to do it but I couldn't open it. After watching this the cluch fluid is replaced in minutes. Many thanks!
@anarasii6 ай бұрын
Any time 🙏
@arturdoko90115 жыл бұрын
Hi o my scenic2 is problem ,what to do??
@MohamedAlnaas-zd1tg9 ай бұрын
Thank You!
@AzizAllam4 жыл бұрын
Thanks for the video Aziz
@anarasii4 жыл бұрын
Mar7ba khoya
@AzizAllam4 жыл бұрын
Shokran video help me fix my car
@FASTU-mz3tm Жыл бұрын
yeah thas about it, only thing i do diferent is not blead it into the brake reservoir, so it dont contaminate the brake fluid on the brake system......................................
@laserr100000003 жыл бұрын
Thanks a lot
@jessezass3 жыл бұрын
Cool, thank you very much. I was looking at the procedure on AllData and about to have an anurism.🤬
@anarasii3 жыл бұрын
🙏
@mistrybipinkumar52722 жыл бұрын
Meri duster m kabhi bhi clutch kaam krna bilkul bnd kr deta h to kya kre??
@MRTuning7042 жыл бұрын
My cluch peddle went to the floor and I went to install a new master and bleed it and noticed I’m missing the clip 😭
@cultusgti2 жыл бұрын
Thank you
@anarasii2 жыл бұрын
🙏
@simrankabli50233 жыл бұрын
When I put in the second position it doesn't lock, because after the bleeding there pressure on the clutch and when I press on the clutch pedal it unlocks and get on first position. Can you give me any advice to how to lock it properly so that it stays on first position
@jonsalemi54343 жыл бұрын
hi, did yo find a solution to your problem?
@bmwm5bmw610 Жыл бұрын
Why you bleed it did you just replace the slave cylinder that's why ??? My slave cylinder is leaking inside gearbox what should do is there any chance of stop this leak 🤔 thanks