Coin Doming Tool Set - For coin bell tops, buttons, beads, crafts and more

This video demonstrates how to use the Coin Doming Tool Set by Legacy Brand Coin Ring Tools
Our new coin doming tool set for making coins into domes for coin bell tops, coin buttons and coin beads. Domes all sizes of coins using your existing 17 degree / 25 degree / Swedish Wrap Die sets.
Please measure the outside diameter of the dies you are intending to use. There is some variance in the OD of all brands of dies. This doming kit is machined with close tolerances to fit dies that are 44mm / 1.75" inches. If your dies are larger than 44.1 mm, please contact me via convo so I can customize a doming lid for you.
Three different sets available. Please read descriptions below and select the set you want from the drop down menu.
TYPE 1 SET includes:
One centering lid with a one half inch (1/2") deep recess that fits atop all brands of standard 1.75" diameter folding / reduction dies. It also works with Swedish Wrap dies.
Three domed DELRIN forming pins with approximate diameters of 3/4" inch, 5/8" inch and 3/8" inch. These pins are replaceable as needed, so you don't have to buy a whole new doming set.
Three 3D printed ABS spacers to adjust the depth of the punch recess as needed.
One 1" inch long accessory pusher for extended pushing of the domed pins inside Swedish Wrap dies.
TYPE 2 SET includes:
One centering lid with a one half inch (1/2") deep recess that fits atop all brands of standard 1.75" diameter folding / reduction dies. It also works with Swedish Wrap dies.
Three domed STEEL forming pins with approximate diameters of 3/4" inch, 5/8" inch and 3/8" inch. Steel pins are made from heat treated 4140 tool steel.
Three 3D printed ABS spacers to adjust the depth of the punch recess as needed.
One 1" inch long accessory pusher for extended pushing of the domed pins inside Swedish Wrap dies.
TYPE 3 SET includes:
One centering lid with a one half inch (1/2") deep recess that fits atop all brands of standard 1.75" diameter folding / reduction dies. It also works with Swedish Wrap dies.
Three domed STEEL forming pins and Three DELRIN forming pins with approximate diameters of 3/4" inch, 5/8" inch and 3/8" inch.
Three 3D printed ABS spacers to adjust the depth of the punch recess as needed.
One 1" inch long accessory pusher for extended pushing of the domed pins inside Swedish Wrap dies.
Free Shipping available on the Legacy LLC Site, no minimum purchase required
coinringtoolsllc.com/product/...
Also available on Etsy for International customers
www.etsy.com/listing/64971870...
Order yours today, and get your dome on...
If you are just looking for replacement doming pins:
Free Shipping available on the Legacy LLC Site, no minimum purchase required
coinringtoolsllc.com/product/...
Also available on Etsy for International customers
www.etsy.com/listing/69202738...
DIES and COINS IN PICS ARE FOR DEMO ONLY. NOT INCLUDED WITH DOMING KIT.
Legacy Brand Coin Ring Tools are all MADE IN THE USA
Thank you for watching, and happy doming..

[@tommygunss4576]

I just received my coin bell tools and love them. Thank you!

[@JTCoinRings]

Legacy Brand is making great products. I would definitely like to have this set. Thanks for sharing.

[@errolsavage9897]

Great tool.! Next on my list of press dies.!😜👍 Great video

[@frankkelly1433]

Gary very nice. the tools look professional.

[@legacybrandcoinringtools2956]

Frank, Thank you very much. The tools work very well, and top quality indeed. After many domes being formed using a variety of coins, these still work like the day they were added to my arsenal of tools... Gary

[@michaelthaynes5252]

You're right Gary, this is an "excellent" set for doming coins. I'm so happy that I got them from you. Going to purchase the swede die companion for the bell coin. Hope you make a video on using this. You teach well. Peace.

[@legacybrandcoinringtools2956]

Michael, Thank you very much. Glad you are enjoying the doming set. Here is a link to part one of the video made for the Swedish wrap set kzbin.info/www/bejne/jouVpat3psRonrc Enjoy, and happy ringing

[@michaelthaynes5252]

@@legacybrandcoinringtools2956 Thanks Gary , have been tuning in to it.

[@donelings8505]

Nicely done.

[@legacybrandcoinringtools2956]

Thank you Don, appreciate that.. Gary

[@tommyreimrock8667]

dapping blocks would do about the same thing I assume.?

[@weatherill430]

can you make a video of the bell makers die on how to use it ?

[@rlin2648]

If I want to start off just making half dollar bells what tools do I need first other than the Arbor press and punch set? Thank you

[@legacybrandcoinringtools2956]

See standard doming set, and 17° dies is the way to go to begin. If you want to save detail delrin set works very well, however the steel set is great and will last a long time.

[@ronalves9118]

Everything looks great. My question is what type of hydraulic press do you use? My Harbor Freight 6 ton press does not have enough clearance to place those tools in there, ( I think) I know that I can not get my Jason Works coin punch in the press. Thank you

[@jessegoodrice4208]

These are amazing I’ll be adding them to my setup very soon! Just a quick question, can you form silver coins with them and a 1ton arbor press or ring sizer?

[@legacybrandcoinringtools2956]

A one ton Arbor press will work, however you have more control with a hydraulic press, and yes they will form silver.

[@dodge6002]

How can I purchase a kit like this and if so what would I need for a beginner. Thanks

[@legacybrandcoinringtools2956]

Hilario, Thank you for your interest in the doming tool set. There are links in the description below the video to the doming tool set. Here is the link if you are having trouble finding it coinringtoolsllc.com/product/coin-doming-tool-set/ If you are looking for a beginners set for coin ring making, Legacy does also offer such kits on the site the link will lead you to. If you need further assistance, or have questions, feel free to send us a message on the LLC site contact us page coinringtoolsllc.com/contact/ Thank you, Gary

[@lisacox9809]

Purchased this set and am having trouble with my coin 1964 pennies moving (not annealed). Using the CRT 17 degree .80 Die. Placed the doming tool lid with the 3 shims on top of the coin and Smallest Delrin push rod. Using a Harbor freight 6 ton press and going pretty slow, the penny keeps moving to the side of the die and not creating a dome. Tried an un-annealed quarter and the coin did not move made a decent dome. Perplexed as to why the penny keeps moving. Suggestions as to what I may be doing wrong much appreciated. I wanted to make some cool penny buttons.

[@legacybrandcoinringtools2956]

Jack Five. You might try the middle size pin for initial fold, then move to the smallest pin if that's the one you would like to use. You might also try a thin piece of leather or equivalent material on top of the coin prior to press. Also you want to use the least amount of shims to bring the lid closer to the top of the coin, however high enough to hold the pin square.

[@lisacox9809]

@@legacybrandcoinringtools2956 Thanks so much for the tips. The middle doming tool was the key. I bought these tools due to your awesome videos and explanation.

[@legacybrandcoinringtools2956]

Happy to help. Here at Legacy you get that kind of support. Happy ringing.. Gary

[@WickBeavers]

what size do I need to do silver dollars?

[@legacybrandcoinringtools2956]

Wick, not sure what size item you are asking about? Die, punch, pin? Give me a call 870-421-3029

[@SabirAli-tc4kt]

I need all these tools. How i can get ??

[@legacybrandcoinringtools2956]

These tools can be purchased on the Legacy site online. Here is a link to the online store www.etsy.com/shop/CoinRingTools please let us know if you have any questions, thank you.

[@robertkirchner7523]

po@@legacybrandcoinringtools2956