Complete Toyota 3.4 Swap Tutorial: Everything You Need to Know

Join us in this exciting engine swap project as we replace the old, unreliable 3.0 3VZ with a powerful and ultra-reliable 3.4 5VZ. In this video, we cover everything you need to know to swap out the motor on a Toyota 4Runner or Pickup, including all the wiring and additional components required for the upgrade. Follow along as we take you through the entire process, from start to finish, and show you how to make your rig more powerful, reliable, and ready for off-road adventure!
Crossover Pipe Flip: www.yotatech.com/forums/f160/...
Support Dirt Garage by purchasing our Merch! - www.dirtgarage.ca
Brought to you by @ Alpine Toyota - alpinetoyota.com
INSTAGRAM - / dirt_garage
Get 10% OFF Afraid Knot Ropes with my discount code "dirtgarage"
www.afraidknotropes.ca/
My 2020 OFFROAD Gear Kit / Recommendations: USA Affiliate Links
Lunchbox Locker: amzn.to/34lDTfI
Smittybilt Compressor: amzn.to/2vhwEqm
Tire Deflator Tool: amzn.to/2SwmbPO
Smittybilt Winch: amzn.to/2HbKP2Y
Recovery Rope: amzn.to/39om3Ze
Soft Shackle: amzn.to/3bnRg0t
Hard Shackle: amzn.to/39ouyDA
Recovery Hitch: hamzn.to/2SeE6LN
CANADIAN Amazon Affiliate Links:
Smittybilt Compressor: amzn.to/35DcvY3
Tire Deflator Tool: amzn.to/2QBWPQA
Smittybilt Winch: amzn.to/35CBOJO
Recovery Rope: amzn.to/2s9qRlj
Soft Shackle: amzn.to/2R4j5Bx
Hard Shackle: amzn.to/39QXpl3
Recovery Hitch: amzn.to/306WyIL
Music Licensed @ Artlist
Find music for your videos on Artlist! artlist.io/Clinton-279876
My 1989 Toyota Pickup Build: • My DREAM Toyota Build!...
- 1UZ-FE V8 Swap
- Manual Swap
- Dual Transfer Cases 2.23 x 4.7
- Solid Axle Swap / SAS
- Lunchbox Rear, E-Locker Front
- OME Rear Springs & Tundra shackles
- Auxbeam Headlights: shrsl.com/38hjx
- 37x12.5r17 Toyo MT Tires
Camera Gear Used To Make This Video:
- Camera: amzn.to/36C4dkI
- Microphone: amzn.to/2QDkIaB
- Tripod: amzn.to/2sdCkR0
- Gimble: amzn.to/2FyndVf
Business contact: [e-mail]

[@matthieucorbeilwalsh]

Curently in the middle of a 3.4 swap in my '90 4runner. So glad you guys are documenting this swap more than before.

[@RedBeardToyota]

How’s the project going!? I’m also doing a 92 4Runner

[@matthieucorbeilwalsh]

@@RedBeardToyota Engine is in, found the right transmission and driveshaft combination since mine was automatic and I want this one to be a manual. Air intake and battery are moved. Crossover pipe and exhaust done. Now I'm finishing some non-swap related things while I wait for some parts. Then its wiring time.

[@melvynmartinez4038]

@@matthieucorbeilwalsh Greetings from Venezuela. I am doing this swap right now. My 4runner is a 1992 5 speed and the donor engine comes from a 2001 runner automatic. I am not a mechanic by profession, I just love cars and I am passionate about mechanics. At this time I already installed the motor and all the mechanical part, now I am going to start with the electrical part. But I'm needing the combination meter diagrams, I can't find them online and as you know here in Venezuela it's a bit difficult to find them. Some of you will have them by chance, I appreciate your help. I have seen this video like 10 times or more, and I need the diagrams to be able to put the cluster, rpm, speed, to work.

[@mycum8818]

@@matthieucorbeilwalsh glad to hear that man, I got a 90 pickup that I swapped, but instead I didn’t use the crossover headers because the common cylinder head overheat problem I had with the original 3.0 engine, the long tubes I ordered helped a lot with the performance

[@TimmyTheToolman]

Did you buy a premade harness or adapt your own via wiring diagrams?

[@AustinKamuela]

This video is going to be on loop when I dive into documenting the 3.4 swap in my 94 4runner! Thank you Dirt Garage 🤙🏽

[@Davest420]

I just had my 91 Toyota pick up shipped out from Colorado to New Hampshire. I was going to just replace the 3.0 but I’m definitely going for the 3.4 now. I’m gonna watch all your videos on it and hopefully get er done

[@90yotapickup24]

been watching this on repeat taking notes for my upcoming swap!

[@offconstantlyfabrication]

Doing a two 3.4 swaps one from a 3.0 to 3.4 and the other is a 3rz to 3.4 definitely a good watch before I dive into this thanks for the detailed video

[@bread2669]

Thank you. Hoping to swap mine by this summer

[@wieser88]

Cool video! can't wait to see driving!

[@roofinggriggs8323]

Dude where were you 4 months ago with this how to video man? I’ve been struggling so bad with mine! 😂 good content keep ‘em coming! 🤘

[@wesleylambert9272]

Great stuff. About to do a swap in CA.

[@rogvarley6971]

About to do this swap myself, appreciate your video. Now, let’s talk about that mullet, bro.

[@petermorton2869]

Good on yous replacing the old engine to drop in the FAMOUS TOYOTA 3.4V6 5VZFE ENGINE & they are a Brilliant Engine & I have a 1996 Toyota Hilux Surf 3.4V6 5VZFE Engine & it has done 265,000 Kilometers & my son Regan brought the 1996 Toyota Hilux Surf 3.4V6 5VZFE Engine when it had done 117,000 Kilometers & when it had done around a 119,000 Kilometers I replaced the Spark Plugs with the HGK Iridium Spark Plugs & it's the best that I could have done & & when my son Regan Sold to me when it had done roughly around 125,000 Kilometers & I had kept up with the service & do the oil & filter changers & when it had got around 140,000 Kilometers & decided to check the NGK Iridium Spark Plugs & when I got the Spark Plugs out I wiped them with a clean rag & they looked really good these NGK Iridium Spark Plugs & I just screwed them back & just nipped them up tight & I never ever torque these down & you don't need to tighten tighten these plugs too tight as I just nip up tight & when the Toyota Hilux Surf 3.4V6 5VZFE Engine had done roughly around 185,000 Kilometers I took the HGK Iridium Spark Plugs out & check them again I just gave the a wipe with a clean rag & they looked fine & this time I put some PBC Copper Coat Grease on the threads of the Spark Plugs & at roughly the same time I did the Timing Cambelt, water pump,Tensioner & Idler pulley & I had to buy a new crankshaft pulley as the other was rust around the crankshaft itself & even though I was using a puller it actually broke the crankshaft pulley & I a terrible way way of getting the pulley off & in the end I had to use heat getting the pulley off & finally I got it off & I sanded the entire end of the crankshaft & with fine wet & dry sandpaper & came up really good & I priced a New crankshaft pulley at the Mount Shop in New Zealand as I live in New Zealand & the Mount Shop wanted $850.00 plus 15% GST stands for Goods Service Tax & I wasn't going to pay for that amount of money & that was way too expensive & I got a new one from Australia site for $336.00 & the first one didn't arrive & Aimee my Daughter-in law got back to him to say we never received it & he said he did send it & I told him we haven't received at all & I don't what happened to it & he sent another one & later down the track I had received it & got in touch with the guy to say we had received it & I don't know what happened to the first one he sent to me & never ever showed up otherwise I would have sent it back to him Bugger & must have gone missing in the post well anyway before I had put the new crankshaft pulley back on I put PBC Antiseize Copper Coat Grease onto the crankshaft & some on to the crankshaft pulley slid on easily tightened the crankshaft with a impact gun & put everything back together & sweet as & I noticed when I took the old cambelt off the timing was one tooth out & having the New cambelt on it spot on the dot & running really & I will be doing the cambelt change & water pump tensioner Ideller pulley & I will do the Camshafts seals & crankshaft seal & replaced the crankshaft seal last time around to when it is due & short time later on in a couple of weeks or so I will checkout the HGK IRIDIUM SPARK PLUGS & if they still look & will just wipe them with a clean rag & put them back in & just nip them back in & if they need to be replaced I will replace the Spark Plugs but at the moment the engine is running Sweet & no sign the 3.4V6 engine has a miss fire at all & you Sir will over the moon now that you have a Toyota 3.4V6 5VZFE ENGINEin your vehicle & if I had the money I & built this 3.4V6 5vzfe Engine up & so it would reboot 30 over sized & put 6 to 7 to one Venolia forged pistons steel crankshaft & Excellent Quality after market conrods & good camshafts to go with a Supercharger that got on these 3.4V6 engines & have a slightly smaller drive pulley to go on the Supercharger & able to pull more boost pressure & run lake pipes under the side skirts & have 2 oxygen sensors both sides of the exhaust system & I dont know if can get slightly bigger headers made up to fit the 3.4 V6 engines as that would even make a better improve ment & there is a Lovely Beautiful Blonde Lady on Utube & her Tacoma only has one Turbo on the 3.4V6 Engine & it pulling 11.11 seconds 1/4 mile & speed 121 miles per hour down the 1/4 mile & could be 122 mph pretty impressive in the USA at the drags & I wish you Sir all the best with your 3.4 V6 5VZFE ENGINE & have great fun with it Kind Regards Peter

[@billymunroe-williamson8840]

Watching this now I will also be watching this video and rewinding it several times in the future when it comes to wiring

[@Springer_maniac]

I’ve done everything on my 1990 4runner, rebuilt gas tank, fuel pump etc, plugs, wires and she’s overheating, tore the front off the engine replaced water pump and thermostat, no difference still overheating. This vehicle is so solid no rust great interior, no way I am scrapping it, there is a fresh rebuilt transmission and clutch. I found a donor vehicle with 180,000 miles is complete, if I park them side by side it should be easier than this vid because all the needed parts are there, hopefully can just switch it all over. I have a mechanic who will help me your vid is a great heads up to what is in store so thanks for that, hope I finally windup with an awesome 4Runner🤞

[@CopeManMTNDEW]

Awesome video. I got a couple 3.4s laying in my garage. My daily 89 pickup is wanting a 3.4. This video helped break it down for me.

[@duddleypiercejr.]

U got the 89 long bed?

[@dirkfrazier9779]

​​​​​@@duddleypiercejr. I do! 84! Long bed, and sorry, No it is not for sale. But, out of curiosity, every thing has a price! I have a 1984 Toyota long bed, 85k or less miles, on a 2.4 carbureted motor. I bought brand new in October of 83' and unfortunately, even with Rust Proofing, it's first 4 years in Wisconsin's (Salted not Plowed) Winters quickly took its toll. It has rust, nothing that can't be fixed and I do have front end damage on front passenger side that a hood, fender bumper, grill, headlight assembly, I have blinker and headlight, body work to align what bolts the body pieces bolt to down to the frame which is straight, won't fix and after that will need a paint job to have a primo completely stock truck. All original with bed cap included, less than 85,000 miles (I have to look) it's like 84k or something. Inside is clean with buckets, wing windows, slider rear window, cap too, tachometer, SR5, 5 speed manual, 95% on tread of tires, oh, has a cracked windshield that worked fine (still does) the State I moved to (WA) said I would have to replace to transfer registration which they wanted me to pay sales tax on since I was out of State even though I bought it in this State! (Go figure). I drove her here for over 2 years before being cited for expired tags and so I didn't have the cash to do the body work or pay the coffers here for their precious money they felt I owed them. I parked it having another rig, I didn't pursue the injustice, however, I did drive it for a number of years every Winter after a good snow fall because it's 4×4 and they don't have plows here just like the police won't venture out in inclement weather unless they are called and have to. They are sworn to serve, but that might require getting their hands dirty having to push someone to get them moving (the same in every state!). So, I have no intention on selling it, but money talks and some amount might persuade me, if your offer doesn't swing me then maybe someone out there has an offer that will. this comment will be here forever so someone might make an offer that does swing me before I get started on my project after I take care of a couple of wrinkles before I start on my project. Also, I quit driving it when the voltage regulator went out and someone stole the new one between moves, so it will need one of those too. Happy Hunting! 0:04 0:04 0:04

[@dirkfrazier9779]

​​@@duddleypiercejr. I

[@riseauto9551]

Awesome video I’m currently piecing my 5vz swap aswell 97 4runner ecu, one oxygen sensor, 2002 tacoma engine (non egr same as 4runner) 99 and up MAF, ORS harness, truck will only have a heater and radio under the dash, cool video lol took some notes 🤙🏼

[@estevanurrutia2007]

Killed it brotha good job 💪🏼💪🏼💪🏼👑👑👑👑👑👑👑👑👑🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥

[@fg9650]

That’s awesome bro! Thanks for the content.

[@daleferguson1233]

😮😮😮 bro. Your Awesome... I enjoy your show.

[@doughboy1966]

Awesome video.

[@sla052609]

Your wiring ability is impressive im still trying to find diagrams for obs style gmc/Chevy to finish my swap

[@NW-Woodsman]

Awesome vid. Do you have a link to the full engine control schematic to print out at home like you did?

[@rickysorell8532]

I’ll be doing the swap to a 86 Toyota pickup!

[@ericpaluch1462]

Is Thrice not touring right now? Lol kidding man - but you do look like Dustin Kensrue. Love the video!

[@LouisianaMechanic]

Another awesome video man. How often do you get people asking about thay front axle housing? Lol

[@DirtGarage]

Happens somewhat often haha

[@KingKong-bo7nk]

Cool makes me want to do one for fun

[@emmanuelmata]

This is an awesome video thank you for the time you took to make it simple and easy. Do you have a detailed video like this for the 1uz you just did? Thanks again brotha subscribed

[@DirtGarage]

1UZ was done a few years back, and there is a bunch of videos around it. Nothing as all in one as this though.

[@emmanuelmata]

@@DirtGarage got it thanks

[@macdoud5385]

Very informative vid guys, i recently bought a really nice stock 95' 4runner with a 3.0 with 168k miles. it runs good but i will be wanting to throw a 3.4 in it at some point. I was just wondering how you got to be so comfortable and knowledgeable when it comes to the wiring portion of swaps? Is it just from diving in and figuring it out or have you had schooling? I've rebuilt engines but when it comes to wiring i feel like an idiot haha. Also looking at a diagram is like trying to read chinese to me. I actully learned from your video that the diagrams continue to the next page, i had no clue!

[@nemesis851_]

11:20 I've never seen an engine get so excited about being brought to life

[@thottieboo7152]

I gotta make it out to BC. I drive a Ln130 that I 3.4 swapped from the 2lte. I would love to meet you! Hit some trails with ya

[@tylerhaunga3241]

Can you make a video of putting back vacume lines

[@ricardoares3546]

@DIRTGARAGE If you collaborate in a video of 3.4 (5VZ) swap on a Suzuki Samurai it will be a hell of a video:)

[@monette44]

I'm sorry... I was anticipating.... FIRE!!! 🤣

[@DirtGarage]

In the over a dozen engine swaps I've done.. Its happened once.

[@monette44]

@@DirtGarage So... What your saying is there's chance on the next one?! 🤭

[@DirtGarage]

@@monette44 No chance. You learn your lesson once. You have no idea what my fire anxiety is like these days

[@tylerhaunga3241]

Can you do a vacuum line video

[@leonelperez4635]

Nice were you got the engine diagram? I'm swap my 4runner 1995 3.0 to 3.4 but I need the engine control module diagram?

[@tysonrojas5477]

I've done my 3.4 swap but had issues with wiring a 2001 autobtrans 2wd since the older one use the kick down cable shifts hard a f and couldn5 find wiring harness worth a shit for anything

[@Cmc-365]

If I wanted to swap a jdm motor what do I have to change over to make it work?

[@liou8493]

can you do this with a bundera?

[@downto2538]

Can you make a comparison video between a v8 swap(1/2uz) and the 3.4 swap. Obviously the v8 has more power but how do they differ in terms of difficulty and what are the pros and cons of each outside of power output.

[@willtaylor4084]

Absolutely!

[@metrosoap1236]

would this be a good idea for my 99 2.7. mine is knocking

[@dylanknutson-wp4kh]

Could you link where you got the wiring diagram. Thanks

[@rattles3044]

Get a new cherry picker..... Use old (lightweight) to make a light rack. With a couple of old batteries (for power and recharging) placed on back of cherry picker (for counter weight). A new slide in bar for lights (12 volt LEDs). Should be plenty of light for work and filming. Depending on how you make your extendable light bar, it could be adjusted to fit just under hoods and be far enough to not interfere while working on engine. And to come in from both sides of vehicle . Just a thought!

[@4xhoser]

That is a genius idea 🤘🇨🇦

[@SOLDADITO76]

Just needs some AT-205 added to the engine hoist and it will be mint, any jack for that matter.

[@DirtGarage]

My cherry picker is fine. And my shop is waaay to small to rig up a cherry picker specifically for lighting.

[@paultthompson]

“Fuel coupler” is just future planning for a pressure gauge

[@DirtGarage]

True 🤣

[@rpiii3755]

I have an 89 pickup will this swap work with an automatic transmission?

[@JoseAguilar-lh5bq]

Hi I did the 3.4 swap en the engine is on the 4runner what i did it do is the wire harness i need Help Please let me know if you can help me I know it's not gonna be free just let me know please thank you

[@jakeolsen2764]

Swapping out the 3.0 on my 91 with a 2000 runner engine. Where did you get your wiring diagram. I have all the stuff.

[@tylerhaunga3241]

What runs in to the relays

[@nemesis851_]

For some reason YT, is only now (2 days after published) letting me know about it. Watching it now

[@nickt9467]

Yo! What kind of front bumper is that?

[@tylerhaunga3241]

So that red and white wire goes to the relays

[@rudyperez7628]

About to tackle this same swap into my 93 4 runner, but I have IFS. Do I still need to swap out the oil pickup tube and swap the oil pan from my 3.0 engine or can I just leave the 3.4 oil pickup tube and pan since I don't have SAS? Awesome detailed video!

[@DirtGarage]

Even more important on the IFS. That pan is shaped specifically to clear 3.0 IFS. 3.4 pan will no clear front suspension.

[@rudyperez7628]

@@DirtGarage Just wanted to say that your video was extremely helpful in doing my first 3.4 into 2d gen swap!

[@flj232]

How can one add AC to a 1988 Toyota pickup with 3.4 swap?

[@clydeowino6296]

Hey, Currently working on a 3.0 to 3.4 swap… is there any harm with using the baffle from the 3.0? On the right side where the ac compressor mount interfaces with the engine mount, there’s a gap.Did you use a shim to compensate for the gap? 3.0 mount seems to be thicker than 3.4 where it bolts to the block.

[@rudyperez7628]

Just did the swap myself and didn't run into this issue? Curious to see what you're talking about tho

[@beachthor1]

How do people learn this stuff? I mean other than a professional education. How do you know you did everything and connected everything after it’s done? I am deep in a rabbit hole on engine swaps, so amazing to watch and see what people can do to make their cars better.

[@DirtGarage]

I have no education. Just lots of trial and error. Google is your friend to learn the basics.

[@melvynmartinez4038]

@@DirtGarage Greetings from Venezuela. I am doing this swap right now. My 4runner is a 1992 5 speed and the donor engine comes from a 2001 runner automatic. I am not a mechanic by profession, I just love cars and I am passionate about mechanics. At this time I already installed the motor and all the mechanical part, now I am going to start with the electrical part. But I'm needing the combination meter diagrams, I can't find them online and as you know here in Venezuela it's a bit difficult to find them. Some of you will have them by chance, I appreciate your help. I have seen this video like 10 times or more, and I need the diagrams to be able to put the cluster, rpm, speed, to work.

[@bertbccfu9564]

Yep trial and error, 30 years ago when I started doing this stuff there of course was no internet no youtube, , youtube is a giant help when doing this stuff , it seems whatever you can think up for a swap somewhere someone has already done it ,

[@jesselewis8624]

Where do you get your wiring diagrams? I need one for a 97 T100 and a 94 Pickup both 4x4 manual trans.

[@DirtGarage]

Dealerships

[@Davest420]

I have a 91 pick up. Can this be done with the stock suspension or should I lift it and put a solid front in before the swap?

[@DirtGarage]

No lift or solid axle required. Process is the same either way.

[@shadekure7858]

How's swapping the 3.4 into a 4runner from a 22re? Will it fit on the trans ?

[@DirtGarage]

Nope. Need the v6 trans. But the trans and crossmember from v6 will bolt in

[@hawaiianslamma]

So what happens with the two plugs that u have from the 3.0 with the wires cut?

[@DirtGarage]

Those are the body plugs.

[@kennethbigham9920]

Stupid question but can you use an auto ecu in a manual. I have a 93 3blow and got a 5vzfe and can only find auto ecu's. If it posible?? 😅

[@DirtGarage]

Yup. This one we used a auto ecu. Most 3.4 swaps I've done we used auto ecus

[@davidlewis180]

Do you have a link to where you got the diagrams from ?

[@DirtGarage]

Toyota dealerships

[@Rproductionz1]

If I were to do this on my 22re will the engine mounts bolt up ?

[@DirtGarage]

Nope. We have a video doing this to a 85 pickup with a 22RE. We had to make the mounts

[@rileymorrill4135]

If my 4 runner has a sas I wouldn’t have to worry about the oil pan correct?

[@DirtGarage]

You have to worry about the pan.. This is a SAS truck. No matter what the pan needs to be swapped.

[@Mister006]

everything is on the other side! The airbox, fuse box and battery swap sides.

[@DirtGarage]

Just battery and Intake swap sides.

[@tylerhaunga3241]

Can I get a link for a diagram

[@fortnite_king_of_drift]

I am from the Dominican Republic I would like to know which mechanical transmission fits the 5vz help please??🙏🙏

[@DirtGarage]

R150

[@fortnite_king_of_drift]

@@DirtGarage Thank you brother from the heart 🙏

[@ndspeedster]

I don't know if you mentioned this in the video earlier I might have missed it but you need to put a body lift on your truck after you do the swap otherwise the engine will hit the hood because it's taller than the 3.0. That means you have to use different cooling hoses too for the radiator because they need to be a little longer

[@DirtGarage]

Nope! Didn't mention it because it wasn't required. In some cases you have to cut a bit of hood bracing out, but 3.4s fit nicely in others without cutting.

[@leogonzalez7109]

I have a 91 4runner with a 3.4, I got it with the TRD supercharger and I am having fitment issues with the hood. I have looked online regarding a 2nd gen hood swap and haven’t gotten anything secure to go with.

[@rudyperez7628]

Cut out the underside skeleton of the hood yet?

[@justynpeck9510]

Hey man if your in Oregon I would love the help on doing my wife’s 3.4 swap in her Toyota pickup I’m not good with wiring at all so ya if you could I’m in Portland area

[@DirtGarage]

I am not in Oregon

[@rudyperez7628]

If you not confident with the wiring, couple of companies make and sell harness. I believe one is in Creswell, Oregon.

[@devilvenom]

What is the transmission that you used on the car?

[@DirtGarage]

Stock. R150

[@SixFo-wk3hg]

Which motor mounts did you use 3.4 or 3.0?

[@palefacepointpreserverwasi3391]

He used the 3.0

[@nemesis851_]

Wish I had some kind of shelter to work on my vehicle. The back open driveway, to a public alley, is so sketchy, and not really a workable space.

[@kristenhenry3342]

I have the same engine (1994 Toyota pickup V6 3.0/3VZE), and I'm getting a code 24 and code 31...rough idle, rich running, hesitation sometimes when i press on the gas pedal, check engine light on, and occasional backfire when first starting (cold). The truck came with an EGR delete set up, as well as a cold air intake simplification mod when I bought it. If you (or anyone) could offer some guidance, I am by myself and really need help. Thanks!

[@nyg974ever29]

Hey brother I’m in the same exact situation. What did you end up doing?

[@drewpope1964]

Hey man I’m doing This swap to, I bought a 2000 model 4Runner with the 3.4 and automatic transmission. I’m putting it into my 1989 4Runner but it’s a manual will the computer still work even though there 2 different transmissions?

[@DirtGarage]

Probably not. Not because it's a automatic, but because it's a 2000 model, I always try and tell people to stay away from 99+ because they commonly have immobilizers. If your lucky it won't, usually base model trucks won't, but limiteds have generally all have immobilizers, but also some SR5s 😅. Either way if it doesn't have one your set, the motor, harness and ecu we used in this was from a auto and we attached it to a manual.

[@drewpope1964]

Ok cool thanks man! That was a great video!

[@dafuq2165]

Can't you delete the crossover pipe due to it causing burnt valves and head gasket problems

[@DirtGarage]

Nah, that's not a issue on these.

[@miguelitomartinez9178]

Does it work with the 3.0 transmission?

[@rudyperez7628]

Yes

[@alexissantiago9415]

Why you have to change the oil dip stick ?

[@DirtGarage]

To match new sump location on pan

[@ronaldpotter3962]

watching cherry picker slowly bleed off LOL

[@ernestogarcia8014]

Did you have ABS and if you did, did you delete it?

[@DirtGarage]

We generally delete abs from everything

[@tommcl8548]

👍👊

[@4xhoser]

Justin Braun is on the rev limiter like mad in a 3.4 supercharged 🤘🇨🇦

[@xurritoalejandro8109]

Is the 3.4 better than the 22re in terms of reliability and durability?

[@DirtGarage]

Yes, these motors go forever. I've seen alot more killed 22res than I have 3.4s

[@xurritoalejandro8109]

@@DirtGarage thanks. Do you know how much it costs to do the swap? Just labor?

[@SOLDADITO76]

Put some AT-205 in that engine hoist and it will stop bleeding down. The 3.0 must go, like you said the 3.4l is so much better. No comparison to the 4cyl which is what I originally had. You don't have to cut the fuel line if you are not in a hurry. On a 4cyl truck there is a threaded coupler you can use to connect the two. That couple is located near the fuel tank or towards the engine along the hard line. From 4cyl to 3.4l you want the fuel line from 3.0engine flip it 90* and couple that to the fuel line on the pass side. As with Toyota brake lines the thread pitch is the same, longer brake lines needed just add a stock brake line, and that is the same with fuel line hoses. I did this same swap just not to long ago into my 84-04 SR5/TRD pickup, and yes that's is all the years/generations of Toyota's my rig is built with. When I did the 3.4l swap I took it one step further by rewiring the complete truck from fuse box harness, battery harness, dash harness, fuel pump, all the way back to the tails lights. Moved the battery to left hand side and also installed a complete dash and HVAC system out of a first gen Tacoma. The 04 e-locker works as Toyota intended with the stock switch and the speedometer is driven by my 84 RF1A transfer case. Everything under the hood is out of the a first gen Tacoma and in the same location as well, right down to the opening in the firewall for the engine harness. You would never tell that my rig didn't come like this from the factory. Next engine swap may just in fact be the V8, that job will get a 3.4l to 4.7l adapter harness when I locate one.

[@DirtGarage]

It was full. Just wasn't tightened. It was moving so slow we didn't notice, but you can definitely tell in time-lapse

[@SOLDADITO76]

At-205 will help the seals reseal and it won't leak down.

[@SOLDADITO76]

Also the link for the crossover forum is missing in the description I've noticed.

[@bertbccfu9564]

I'm debating a v8 swap also , but this is in my 1st gen Tacoma, going with the 1uz though for the weight savings

[@user-yg4yk4cc9g]

One wheelhihair size maters shake a hand ✋️

[@user-ry2lt8ki5b]

Смотрю тебя братишка ❤

[@FK-we1dp]

where did you get your motor?

[@DirtGarage]

I believe this one came from Facebook marketplace.

[@eliasalvarado6656]

Where do ya get the prints you have????

[@DirtGarage]

Toyota dealership

[@eliasalvarado6656]

do i just go and ask for them or do they charge??? @@DirtGarage

[@matthewsimmons7795]

Where you get the diagram for the 3.4 l

[@DirtGarage]

Toyota Dealership.

[@matthewsimmons7795]

@@DirtGarage ok

[@matthewwheeler6178]

So the stock 3.0 manual transmission blows right up to the 3.4

[@DirtGarage]

Yes. The manual 3.0 trans bolts to 3.4

[@mckennacooper6170]

@@DirtGarageis there supposed to be a dust cover on the bottom half of the fly wheel? Currently half way through a SAS.. 3.4 engine, putting in the 3.0 transmission but the bottom of the fly wheel is exposed. Doesn’t seem right to me..

[@DirtGarage]

@@mckennacooper6170 Yeah, use the 3.0 cover.

[@donmarro7663]

Hi, can you share the diagrams?

[@DirtGarage]

You get them fon dealership or TIS

[@CB-hr6zs]

Come to Hawaii and swap my 3.0 for a 3.4

[@morgannordahl4355]

I'm no mechanic but pretty sure you aren't supposed to use the green coolant in toyota trucks. Maybe that contributed to the blown head gasket.

[@DirtGarage]

the 3.0 contributed to bad head gasket. I run red in everything, but this engine just had the coolant the 4Runner came with still in the system.

[@bertbccfu9564]

You can run green but you cannot mix them it makes mud,

[@JoseAguilar-lh5bq]

The question is Possible to do it and automatic transmission

[@CCinthesaddle]

3.0 doesn't get hot with a 6 quart oil pan.

[@Gee_Dub]

10% for 5:44

[@DirtGarage]

10% for bellhousing bolts?

[@JoseAguilar-lh5bq]

Sr I have question l have 1995 4runner and I tried to do the swap but my trasmision is automatic and I have trouble with the wire harness harness

[@DirtGarage]

You need to use the automatic from the 3.4! Then to get the transfercase to drop on correct side you need an adapter to go from 3.4 auto to gear drive case from earlier Toyota 4 cyl.

[@JoseAguilar-lh5bq]

Sorry I didn't I don't know a lot So all I got is the transmission from 3.0 is not going to work ?

[@DirtGarage]

@JoseAguilar-lh5bq No, the 3.0 transmission will bolt up, but will not function, the 3.4 computer can not talk to it.

[@JoseAguilar-lh5bq]

Ok thanks for your help

[@JoseAguilar-lh5bq]

Hi I need advise with this problem I have with the transmission I don't know what to Get of automatic transmission on manual for the 3.4 swap what is the best solution

[@sebastiencolon2944]

The world needs the first 22r to 5vzfe DETAILED swap. IT DOESNT EXIST!

[@DirtGarage]

It's essentially the same. We have a video on that too. Still mostly bolt on with right trans. But gotta make engine mounts.

[@sebastiencolon2944]

yes but the wiring and fuel systems is for sure different@@DirtGarage

[@DirtGarage]

@@sebastiencolon2944 Not much different. You'd need a fuel pump and just do a basic harness for it with switched power.

[@sebastiencolon2944]

I got a harness built and now in the stage of having to splice into the body harness and don't know where to start without pulling the whole dash and tracing wire by wire@@DirtGarage

[@DirtGarage]

@@sebastiencolon2944 Pretty much what you have to do. Older trucks hard to find a reliable diagram.

[@jamesvang3456]

Next time just drill the dip stick hole instead of knocking it out works the same

[@DirtGarage]

It can be easy to knock it out.

[@RedBeardToyota]

@@DirtGarage exactly why would you spend time drilling if you can just knock it out 😂

[@DirtGarage]

@@RedBeardToyota Because it broke in half in this video.

[@RedBeardToyota]

@@DirtGarage I remember both of my motors had a plug that I used a punch to knock out and replaced with my 3.0 plug and just replaced it , I know some motors you have to drill them out right ?

[@DirtGarage]

@RedBeard Off-roading Yup. 99+ motors require drilling. We just got unlucky and the shaft attached to plug broke off in block.

[@abandonbelief]

11:34 YOUR CHERRY PICKER HYDRAULICS HAVE A SMALL LEAK OR AIR IN THE LINE OR SOMETHING... TIME LAPSE TELLS IT ALL. STAY SAFE.

[@DirtGarage]

The valve was just not closed all the way 🤣 It's fine. You can see in later time-lapse the issue is resolved.

[@nemesis851_]

Throttle response sounds like it take 3 ms, better than my 5 whole seconds on my truck

[@jcpage305]

I was looking into the 3.4 swap on my 92 4runner. After watching this video.... I decided not to.

[@rudyperez7628]

Why not? It's actually pretty simple and straight forward.

[@3ormorecharacterstimes2]

Everybody I've talked to that have done this swap says to use flywheel and clutch from the 3.4 only the bearing from a 3.0

[@DirtGarage]

You can if you want! But all 3.0 stuff also works.

[@3ormorecharacterstimes2]

@@DirtGarage guess I'll take a comparison when I get the 3.0 out

[@duddleypiercejr.]

Own fuse box as in fuse box from a 3.4. & get rid of tye original 3.0. engine fuse box?

[@DirtGarage]

Nope

[@duddleypiercejr.]

@@DirtGarage original fuse box works well?

[@DirtGarage]

@@duddleypiercejr. No reason to touch either fuse box. Gotta leave the factory one for body harness.