I really enjoyed this video and found it helpful! Usually I like applying the laminate sheet over the entire piece of paper, then covering the registration lines with matte scotch tape. Even though it adds an extra step, it doesn’t require me to precisely cut and line up the laminate sheet inside of the lines, and the scraps that get cut off the edge aren’t good for much else anyway. The laminate sheet is also usually a little bit bigger than the 8.5 x 11 piece of paper, so the edges stick to the cutting mat and allow me to get more life out of an old less sticky mat. ☺️
@Lacroix999 Жыл бұрын
If you stick your sticker sheet on your Cricut mat, it helps hold it down so it’s not shift all over the place while you’re putting the laminate vinyl on.
@rebecarod1475 Жыл бұрын
What a difference a year makes. Bought my Maker last year and have watched dozens of your videos, including this one. I understand this so much better now that I’ve tried print then cut multiple times and stickers a few times. Thanks so much.
@AngieHolden Жыл бұрын
Great to hear!
@mimimim2 жыл бұрын
Thank you for explaining to add the protective sheets within the cutting lines, I have been trying forever to make stickers with no success. I finally was able to print stickers today! I will definitely purchase the sponsored product. You ROCK!!
@AngieHolden2 жыл бұрын
You can do it!
@M2345M Жыл бұрын
wow the level of detail! thank you so much, I just made my first stickers for my husband. I would love to print, stick the clear on top then cut all the way through with the clear offset.
@AngieHolden Жыл бұрын
Glad it was helpful!
@ZaidaBaadjies Жыл бұрын
Love your video.❤ Just a FYI, the Cricut Explore 3 has an improved sensor for print and cut. I was able to cut through laminated cards with my Explore 3. So no need to place the laminate within the registration marks😉
@AngieHolden Жыл бұрын
I do understand that however MANY people have issues with their cuts being off from this so I just recommend cutting it to be safe.
@questionswithconnie11 ай бұрын
Thank you for how clear and concise your explanations are! ❤
@AngieHolden11 ай бұрын
Glad it was helpful!
@OrionsCornerDesigns2 ай бұрын
Hello- great video! I do have a question if you have time. I’ve been using my new Cricuy Maker 2 and making stickers with thermal heat laminate. No matter how I cut the laminate starts to come up on the edges! I’m pulling my hair out. I will be trying the cold press but wondering if you have experienced the laminate pulling up? Thanks! Mary
@AngieHolden2 ай бұрын
Yes. A thermal heat laminate definitely peels up after you cut it! You might way to try a different product.
@savillah Жыл бұрын
Excellent video, Angie!!! You always come through.
@AngieHolden Жыл бұрын
Thank you so much!
@Lacroix999 Жыл бұрын
To bypass the sensor not being able to read the guidelines due to the glossiness, you can add a piece of matte tape over the lines. Having said that, cutting the vinyl down before cutting it on a Cricut, can also save unused material waste as well.
@Xpresxions Жыл бұрын
How ?
@kamiGTRАй бұрын
@@Xpresxions place the matt tape over the registration lines
@Dee_B232 жыл бұрын
Thank you for this tutorial Angie. I have been wanting to do Stickers and now inspired to do so. Love your videos. ❤😊
@AngieHolden2 жыл бұрын
Have fun!
@MsDeLo606 ай бұрын
Thank you I was looking for the second way.
@AngieHolden6 ай бұрын
Awesome!
@Wannabecrafting247 Жыл бұрын
Thank you! I loved the extra tips !
@AngieHolden Жыл бұрын
You're so welcome!
@martahoshell7934 Жыл бұрын
Awesome video! Thank you for sharing.🥰
@AngieHolden Жыл бұрын
Thanks for watching!
@onecraftycookie2 жыл бұрын
LOL its so funny I've been laminating my stickers for years and now I'm seeing it everywhere. I use cold laminate I love it. I don't sell mine I use them for my packages on stuff I sell. I use my laminating machine on cold and I never get bubbles....love it
@titajese2 жыл бұрын
Hi, do you just use self adhesive laminate for cold laminate?
@onecraftycookie2 жыл бұрын
@@titajese Yeah it's just a cold laminate self sticking sheet but I do put that on and then I put it through my laminator on cold so that it gets every bubble out.
@chicboutiquellc Жыл бұрын
Great videos!! What vinyl do you recommend printing stickers on and which laminate?
@AngieHolden Жыл бұрын
I link to everything I use in the description below the video.
@Leena79 Жыл бұрын
Thank you for a great video! I never thought of using the clear sticker as a laminate, and I've been searching everywhere online for actual laminate sheets to buy, only to find that in Europe, the best brands are sold in 50 meter rolls (which is a lot of laminate for a small sticker side business). I have a question though: Wouldn't it be easier, for the weather-proof sticker, to first cut the sticker sheet without the laminate, and add a box around the sticker area, leaving the registration box, then remove the surrounding sticker, add the clear laminate on the whole sheet, and then cut the whole thing again? Instead of adding the laminate on individual stickers? Anyways, I'm going to go order the clear stickers now, so I get to try this method. 💗
@AngieHolden Жыл бұрын
Maybe? You can try it!
@valerieh42808 ай бұрын
Thank you for this helpful video. My stickers will be 1000 times better now!
@AngieHolden8 ай бұрын
Glad it helped!
@Luxinda2 жыл бұрын
Love Online Labels!!! Very helpful video 🥰
@AngieHolden2 жыл бұрын
Me too!! Thanks for watching!
@angelaarey9332 жыл бұрын
Thank you for this video. Makes me want to try making stickers!!!
@AngieHolden2 жыл бұрын
I love making stickers with my machine!
@paulacombs58692 жыл бұрын
Now I would like to try this. Thank you for the tutorial.
@AngieHolden2 жыл бұрын
Hope you enjoy!
@TurkawskiFam Жыл бұрын
Could you put one on these on a Yeti or Stanley tumbler and seal it with something?
@AngieHolden Жыл бұрын
Generally people add this kind of sticker to a tumbler just as is. If you wanted to seal over it and make it permanent, I would look into Epoxy.
@jodyparkman74402 жыл бұрын
Angie!! I love your videos! They have helped me so much!
@ScottEmbry-n2g2 ай бұрын
How do you make a trough cut with the second method of adding the laminate after? Will the laminate be hanging over the edge of the sticker?
@AngieHolden2 ай бұрын
Yes it would hang over the sticker.
@CloudSproutStudio Жыл бұрын
Are stickers from an inkjet printer even waterproof at all since the ink is water soluble? Dont you have to laminate it if you want it to be waterproof? Thanks for the video!!
@AngieHolden Жыл бұрын
I am laminating them in this video. They do make "waterproof" sticker papers that I have had luck with.
@CloudSproutStudio Жыл бұрын
@@AngieHolden Thanks!
@moontesseractpro Жыл бұрын
HI Angie- I like the extra protection with laminate AFTER, but I need die cut stickers. How would i make for a customer?
@AngieHolden Жыл бұрын
You would need to cut through on both. Then keep the backing to the laminate. Apply the laminate then add the backing back to it.
@bethmea51932 жыл бұрын
This is very helpful thanks! Do you have a video of how to make magnets like this?
@AngieHolden2 жыл бұрын
Try this: kzbin.info/www/bejne/mXXdhoZ3nbCeY6M
@bethmea51932 жыл бұрын
Thanks Angie!
@bobslfcu7732 жыл бұрын
Nice video. If the stickers don't cut all the way thru, can you press the go button again before removing the mat? Could that cut the mat by doing that? Or if you pick a setting that is too heavy for the paper, will that cut the mat? Thanx for the info.
@AngieHolden2 жыл бұрын
You can press go again. But yes you can go too deep.
@jessluebke16652 ай бұрын
I have been doing the laminate stickers on water bottles (laminate first then cut) and I notice that you could still pick at them and they might come up. Would laminating after with the laminate a little bigger help with this?
@AngieHolden2 ай бұрын
It helps a little but ANY sticker will be able to be peeled up if you pick at it.
@sheryloconnell4293 Жыл бұрын
Angie, I recently purchased a thermal laminator and I will be using the 3ml matte pouches. Will my Maker3 be able to cut the sticker through this laminated print and cut sheet? If so, what setting should I use?
@AngieHolden Жыл бұрын
I am sure it will. You will probably have to do some test settings. Maybe start with glitter vinyl setting then move to heavy cardstock if that doesn't work.
@dottyearnhardt96002 жыл бұрын
Your videos are great! Thanks
@Stickerissimo2 ай бұрын
Hi. There is a way to cut the extra offset in a second step without keep off the sticker? Print, cut the first time, apply the laminate on the top of sticker, put on again the sticker on circuit and cut with offset... Is it possible? Thanks
@AngieHolden2 ай бұрын
No it is not really possible!
@MyNailsandMorebyJohna2 жыл бұрын
Another great teaching video loved it
@AngieHolden2 жыл бұрын
Glad you enjoyed it!
@MyNailsandMorebyJohna2 жыл бұрын
@@AngieHolden yes I did you are welcome honey
@sheilalittlejohnmyers18862 жыл бұрын
Hi Angie, thanks so very much for this video! Would this be the best option for adding a design to wood?
@AngieHolden2 жыл бұрын
Try this: kzbin.info/www/bejne/q5uxoIKgorasoNE
@simplyblessed_2 жыл бұрын
Can’t wait to try this
@AngieHolden2 жыл бұрын
Enjoy!
@colorbugoriginals44572 жыл бұрын
Hi, thanks so much. Do you have any tricks for embossing / debossing on adhesive vinyl? Thx 😊
@AngieHolden2 жыл бұрын
I do not!
@colorbugoriginals44572 жыл бұрын
@@AngieHolden appreciate the reply :) working on braille options for decals
@Itselisamolina Жыл бұрын
thank you for this! when I click on the link to buy the laminate sheet, it asks to choose the material. which one did you buy for this tutorial? the standard white?
@AngieHolden Жыл бұрын
Yes I used standard white matte.
@deedeenyx39279 ай бұрын
Thank you !
@AngieHolden9 ай бұрын
You're welcome!
@kissimmeedisney Жыл бұрын
I started making stickers with print and cut on my cricut yesterday. I went through all of my ink! I am making photo stickers on glossy photo paper. At $55 a pop for ink, I can't see this turning into a side business. I'm using a brand new Epson WF295 to print. Am I doing something wrong? Thanks
@AngieHolden Жыл бұрын
I don't use that much ink when printing mine. It depends on a lot of factors though.
@yakztirialopez Жыл бұрын
thank you...what printer you use and where can I by it!
@AngieHolden Жыл бұрын
Try this: kzbin.info/www/bejne/aX2WdaFrp9CEb6M
@conniesobczak21772 жыл бұрын
When u did the off set on the stickers did u put off set on each sticker or looks like u did the whole group, or was that just show and tell.
@AngieHolden2 жыл бұрын
This particular file was all grouped together when I imported it.
@123rororose Жыл бұрын
Im doing a water bottle which method would be great
@AngieHolden Жыл бұрын
I would definitely use a laminate sticker on a water bottle.
@Jaden_8562 жыл бұрын
Hello Angie love all your videos I need help I'm trying to put cricut design space in my galaxy tablet A I have the app on my laptop n have cricut access but when I go to play store the cricut app doesn't show up just cricut home do you have a video that shows how to do this ? Thank u
@AngieHolden2 жыл бұрын
I have had success getting it from the Google Play Store. Try searching for Cricut Design Space.
@Jaden_8562 жыл бұрын
Ok thank u very much 👍
@Rachy712 жыл бұрын
Is Laminate or transparent vinyl better for protection for stickers? I'm confused on the difference. My other question is there a way to make a full sheet of stickers on an 8x10
@AngieHolden2 жыл бұрын
It is similar. I prefer laminate. You can only do a maximum of 6.75x9.25 inches on a Cricut to have room for the box.
@jeffsgyrl112 жыл бұрын
Thanks Angie! Could I do this method to avoid epoxy or crystalac to design a cold cup or double wall acrylic?? I’m just getting into tumblers and have been doing a lot of research. I want to avoid epoxy for the toxicity and I don’t think I have the patience for all the layers of crystalac that are required. Is there any option that will work to seal decals/stickers or am I @$&%# out of luck??
@AngieHolden2 жыл бұрын
It won't be as waterproof as epoxy. Nothing really is!
@AshleeTuck2 жыл бұрын
My cricut maker 3 never lines up to make stickers correctly even with calibrating and I always end hand cutting them with the gyro cutter.
@SVGTuts2 жыл бұрын
Thanks so much for this! The laminate sheets will be a game-changer for some projects I'm working on that aren't actually stickers but need the laminate protection. 🙂I have your channel listed on my site as one to definitely watch!
@AngieHolden2 жыл бұрын
Yay! Happy to help!
@marisolalvarado83338 ай бұрын
Hello I’m I bit confused since I do not have a cricut could I still make stickers without the cricit and just using a laminator if so what paper could I use, I just want them for my small business to stick on my boxes. If anyone knows could you please answer my question thank you so much!
@hwlscentedcandlesandcraftsco Жыл бұрын
is it the clear gloss sticker the same with clear laminate? I could not find any store in canada selling online labels
@AngieHolden Жыл бұрын
I like the laminate over the top best. You can find other brands.
@evetteochoa2 жыл бұрын
I bought weatherproof vynil sticker paper for stickers and cold laminated them as well. My husband uses the stickers on his hard hat but they faded after a week. Could you help with that?
@AngieHolden2 жыл бұрын
If he is outside it is probably UV light. I would use a UV laminate.
@chauneceyomally Жыл бұрын
hi, will these adhere & survive hand washing on reusable hard plastic water bottles. (not the filled water bottles from grocery stores).
@AngieHolden Жыл бұрын
I would not recommend these for that.
@chauneceyomally Жыл бұрын
@@AngieHolden tku, for yr reply..
@christinefarnham6282 жыл бұрын
Does the sticker paper with extra laminate offset hold up well when applied to a vinyl surface?
@AngieHolden2 жыл бұрын
Not sure what you mean by vinyl surface? You may have to test it.
@CristinaRiveraBeauty2 жыл бұрын
So if I'm doing a die-cut/through cut (to sell) how do I have it so the laminate over the edge? Like if the customer wants to put it on a tumbler.
@AngieHolden2 жыл бұрын
That is more difficult. I would do a through cut on the laminate. Peel off laminate, add sticker, put laminate back on.
@Keyla26meh6 ай бұрын
I have a circuit joy xtra and it does do print then cut
@AngieHolden6 ай бұрын
This was filmed before the xtra was released.
@EmoNinjaKat897 ай бұрын
Do you happen to know of a trick to make car stickers? If its sublimation or printable vinyl, I made theses stickers but they faded from the sun on my car.
@AngieHolden7 ай бұрын
Try this: kzbin.info/www/bejne/a2qWg3Vud8plqZo
@VistaBayCrafts2 жыл бұрын
Thank You
@laaceymathis Жыл бұрын
The matte paper (recommended in the description) sticks to my cricut light grip mat. So much to that I had to rip it off the mat, ruining my stickers. Any suggestions?
@AngieHolden Жыл бұрын
I usually stick a new mat to my shirt a few times for more delicate materials.
@leeleelaroo2830 Жыл бұрын
Does it always print the box around the stickers? Thanks
@AngieHolden Жыл бұрын
The Cricut machine needs the box to locate the cuts.
@lisabrewer78252 жыл бұрын
How did you get such a large print then cut area. It looks bigger than the 6.75x9.25
@AngieHolden2 жыл бұрын
It is not any larger than that.
@lesliejumperreeves3066 Жыл бұрын
how did you get so many stickers out of your print then cut? I thought our limit was 6.75 x 9.2"
@AngieHolden Жыл бұрын
This is the maximum size. With the box, that max size is a full sheet of paper.
@beckyzayas57492 жыл бұрын
I just downloaded the cactus file from Creative Fabrica,. The images seem to have an offset already.I am new to Cricut.Can you help?
@AngieHolden2 жыл бұрын
Yep. I mention that in the video. They have a blank offset but I added a white one. That is my preference. Follow the step by step directions in the video to add one if you want one.
@MORTONRICK2 жыл бұрын
You can also change the color of the offset to white. Then you don't have to contour.
@andreagarofolo9431 Жыл бұрын
By any chance can I laminate printable sticker paper to be used for car decals
@AngieHolden Жыл бұрын
Try this: kzbin.info/www/bejne/a2qWg3Vud8plqZo
@jackieward662 жыл бұрын
Can you do a thru cut with the laminate added after? Just wondering how that would work if you were gifting the sticker to someone and they would need to backing on the whole sticker but the laminate wouldn’t have a backing - just the actual sticker? I hope that makes sense.
@AngieHolden2 жыл бұрын
I would probably do a through cut on the laminate. Apply to sticker. Then add backing to the entire thing.
@QueenRiviera5 ай бұрын
Use Acetate setting to cut all the way through.
@marinamaldonado59952 жыл бұрын
Can I use epoxy over matte sticker paper
@AngieHolden2 жыл бұрын
I would probably put a layer of decoupage or some sealer over it. Epoxy can attack paper as well as ink.
@mardellgrayhek99582 жыл бұрын
Why don't you use the sticker paper cut setting? Just curious.
@AngieHolden2 жыл бұрын
Sticker paper is actually for the Cricut sticker paper and it is really thick. I tried it and it went all the way through.
@iepreschool1331 Жыл бұрын
@@AngieHolden so would that setting maybe work if I wanted to do a through cut? I like to add stickers as freebies in my customers' packages, so I need to do the through cut for those.
@robira1313 Жыл бұрын
Applying the laminate over the individual stickers doesn't leave much room for error!
@AngieHolden Жыл бұрын
No it does not! Not my favorite way to do it!
@blessedmama43612 жыл бұрын
Where do you get that laminated paper???
@AngieHolden2 жыл бұрын
I have sources for everything I use in the description below the video. On computer, scroll down and click show more. On mobile, click the arrow to expand the description or swipe up on the video.
@hwlscentedcandlesandcraftsco Жыл бұрын
how much pressure when you cut the laminate
@AngieHolden Жыл бұрын
Depends on the laminate brand. I would say a light cardstock setting to cut all the way through the layers.
@Odolwa25 ай бұрын
Cricut's packaging is very confusing >.< Not only do they keep changing it, the labeling is very cryptic. I ended up getting white vinyl with holographic laminate. The only other package they had was one that said transparent, however, there are two kinds of transparent product. Transparent vinyl (no white background on the sticker) or, Transparent Laminate (white vinyl background with transparent laminate), they are both labeled exactly the same, but the SKU is different. Someone at cricut needs to be fired over this. The BIG issue is that the one that has transparent vinyl (no white background) actually shows white background sticker examples on the packaging, making one believe they are getting a white vinyl. Luckily I'm printing butterflies for someone and the holographic laminate is going to work out just fine in the end.
@okieqt18 ай бұрын
Laminating a sticker sheet is not making WATERPROOF stickers. That is making water resistant stickers. Huge difference. Laminated stickers should not be advertised as waterproof. Truly waterproof stickers can be run through the dishwasher, put on a truck or a kayak, etc.
@finchdrive5 ай бұрын
Okay then how to make waterproof?
@okieqt15 ай бұрын
@@finchdrive I get mine printed professionally.
@perpub4 ай бұрын
These methods are way too time consuming if you want make a lot of laminated stickers to sell. I have a faster simpler method. However, although I add a slit for peeling my stickers in the back, there is still the danger of the customer not seeing the slit and peeling the laminate off thinking that's how you're supposed to peel them. I'm looking for ways to make laminated stickers secure from having the laminate peeled off.
@Marthe-JerryHall-yq7zx Жыл бұрын
I only made it 35 seconds into this video because my misophonia was flaring up due to the stickiness of her mouth. Cute stickers and I’m sure it would have been informational but the irritation was mounting. Maybe swish water in your mouth before filming to reduce the sticky saliva.
@AngieHolden Жыл бұрын
Please feel free to not watch.
@Marthe-JerryHall-yq7zx Жыл бұрын
@@AngieHolden As I said, I did not. Found others.
@wendym.serrano34902 жыл бұрын
Every time I do print then cut I seem to get black smudges all over everything and I thought it was from the registration line around the outside but I think it might also come from any black that's on the print. I let my prints sit and sometimes for hours and I still have this problem. Do you think it's my paper or my printer? I have an Epson printer.
@AngieHolden2 жыл бұрын
My guess would be it is your sticker paper. Some brands do not dry. For reference, these sat MAYBE 5 minutes before cutting. Be sure to get inkjet paper if you have an inkjet and laser if you have a laser.