The Gt wont go any faster and i ive found a solution!
Пікірлер: 55
@devondaniels82594 жыл бұрын
Use the vaccuum pump to power the brake booster as well the brake will feel more consistent
@PeterAndersons4 жыл бұрын
Hey Matt, that thing shifts! A bit nicer than my stock barge. Great info with the tuning, cheers and take care Pete.
@MattBerrymotorsport4 жыл бұрын
Thanks Pete glad you enjoyed. I had a look on your channel the other day, mannnn you have a lot of subs haha well done
@PeterAndersons4 жыл бұрын
@@MattBerrymotorsport Mate, you should have a lot more than I do, your knowledge and explanation skills are second to none... It's a great channel which should be discovered sooner than later, cheers.
@MattBerrymotorsport4 жыл бұрын
Cheers I'll get there eventually, I work a full time job so it's hard to be able to post more often.
@PeterAndersons4 жыл бұрын
@@MattBerrymotorsport Actually there is one question I have for you... does a 5EFE from an Auto Paseo fit the 5sp amnual box from a Starlie? It's an early Paseo with the distributor, so plug and play from what I can see...
@MattBerrymotorsport4 жыл бұрын
Yeah Pete 5e and 4e manual or auto are all interchangeable
@Runaeh4 жыл бұрын
i have the g6r 6speed, its perfect for my needs, reving to 7200 and shifting right into power again. it is also same ratios from 1st to 2nd rest is longer, my car had the c150 stock :)
@Timroycampbell4 жыл бұрын
Can’t wait to see how much more power u get from the 6 speed box
@Theeclipseeee4 жыл бұрын
You can look here, this is the most powerful itb starlet of all that I have seen kzbin.info now this starlet sold :(
@Ricerguy4 жыл бұрын
Does that ecu do blended tuning or are you planning to only use the map sensor? Pro tip: the tps vs rpm(alpha-n) tuning will be better than a strsight map tune on ITBs, the issue is that there isn't enough volume in the"plenum "(space behind the throttle plates) so depending on rpm, your map sensor will read atmospheric pressure at only 2-10percent tps depending on the size of the throttles. I started using the" ITB mode on my ecu, its hell to get right but it will drive like a stock car. It uses itb load point graphs and blends the map for fueling under lower loads and tps for higher load accuracy. When you hook up the vacuum pump you should put a vacuum gauge to it, just incase. Too much vacuum is bad, you might need a bleed valve in place of the pcv and the other breather to the vacuum pump. I'm running one of those usdm MOROSO crank breather kits that use a venturi and check valve to the exhaust, I haven't had a chance to measure the vacuum (gauge broke) so I'm currently using it in place of the factory setup that would have used the intake to evacuate the fuel vapours and reroute them into the intake to be re-burned. My soliel a came with a c150-672 that had a 3.535 final drive, I swapped it for a different c150 that was mated to a 2E-L and it has a 4.312 final drive, its great, but now the car feels like it needs a 6th for cruising so the C60 or c160 is the end goal 😁
@MattBerrymotorsport4 жыл бұрын
The Microtech ecu has both modes, but you can only use one or the other. It doesn't work very well with TPS only but this next idea is my only hope. The vacuum pump isn't very big so hopefully it doesnt pull too much, I'll keep an eye on it 😁
@Ricerguy4 жыл бұрын
@@MattBerrymotorsport if the tps/alpha-n mode isn't very good on the setup I'd wager the ecu isn't very good for the setup. 😣 As much work as I put into my blended itb tune, I miss the sharp aggressiveness of the alpha - n tune, the only down side was it would cruise rich due to the fact that the cruise area is part of a transition for general acceleration, luckily it wasn't as bad because there's an option to enable a multiplication factor based on map to the table making it a hybrid alpha-n. Honestly if I didn't have such bad luck with my o2 sensor I'd go back to alpha-n
@andli4614 жыл бұрын
Having the dyno graph and knowing the gear ratios and FD it’s rather quick to plug the numbers in to excel (or even do some hand calcs) and get the output torque graph vs rpm in every gear. Based on that and also knowing the rpm drop in between gears, you can do some backwards calculations to determine the shift points for each gear (yes, it will very between them) to hit max output torque in the next gear. Bet you will find a small edge there. Works great for track racing. 👍
@MattBerrymotorsport4 жыл бұрын
Great idea mate I will check it out. 😊😊 It was really surprising at the drags last year, Mrs was driving, car was revving to 8K and ran a mid 17... Took 1000 rpm out of the rev limiter and it went over 1 second faster lol
@andli4614 жыл бұрын
Matt Berry NP. Glad if I can help. 👍
@wefwefwef.4 жыл бұрын
Just put a c160 in a uk spec ep91 with a mate, makes a world of difference so good
@westcoastpc4 жыл бұрын
Keep the videos coming Matt! Ive got a Corolla G6 6 speed box i want to fit to my ep82 at some point. I was hoping to use a lsd from a Toyota Mrs/mr2 roadster. Just not quiet sure if it will be a straight swap and fit the gt shafts. I had a g6 box in a td05 starlet about 13 years ago and it was great, it just needed an lsd though.
@MattBerrymotorsport4 жыл бұрын
When you say G6, should be a Toyota code? c150, c52, c56 ect
@westcoastpc4 жыл бұрын
@@MattBerrymotorsport i can't remember the code but its out of a Corolla g6 which came with a 4efe so they bolt right up to a 4efte. I can probably check the code tomorrow.
@MattBerrymotorsport4 жыл бұрын
All good man it will just give us both an answer to what exactly the box is 😊
@westcoastpc4 жыл бұрын
@@MattBerrymotorsport C161 is the code. Corolla EE111 EU spec C161 1st : 3,166 2nd :1,904 3rd : 1,233 4th : 0,969 5th : 0,815 6th : 0,628 Reverse : 3,250 Differential gear ratio : 4,529
@kyle_ep91674 жыл бұрын
beautiful car man, im running tt600 itbs on mine, cant beat the sound of them
@MattBerrymotorsport4 жыл бұрын
Thanks man! Very nice! How do they perform?
@kyle_ep91674 жыл бұрын
Matt Berry they are alright, i still need to play around with the map to make the most of them but i’ve just made it so its at least driveable. still some spots where it is lean or rich
@Theeclipseeee4 жыл бұрын
Hello, do you have some mods in you engine: 4efe pistons with 0.3 mm 5E head gasket? 1SZFE valve pushers? Valve springs from 2JZ?
@Oshane74744 жыл бұрын
Can u do a 7a-fe bottom end with a 20v blacktop head convertion 🙏🙏🙏🙏
@Timroycampbell4 жыл бұрын
How much power u make
@Oshane74744 жыл бұрын
I would like to do it
@MattBerrymotorsport4 жыл бұрын
If love to but not easy to find those parts and very expensive. Surely it's been done on KZbin before?
@Oshane74744 жыл бұрын
@@MattBerrymotorsport do have an idea how much horsepower it can make
@Timroycampbell4 жыл бұрын
Matt Berry what series’s microtech ecu you using and what’s best price for in need one ☝️ for my all motor 4efe and do they have a plug and play for Toyota 4e pin 26&16 just
@digby87874 жыл бұрын
know that road on the way back from bynoe any day!
@Timroycampbell4 жыл бұрын
C 163 gear box how much for that box if can’t buy one ☝️
@MattBerrymotorsport4 жыл бұрын
Ive never seen a c163?
@Timroycampbell4 жыл бұрын
Matt I make 102hp with my 4efe all motor in Jamaica 🇯🇲 thanks for all your help and videos
@White_Night_Demon2 жыл бұрын
so basically you need shorter gear ratios? Or lower gear ratios per gear?
@MattBerrymotorsport2 жыл бұрын
Shorter yes
@angelokarantonis75094 жыл бұрын
Have you ever brrrrrrrrppped it down the 1/4 mile and found out you had less torque at 50km/h ? Also did you get over 85km/h for top speed ? PS that ecu was just a pretend one wasn’t it ?
@White_Night_Demon2 жыл бұрын
lol that s2000 beating ur ass in the end! hahaha
@MattBerrymotorsport2 жыл бұрын
its also supercharged making almost 400 hp haha
@Yungltd4 жыл бұрын
How hard is it to do a head gasket on a starlet gt
@MattBerrymotorsport4 жыл бұрын
Pretty straight forward. I don't have a video on a gt but I did a video on my EP91 a few weeks ago
@yuhbwoyreactsc51374 жыл бұрын
You have a 5e itb setup bro I need one hmu
@HowToTurbo4 жыл бұрын
Race is on when you get the 6 speed boyo.
@MattBerrymotorsport4 жыл бұрын
Race is on when your turbo is on haha
@HowToTurbo4 жыл бұрын
@@MattBerrymotorsport I'm excited.
@diegodelgado64384 жыл бұрын
What ecu is that??
@MattBerrymotorsport4 жыл бұрын
Microtech ecu, made here in Australia 😊
@diegodelgado64384 жыл бұрын
Thanks for the reply
@slug97514 жыл бұрын
Nice...haha
@dougm04 жыл бұрын
You won’t know yourself with the 6 speed
@andrewrigg49054 жыл бұрын
Hey Matt check you Facebook Messages... I have PM you.
@MattBerrymotorsport4 жыл бұрын
Nothing has come through?
@White_Night_Demon2 жыл бұрын
@@MattBerrymotorsport hahahhahaa probably different account