CT SIZING CALCULATION| How to select CT ratio| CT parameters selection

Current Transformer or CT is an important component of Electrical power system. It is used for measurements of current and giving juice to the relays for protection. Current Transformer basically steps down the current so that it can be fed to any meter or relay.
current Transformer have some parameters like Class, ALF or accuracy limit factor, ISF or instrument safety factor etc. They have their own function to play.
Overall ration of CT determines how accurately the CT will work. Selection of lower Ratio causes over load, where as selection of higher CT ratio causes less sensitivity of the circuit.
#ElectricalTechnologyAndIndustrialPractice, #CT_Ratio, #CurrentTransformer
CT sizing calculation
CT ratio Calculation
CT ratio selection
Current Transformer sizing calculation
Current Transformer ratio Calculation
Current Transformer ratio selection
CT class selection
Current Transformer class selection
Current Transformer
Current Transformer in power system
what is accuracy limit factor
what is instrument safety factor
parameters selection of CT
parameters selection of current Transformer
Class of metering CT
class of metering current Transformer
Class of protection CT
class of protection Current Transformer
Class Selection of CT
Class Selection of current Transformer
Please like, share, comment and subscribe.
Thanks for watching the video

[@nik93393]

You have ability to threshold the remembering power of your students and stand them among the toppers grade!! Congratulations 🙏🙏

[@trilochan9152]

Great Video. You have skill of explaining in such a type that it will be forever in mind.

[@md.abdullatif6544]

Now I understand about ct ratio. Excellent

[@abhineshk.a609]

Dear sir thanks for your CT sizing calculation video. Your way of explanation is very simple and can understant easily. If possible please include the burden selection(VA) related to CT in your next video with the selection of wire resistance,size,relay burden details etc.

[@MegaPartyVan]

Your videos are amazing, I'm going to binge watch your whole channel.

[@hariharan4674]

Thanks sir, I got better clarity once again thanks

[@adnansworld744]

Min, Knee point voltage is essential for 5P10 or IDMT protection CTs as per standard. Any conversion table available for Knee point voltage to ALF or Vice versa. Any can answer please....

[@patakotisrinivas1918]

Good explanation sir...

[@sajisivan]

great vedio ...thanks a lot

[@Hemanth2787]

How the fault current will be dedect if the primary current is 100/1 ratio.. 100 ams is the max current knw

[@ashokkumarjangir5324]

Sir pls explain the line ct ratio when a bus bar connected to a two different transformer (AMT+TT) power will be 40MVA both and voltage 110kv/33kV for AMT and 110kV/27.5kV for TT. 🙏

[@jaydhokai8364]

Thanks for Video.

[@surendrakverma555]

Very good.

[@varimas]

Sir. Great explanation. May i please request a lecture video on lightning protection, its method, techniques and calculations. Thank you.

[@krishnam4844]

Sir great explanation. Plz give information about Types of CTs and PTs available in the market.

[@pritamchakrabarty3891]

Nicely explained... One doubt is there... Is PS class CT is same as protection class CT like 5P20?

[@himanshu2232]

Sir जब भी vedio लाते हो,धांसू ही लाते हो,और knowledge से भरपूर👍👍👍 प्लीज एक vedio PT के सिलेक्शन पर भी लाएं।

[@electricaltechnologyandind5335]

Sure....

[@manojkumarmahto9805]

Hello sir, really well explained in simple way. Please also make video on dual CT ratio selection

[@pratapjadhav]

Hii sir Which bases we considering on CT sizing and 20% margin spare ? Which Standard IS/IES We are studied?

[@TheMohlamonyane]

I have the same question. In other projects I worked they used 60% margin and I couldn't figure out why.

[@birdeyeview3901]

Great Video Bro👍

[@ktsmurthy21]

Sir, Good Explanation. That means In case of Fault , Metering CT will fail.

[@electricaltechnologyandind5335]

Will be short circuited to protect the meter

[@ktsmurthy21]

Can you Explain How It will Short Circuit.

[@elxanmusabayev1533]

Hello if 3200/5 CT with 5P20 class, means that 20x3200=64000x5%=3200A maximum error - is that correct?

[@electricaltechnologyandind5335]

Upto 20 times of rated current the error shall be with in 5%. Yes if 64000 A flows error can be upto 3200A.

[@balasubramanian599]

What is rule for the core size selection

[@purnasahoo791]

Sir, Ty so much. It very helpful for me. Sir plz make a video about earth fault protection and it calculation.

[@electricaltechnologyandind5335]

Already there

[@purnasahoo791]

But it was about restricted earth fault but i say about motor earth fault current calculation.plzz

[@milanmukherjee9425]

Great sir.please make a video on NPS relay,and it's setting calculation.please

[@suresh.kmuthu7644]

Hi. Thnks for the video.one more request pls explain how to choosen the CT VA rating for protection & metering.

[@gustavomarcelo7250]

Hi. Means that we will have two CT of : 1. 3200/1,5P20 2. 3200/1 ?

[@electricaltechnologyandind5335]

Actually two core...... Yes.. correct

[@balrajsubash282]

Hi For 5P20 class the fault current more than 20 times what will be the error on secondary side?

[@itsickdar7844]

perfect

[@deepalps]

Thanks a lot for valuable information Kindly give transformer winding details for eg 440/110V 15VA

[@sabarinarayanan4357]

Put videos about vfd and vsd

[@balakrishmam]

Great video 👍. One small suggestion. Always we are not getting bell icon button in the videos. Please include from next video. Thanks.

[@electricaltechnologyandind5335]

Press the subscribe button. Then you will get the bell icon. I don't do any thing else to create subscribe links. So you won't find it in my videos. Your love ia everything.....

[@balakrishmam]

I have already subscribed and pressed the bell icons also. Don't know why I can't receive the eye buttons link. However thanks for the reply.

[@rukmagoud]

Sir u just informed PS class . You didn't explain about knee point voltage and formulas

[@electricaltechnologyandind5335]

It is available in my restricted Earth fault protection vides

[@sudhansusamal8886]

2000 where came sir please answer

[@elxanmusabayev4930]

Why you have been using 0.433 kV when calculated CT ratio, but 433 V when you calculated transform current?

[@electricaltechnologyandind5335]

Trafo current is based on 433 V. Load currents are based on 415V. 433V and0. 433 kV are same i believe

[@udayakumar5379]

Hello sir, can you given me the explanation of how did you identity 5% or 10% error..?

[@electricaltechnologyandind5335]

That is a part of ct design. I haven't explained ct design here....

[@balasubramanian599]

How to select the core size

[@electricaltechnologyandind5335]

That is for CT manufacturer

[@mazharalibarodawala6999]

How to calculate burden of CT??

[@mdtarique6305]

Manufacturer wll provide how to calculate , ( data provided)

[@patelkaushik2996]

SIR APKA VIDEO BAHUT A6A HE LEKIN AAP HINDIME BHEJONA

[@amargaikwad3151]

In short explain a lot

[@syedmohammadsaif8344]

Better Explain from basic ,no matter video long

[@electricaltechnologyandind5335]

But i usually explain general industrial practice. Not basic..... Hope you will understand....