Cylinder head cover gasket replacement, Peugeot 207cc 1.6 vti

  Рет қаралды 26,244

MrFxr

MrFxr

Күн бұрын

Пікірлер: 56
@patrickmccarthy6532
@patrickmccarthy6532 9 ай бұрын
Great video very helpfull not just the vid but comments too so thank you very much.
@mrfxr1695
@mrfxr1695 9 ай бұрын
Thanks 👍🙂
@sicks6six
@sicks6six 4 ай бұрын
rocker case they are called in the UK for anyone getting confused, a smear of instant gasket silicone in the recess helps a lot in keeping it in place as they often fall out when refitting them,
@thomobrien247
@thomobrien247 8 ай бұрын
Hey thanks for your video. I just picked up an old Peugeot 308 1.6 petrol (2009) for my girlfriend to learn to drive in. It came with the P0014 and depollution fault. I was about to change the solenoid but when I checked the spark plug reservoirs 2 of them were full of oil. I have just purchased a new rocker gasket and will use your video to help when it arrives. I was worried it might be the head gasket at first. Did you find out more about the white sludge? Was it the head gasket? Thank you
@mrfxr1695
@mrfxr1695 8 ай бұрын
Thanks, take it easy and will be all good. White sludge was worrying for a start, but I noticed that was coming and going ( it would show on underside of oil cap as well). Apparently there engines can condensate within timing chain housing if ruin on short journeys. On longer runs moisture will evapurate completely. Apparently it is normal. I've had no other issues with it Regards to p0014, it could be that exhaust solenoid is just clogged up. It is very sensitive on oil. Wrong viscosity or old dirty oil can cause issue. Cleaning solenoid valve and changing oil and filter often sorts it
@OKuusava
@OKuusava Жыл бұрын
Great video. If I guess you desided that exessive oil consumption was from these gaskets? -and: did this change make the change on that? We have same engine on our Citroen Gran Picasso, and it drinks nowadays abt 2-3 litres yearly, on 10-15kkm driving.
@mrfxr1695
@mrfxr1695 Жыл бұрын
It halved oil consumption for me, these engines still use fair amount of oil even when everything is good
@mazhaerexpert
@mazhaerexpert Жыл бұрын
Bud, You must be a real Christian to help people like this. I don’t have this car but if I would have one, your video would mean great value 🎉
@mrfxr1695
@mrfxr1695 Жыл бұрын
Thanks 👍 I'm trying to☦️
@hypxrzen6087
@hypxrzen6087 Жыл бұрын
I have the problem of the rubber falling off the Cover.. Can i also glue it onto the cover or maybe place the rubber on the block??
@mrfxr1695
@mrfxr1695 Жыл бұрын
You can use a smear of HT silicone to hold it
@hypxrzen6087
@hypxrzen6087 Жыл бұрын
Thanks ill try that out..@@mrfxr1695
@psr1133
@psr1133 11 ай бұрын
Really good video. But you didn’t show how to remove the fuel line and I’m not sure how to remove it
@mrfxr1695
@mrfxr1695 11 ай бұрын
There should be a plastic retaining clip ( white if I remember correct) that has to be released, just be careful not to lose it if it comes all the way out
@psr1133
@psr1133 11 ай бұрын
Thanks. Do you need to depressure the fuel like before removing it?
@mrfxr1695
@mrfxr1695 11 ай бұрын
@@psr1133 not really, it's a low pressure feed pipe. The only thing to keep in mind, after reconnecting you'll have to turn ignition key to contact position (without cranking engine) to power fuel supply pump so it can purge the air Happy New Year
@psr1133
@psr1133 10 ай бұрын
I have managed to remove the clip and change the new seal and put everything back together. However, I have lost the clip in somewhere in the car as it fell down haha. Do you know where I get a new clip?
@mrfxr1695
@mrfxr1695 10 ай бұрын
@@psr1133 in glad you've managed to complete it. I've lost a clip once but managed to find it on top of engine subframe. I would imagine you could get it from Peugeot dealer, official service. It shouldn't be expensive
@ventsislavivanov4542
@ventsislavivanov4542 Жыл бұрын
Hi , great video , is there tourgue spec's for the bolts ? Thank you
@mrfxr1695
@mrfxr1695 Жыл бұрын
This is what I've managed to find on the net. "There is a specific order for tightening these bolts which is from the centre to outer and the torque quoted in Haynes Manual is 10 Nm = 4 lb.ft. "
@ventsislavivanov4542
@ventsislavivanov4542 Жыл бұрын
@mrfxr1695 you are star 10 nm
@mrfxr1695
@mrfxr1695 Жыл бұрын
@@ventsislavivanov4542 thanks 👍🙂
@mariansandu2451
@mariansandu2451 6 ай бұрын
Dacă tot ai scos capacul de culbutori de ce nu ai curățat și solenoidul din spate?scuze că te-am întrebat din pură curiozitate!
@mrfxr1695
@mrfxr1695 6 ай бұрын
I didn't had a problem with it 🙂 if it's not broke don't fix it 👍
@mariansandu2451
@mariansandu2451 6 ай бұрын
Ok am înțeles !mulțumesc pentru răspuns !
@mariansandu2451
@mariansandu2451 6 ай бұрын
Am un peugeot din 2013 și-mi afumă bujiile nu sunt cu ulei doar afumate și le schimb,la relanty dacă stau cu ea pornită 10/12min.la plecare după loc scoate fum alb după care dispare poate fi vvt-ul?
@mrfxr1695
@mrfxr1695 6 ай бұрын
Hi, I'm not sure if I understood it correctly. Smoke on start up that clears away could be failed valve stem seals. Usually issues with vvt would result in engine fault codes. Have you run diagnostics, any codes?
@mariansandu2451
@mariansandu2451 6 ай бұрын
Mulțumesc! Nu an făcut o diagnoza,am să fac dar nu știu ce înseamnă tijă de supapă (poate fi semeringurile de supapă?) AM desfăcut vvt-ul din față pe care lai arătat în clip și nu am putut să scot sita dar la-am curățat cu soluție de frână și tot așa face adică tot îmi afumă bujiile mai mult la piatonul1.Mulțumesc pentru răspuns!
@mariansandu2451
@mariansandu2451 6 ай бұрын
Am o rugăminte !poți să-mi spui la motorul ăsta de 1.6 88kw 120cp peugeot 308sw ce compresie trebuie să fie ?mie mi-a ieșit 9 pe toate 4 pistoane,Mulțumesc anticipat!
@mrfxr1695
@mrfxr1695 6 ай бұрын
​@@mariansandu2451yes, valve seals
@mrfxr1695
@mrfxr1695 6 ай бұрын
​@@mariansandu2451I believe that's too low. Have a look here www.car.info/en-se/peugeot/308/t7-16-vti-m5-6650187#specs
@muhammadfirdausmeran4831
@muhammadfirdausmeran4831 8 ай бұрын
hye ., need to remove battery terminal or not ?
@mrfxr1695
@mrfxr1695 8 ай бұрын
It is always a good practice to disconnect when you're doing any sizable work on the engine, especially that engine( it will give you more room for work)
@antanasmaciulskis8454
@antanasmaciulskis8454 Жыл бұрын
would leaky cover gasket result in blueish fumes coming out of the exhaust when accelerating?
@mrfxr1695
@mrfxr1695 Жыл бұрын
Probably not, bluish smoke is generally caused by burning engine oil. Either piston rings are worn, could be head gasket, turbo issue, pcv valve, engine oil level too high... If only present at start up, then I would suspect valve stem seals It all depends on amount of smoke and how often it happens Sometimes bad ignition and overfueling can make unburned fuel to cause smoke on heavy acceleration
@antanasmaciulskis8454
@antanasmaciulskis8454 Жыл бұрын
@@mrfxr1695 thanks for replying. I know for sure I overfilled it with oil by mistake, its more than full right now, so that might be causing the excess amount of smoke
@mrfxr1695
@mrfxr1695 Жыл бұрын
Please reduce the oil level to below max mark on dipstick, it can cause you long term issues with the engine.
@derufer2328
@derufer2328 Жыл бұрын
How many kilometers does the car have?
@mrfxr1695
@mrfxr1695 Жыл бұрын
Just over 70K miles, about 115-120K Km
@ВикторКозловский-й5о
@ВикторКозловский-й5о Жыл бұрын
Сколько льёте масла в этот двигатель спасибо
@mrfxr1695
@mrfxr1695 Жыл бұрын
4.25 lit 5w30 fully synthetic oil
@ВикторКозловский-й5о
@ВикторКозловский-й5о Жыл бұрын
@@mrfxr1695 большое спасибо а 10w40 можно заливать в этот двс
@mrfxr1695
@mrfxr1695 Жыл бұрын
@@ВикторКозловский-й5о 10w40 oil is much thicker and can cause issues with vvti system and hydraulic valve lifters. I would use 5w30, especially in colder weather
@ВикторКозловский-й5о
@ВикторКозловский-й5о Жыл бұрын
@@mrfxr1695 Thank you for prompt reply
@ReyGosten
@ReyGosten Жыл бұрын
Thank you for sharing, I have the saw problem.
@mrfxr1695
@mrfxr1695 Жыл бұрын
Thank you I wish you an easy and successful repair 👍
@Tomasso1977
@Tomasso1977 Жыл бұрын
This is the valve gasket, not the head gasket. However, job well done.
@mrfxr1695
@mrfxr1695 Жыл бұрын
Of course, it is not head gasket. It is head cover gasket, or valve cover gasket, or cam cover gasket or rocker cover gasket,.... 😉 All the best 👍
@luisdariorobledo7010
@luisdariorobledo7010 4 ай бұрын
😮
@1683Jordan
@1683Jordan 4 ай бұрын
Hey how many NM do I need to use while tightening the bolts back please? 😊
@mrfxr1695
@mrfxr1695 4 ай бұрын
not a lot, I beleive it is only 10 Nm. My torque wrench starts at 20 Nm so I just tighten them by hand (feel) with spanner
Partie 3 : Mise en place de la culasse du 1.6 VTI 120
12:14
Le Cliquet Express
Рет қаралды 8 М.
Why no RONALDO?! 🤔⚽️
00:28
Celine Dept
Рет қаралды 99 МЛН
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 16 МЛН
Миллионер | 3 - серия
36:09
Million Show
Рет қаралды 2,2 МЛН
How to Fight a Gross Man 😡
00:19
Alan Chikin Chow
Рет қаралды 20 МЛН
Peugeot 207 1.4 vti Valve Cover Gasket replacement P1336
19:20
Watch and fix
Рет қаралды 53 М.
Peugeot 308 1.6 Hdi Valve Rocker Cam Cover & Gasket Replacement
11:55
O'Rileys Autos
Рет қаралды 13 М.
Peugeot 207 1.6 VTI, Abgas system defekt, resio problem.
18:47
Mravic's Garage
Рет қаралды 23 М.
Установка Гбц Ситроен С4 двигатель EP6.
27:15
Rear door leak on Mini R50 R53, locating and repair
37:30
(Part 1) How To Repair Peugeot 207 And 307 1 4 Litre Engine, ( Leaking Headgasket ) Engine Code: KFU
36:03
Remedy Motors #HowToSaveMoneyOnCarRepairs
Рет қаралды 12 М.
Why no RONALDO?! 🤔⚽️
00:28
Celine Dept
Рет қаралды 99 МЛН