Dangerous 3" Super Magnet Unboxing and Safety Testing

Here is how a 3 inch, 350 pound pulling force Neodymium Magnets is shipped and some different metal, safety test I ran before taking it out in the field or around my kids. The pull force steadily builds to crushing strength.
Here is the magnet used in the video: amzn.to/3lfs9Co
you might be able to find one stronger and cheaper on Amazon by shopping around starting from this link.
Check out my new followup video, 350lb Force Super Magnet? Prove It here:
• Risky Testing of 350 l...
Music: Europa by: / teknoaxe
#supermagnet #unboxing #testing
I'm an Amazon affiliate and clicking on the above link(s) provides a small percentage to the channel via Amazon at no additional cost to you. Thank you for your support.

[@Swizzle9708]

Guys stop with hate, he’s just a guy that bought a powerful. magnet and thought it was cool

[@MakeItorBreakItNow]

Chace, thanks for the feedback and kind words.

[@Gadgetmall]

That's awesome. See video of the half a foot block n52 . 5000 pound pull.also if you stick it to real iron or your lawnmower flat surface you won't be able to pull it off I have one half that size and it will pull my 62 inch woods mower with a big metal grasscatcher about 600 pounds of mower. all over the yard with the truck. We finally got it off by beating it with a rubber hammer till we could get it to an edge then we could pull it off. And I'm strong and 61 years old can pick up 200 pounds. These are amazing when attached to pure steel or iron. The hook and screw btw is not pure ferrous metal is why it's got a weak pull..

[@MakeItorBreakItNow]

Gadget, thanks for your comment and feedback. Agree, using the magnet on pure ferrous metal works best.

[@potatosaladman5174]

sharp magnetic knife next to a strong magnet. Seems safe

[@Javier-kg2ev]

3 year late ratio

[@bang1338]

@@Javier-kg2ev same

[@MindKontrolleProject]

I'm not an arm chair Physicist like some of your commenters. This video is for general KZbinrs. That being said... I like the rolling metal ball "thingy's" on the tape measure "thingy" test. Good visual reference 👍

[@MakeItorBreakItNow]

Thanks Mike, it wasn't meant to be serious. Always interesting the range of comments a video will get.

[@johnrobinson6449]

I'm guessing that the eye-bolt that came with it is stainless steel. Depending on which alloy of stainless steel could greatly reduce the magnetic attraction making the eye-bolt much easier to remove from the magnet.

[@MakeItorBreakItNow]

John, thanks for your feedback. Agree with your comment, spot on.

[@johnrobinson6449]

Hey dude, you did just fine. I don't mind your mispronunciations one little bit. 9 out of 10 people will mispronounce Neodymium. These are a bunch of armchair critics that don't have the curiosity to even try these things, and a bunch of "I'M MISTER PERFECTS" that have nothing better to do than criticize others. I was a machinist and I applaud your use of a straight blade screwdriver to tighten that screw as a #4 or larger Phillips drivers are relatively uncommon. AS A MACHINIST I would have done the same thing if I didn't have the right tool. What I like about you is that you are curious, friendly, and will happily share your experiences. You have far more personality than all of the armchair critics that have nothing better to do than piss on others. Good for you! "Illigitimi Non Carborundum!" That's a mock-Latin aphorism meaning "Don't let the bastards grind you down!" I'll probably end up with 10 of these idiots telling me I got the Latin wrong. They can all clean the slippery end of my dipstick.

[@MakeItorBreakItNow]

Thanks John again for the positive waves, you are a good soul.

[@casorwhtever3478]

Im subbing cause your channel is cool keep up this good and cool work!!!

[@MakeItorBreakItNow]

Raspberry production s, thanks for the comment and feedback.

[@ChingFong58]

Just wanted to say that the diameter of the magnet is inside the black sealer. The outside is the casing. So it's really about a 2 1/2" magnet.

[@MakeItorBreakItNow]

GeneF, Valid point.Thank you for the comment.

[@royrice8597]

Doesn't affect phones or watches either. I tried it! All all 👍👍👍

[@MakeItorBreakItNow]

Roy Rice, thanks for the feedback. I'm assuming you are referring to digital watches.

[@Jasman35]

Looks like the outer layer is a shielding to weaken all but one of the poles, glad you added the grams weight btw (metric)

[@MakeItorBreakItNow]

Jasman35, thanks for the comment. Could very well be on the shielding.

[@shade1114]

Hey all you negative people leave him alone. He is doing an awsome job. I bet some of you don’t even know what is like to put a show together knowing jerks like alote of you are out there so give him a brake I thought it was good.

[@MakeItorBreakItNow]

george, thanks for the positive feedback. Agree, putting videos together are not always easy. Always striving to get better.

[@shade1114]

It was my pleasure. I have subscribed and can’t wait for more videos

[@MakeItorBreakItNow]

george, thanks for subscribing, I strive to post a new video each week. Always have several projects going on in parallel.

[@RaDrumba]

Now the Stainless steal bolt is high quality. The more pure Stainless steal the less magnetic it is. Number on that thread is pureness value.

[@MakeItorBreakItNow]

Ra Drumba, thanks for the additional info on stainless steel, much appreciated.

[@AdamsBrew78]

Recently got a 290lb magnet.. it’s not as powerful as I’d imagined it’s be. I can easily hold metal in palm of bare hand or fingers, with magnet on the other side, without the force being painful (though gotta be careful about skin being pinched) .. I’m really curious about the 600-1200lb monsters .. Would the constant pressure cause serious damage? I know the real danger is from accelerating objects,

[@MakeItorBreakItNow]

Adams Brew, thanks for your comment. Agree the real danger is accelerating objects. But with larger size magnets like what we're talking about here I think long term static (constant) pressure would be a problem because eventually you would shift say your hand the the pinch factor would be high. I'm not willing to take that risk but interesting question.

[@Mr_Cookie239]

“Neobinium” that mentally hurt me the whole video

[@MakeItorBreakItNow]

Blake, sorry about that. I'll try to remember to get it right during my future super magnet videos.

[@ohiohouston3560]

Make It or Break It don't worry about it. Neodymium is a ridiculous word

[@TheSebastian9000]

BlakeMeyer239 he said allumilum too.

[@cdwblobboy]

sillynium next XD

[@TheAdulter]

BlakeMeyer239 ikr

[@WinWin-pz9wq]

I have a giant neodymium magnet to, it is 9cm or 3.5 in wide and 2 cm or 0.75 in tall it’s pull force is 300 kg or 661 lbs !

[@MakeItorBreakItNow]

Win Win, your magnet sounds awesome have you gone fishing with it? Check out my new design: kzbin.info/www/bejne/qZ6YlZWcpdaUjNE

[@MakeItorBreakItNow]

Check out my new followup video, 350 lb Force Super Magnet? Prove It here: kzbin.info/www/bejne/rYnQlIqka7uHaas

[@MakeItorBreakItNow]

Here's a link to the video where I step you through how I made my fishing rig using the magnet you see here. Check it out: kzbin.info/www/bejne/aILUmJiCmp18gcU

[@southyorkshiretreasurehunt8513]

nice i have a 400kg one i use for magnet fishing

[@MakeItorBreakItNow]

brandon slingsby, how's the bigger magnet working for you? I've seen folks lose larger magnets because they clamp onto to something like a conduit pipe and the rope breaks...

[@southyorkshiretreasurehunt8513]

@@MakeItorBreakItNow its sound, if i get the magnet stuck i just chuck a grappling hook in after it

[@southyorkshiretreasurehunt8513]

@@MakeItorBreakItNow i use a thicker rope, it is like 3 of them ropes put next to one another

[@MakeItorBreakItNow]

@@southyorkshiretreasurehunt8513 you got some good solutions there, thanks for sharing.

[@southyorkshiretreasurehunt8513]

@@MakeItorBreakItNow sound m8

[@luxuryviplifestyle9494]

Trillions like and best comment for you because you are best on Earth and follower respect you,we need videos in Real 120fps or 240fps 4K,8K and Sound in FullHD Surrounded

[@MakeItorBreakItNow]

This video was published at 1080pHD, most all my videos are HD. Thanks for your comment.

[@Prunesqualler]

For the folks who like the metric system? United States, and Belize are the only countries still using the Imperial system of measuring.

[@jesusborrego3270]

Do you know the history of why we measure in feet?

[@steve-o5793]

Think the eyelet and screw are stainless that's why they don't stick that strong.

[@MakeItorBreakItNow]

Steve, maybe so. Thanks for the suggestion.

[@rese31e]

Steve Yoshikawa I was gonna say the same thing.

[@stevebrown7133]

Steve Yoshikawa also they would be somewhat magntized. From sitting with the magnet for so long shipping

[@logantauber322]

Steve Y nah dude this gust is just a fucking idiot

[@acto_surge5305]

Steve Y yea

[@southyorkshiretreasurehunt8513]

i have the exact same magnet its dope

[@MakeItorBreakItNow]

oh yeah yeah, thanks for the comments. New magnet fishing design coming soon.

[@MakeItorBreakItNow]

Check out my newest super magnet video: Super Magnet Sculpting Toy, How to Make One, Easy DIY by clicking here: kzbin.info/www/bejne/aKrKdmyKf9hlfNE

[@himabinduandey]

NeoBinum is the right way to pronounce it righttt? Or is it NEODYMIUM

[@MakeItorBreakItNow]

Hima Bindu, you found the Easter egg! Every video I make has one. Good job.

[@himabinduandey]

@@MakeItorBreakItNow yay

[@MakeItorBreakItNow]

@@himabinduandey bonn chance!

[@ianmangham4570]

Very funny, take it easy and take care of yourself

[@MakeItorBreakItNow]

Ian Mangham, thanks for the comment. I'm glad you saw this video in the light it was intended.

[@scottandrasi6703]

Yes let's put something you have to screw with a screwdriver on a magnet. Manufacturer: "On the most powerful side!" Proceeds on putting in the instructions "Please screw in with a FLAT screwdriver"

[@uuooctium1182]

There are different grades of neodymium, but the pull force isn’t 300lbs for everything. It’s pull force over a flat surface that covers the whole face of the magnet is what they measure, not some random small object.

[@MakeItorBreakItNow]

GammaRay326, thanks for the feedback and valid point. Check out my new followup video, 350 lb Force Super Magnet? Prove It here: kzbin.info/www/bejne/rYnQlIqka7uHaas where I do just what you mention above.

[@magneticmisadventures6340]

I'm subbed already. I would recommend a lock washer between the eye bolt and magnet. I have one on mine.

[@MakeItorBreakItNow]

that's a great idea, I think I'll give the lock washer a shot. Thanks for the suggestion.

[@MindKontrolleProject]

yup... thread locker as well.

[@luhandregrobler6197]

Dad is going to have a good night

[@rem6607]

the hook is a special material. its lightly magnetic and there will be no rust at the hook

[@tannervlogs5208]

Keep up the good work

[@MakeItorBreakItNow]

thanks Tanner, appreciate the feedback.

[@teelaloyot7936]

Tanner Vlogs I agree

[@MakeItorBreakItNow]

Thanks Teela for the positive feedback.

[@Waterdog5779]

Thanks for the info. I'm thinking about getting a 5 hundred pound one.

[@MakeItorBreakItNow]

Lewis Kingsley, thanks for the comment. Good luck with your fishing. I've been thinking about getting another magnet also, although probably not a 500 lb force one.

[@ph143aaf]

Between "Neobinium" and watching this guy try to put the flat head screwdriver in the phillips screw, I literally wanted to beat the stupid out of my own head because I was afraid it might spread... and then he called his ruler "alubimum"..... Smfh.

[@ianmangham4570]

Trippy 😀

[@ianmangham4570]

@Brady Hartsfield Don't be Landon 🤣

[@aussiezx3017]

i got 2 x 400kg one silly me they connect 1 blow up set my pant on fire waste $45 so stuck 2 together now super magnet be very careful they hurt finger stuck middle. i found only out side they stick too magnet the middle no stick but get 2 put together they work so much better.

[@MakeItorBreakItNow]

aussieexxy kane, thanks for leaving a comment. Agree these magnets can be very dangerous.

[@jinxjones5497]

the magnet's hardware is maybe stainless steel which may have no attraction and attraction on different parts of the same piece

[@aliasfred]

You need to put some "thread locker" on that eye bolt.

[@MakeItorBreakItNow]

Larry, will do. Thanks again for another tip.

[@drewby4563]

Yes I've purchased 1 myself haven't had time for magnet fishing yet lol

[@keyboardwarrior2812]

Thanks for that mate you got a thumbs up from me

[@MakeItorBreakItNow]

Keyboard Warrior, thanks for the comment and thumbs up. Much appreciated.

[@rayluc100]

Use Loktite (red) to keep threads tightly cinched.

[@MakeItorBreakItNow]

rayluc 100 thanks for the suggestion, I'll try it out.

[@sammich8295]

Jeez put some positivity in your lives people so what he made some mistakes calm down ;-;

[@Dano-uf8ys]

Well on the one hand he's a pretty boy but on the other he is a damn fine actor. So take it as you will. I look like Ozzie myself.

[@MakeItorBreakItNow]

Dano1947, thanks for brightening my day.

[@demonetizedhistory5806]

I thought he was gonna correct 'neobimium' at the end but I thought wrong.

[@MakeItorBreakItNow]

what can I say, its a trip word for me. In follow on videos I did correct the way I said it. Thanks for you comment, always appreciated.

[@coconut6680]

The hardware must be somewhat of aluminum. It looks really strong. Cool video. Keep up the good work. Much love from Hawaii. Aloha

[@MakeItorBreakItNow]

Coco Nut, thanks for the feedback. Glad you enjoyed the video.

[@ryanburch26]

Stainless

[@tricksfun2778]

I ordered one from AliExpress Waiting for it to arrive

[@MakeItorBreakItNow]

Interesting, did you get a good price? I'm in the market for another magnet.

[@tricksfun2778]

@@MakeItorBreakItNow D60MM - 14.10 dollars 112-150KG D75MM - 160-200KG 23.34 dollrs

[@MakeItorBreakItNow]

@@tricksfun2778 that is a good price. Smart buy.

[@tricksfun2778]

@@MakeItorBreakItNow thanks I loved your video with the magnetic experiment👍🏻👍🏻👍🏻

[@MakeItorBreakItNow]

@@tricksfun2778 stay tuned for more to come. I use magnets in my builds all the time.

[@waterchestnutful]

Great video :) ignore negativity

[@MakeItorBreakItNow]

Ra Lu, thanks for the positive feedback. Always appreciated.

[@blueskeleton7744]

Wow..pretty cool. Maybe next vid you go fishing? See what kind of crap you can find chucked in the waters.. my son found a little one but dang if it is powerful..we will try our luck fishing. We'll see what he gets too.. be safe y'all, kind words only to those demonstrating .. unpredictable but fun to watch. Blue

[@MakeItorBreakItNow]

Blue Skeleton, thanks for your comment, you can check out my fishing videos here: kzbin.info/www/bejne/aILUmJiCmp18gcU and here kzbin.info/www/bejne/b6qrgZaCnt5qlZo and here kzbin.info/www/bejne/h56lk4WPjNRnb8U

[@PrithwirajBose]

neoBinium! Carpenter to Physicist!

[@nichols1741]

I wish it was hung from a good chunk of steel and did a pulling weight test. The entire surface of the magnet attached to steel would be the test of did he get ripped off or not.

[@magneticmisadventures6340]

Right. I have tested my 480lb magnet with pure steel plate and it is extremely hard to get off.

[@stonerdude4611]

Strange Amazon should have put a label that it can't ship by air freight just land freight only. A magnet properly shipped should be in Styrofoam not butcher type paper. Amazon is slipping on FAA rules.

[@MakeItorBreakItNow]

Kevin Perry, a very good point, thanks for the comment.

[@JedFinds]

5:51 ooooo that sound

[@MakeItorBreakItNow]

Jed Finds, yeah its a bit scrapey, will now probably use that in one of my Halloween builds. Thanks for the feedback.

[@JedFinds]

No problem! Loved the video by the way. I liked the tape measure part the best haha

[@newguy2794]

It would seem to me that the "warning label" should have been on the outside of the box rather than on the inside. Its a bit late to give a warning after the box is open.

[@MakeItorBreakItNow]

Agreed. Never really thought about it that way...

[@nestorgalo8889]

Directionally drilling into a barrel and enriching my fishing line

[@MakeItorBreakItNow]

Nestor Galo, thanks for the feedback and comment.

[@jaycee8459]

Would this stick to a metal filling? That would SUCK

[@royrice8597]

Magnets do nothing to computers. I tried it!! All aok . 👍👍👍

[@MakeItorBreakItNow]

Roy Rice, thanks for the feedback on your computer test, interesting.

[@Tahoza]

Did you hang the camera from the ceiling? Is that the swaying I'm seeing?

[@MakeItorBreakItNow]

I did, and have since gone to a whole new camera rig setup.

[@gergemall]

Locktight on threads is helpful

[@MakeItorBreakItNow]

JON Gergeceff, great idea, I think I'll try some Locktight before I go out fishing again. Thanks.

[@cameronlindsay1329]

Is there any type of gloves you recommend to wear when handling with these magnets?

[@MakeItorBreakItNow]

Cameron, leather work gloves or thick water proof gloves are best to use with these magnets. Here's some examples: amzn.to/3fkp1Ey or amzn.to/31lhpcH

[@400smallblock]

Probably a good idea to blur out your address when showing stuff that's been shipped to your house man. If I can read your city, state, and Zip....the street name and house number are printed much bolder. Just trying to look out and make ya aware my man. Aldie, VA 20105...blur out the small square "handling label".

[@brianthomason5022]

Everyone might send em some poop from poopsenders.com. trust me its a thing

[@HariharaprasadVellala]

I was thinking that you will tell about some uses of the magnet and demerits.

[@MakeItorBreakItNow]

Thanks for the feedback. See the Make It or Break It links below for other super magnet videos I've recently made that go into the details you're looking for.

[@WilliamSmith-dg5re]

DANGER DANGER IS A MAGNET FOR GOD SAKE

[@MakeItorBreakItNow]

William, very much so. Thanks for your comment.

[@mousescorp]

They lessen the magnetic property on the eyebolt for easier mounting and unmounting .... just fyi

[@MakeItorBreakItNow]

mousescorp, thanks for the feedback. I'm curious how you found this out.

[@mousescorp]

A little of experience and a smaller amount of common sense :)

[@MakeItorBreakItNow]

Check out my new video where I go magnet fishing with this rig in the ice cold waters of the Adirondacks: kzbin.info/www/bejne/b6qrgZaCnt5qlZo

[@michaelanderson9792]

Yes two 250lb pull magnets slammed together pinching my palm got a welt under my middle finger ouch be careful out there

[@MakeItorBreakItNow]

Michael, Thanks for the tip. Agree, these magnets can really hurt if you're not careful.

[@MakeItorBreakItNow]

for those who have asked here is a link to the magnet I have for all those who have asked: www.amazon.com/gp/product/B01JK20IR8

[@MakeItorBreakItNow]

plants247 you're welcome. Thanks for the reply.

[@MakeItorBreakItNow]

plants247, thanks for subscribing.

[@m4rdoo]

Dang...click baited by the thumb nail lol

[@compressedfilms]

Does not look that strong, I have one that I paid £30 for. I use it to secure heavy objects whilst welding, It works allot better that the ones sold for purpose. If I was sitting at the table with it, there is no way I would have ball bearings or any other tools around, they would take off like a rocket towards the magnet. I have a thin piece of foam glue to the surface of mine to absorb impact.

[@MakeItorBreakItNow]

compressedfilms, thanks for the feedback. The magnet is stronger than you might think, check out this video to see the test I did last weekend: 350 lb Force Super Magnet? Prove It here: kzbin.info/www/bejne/rYnQlIqka7uHaas I like your idea on the thin foam, thanks for sharing.

[@magnetfishingexploringaust7304]

thanks.... worth watching.

[@MakeItorBreakItNow]

Thanks Alison, Eti & Josh

[@terryglenweaver]

My finger is still healing after receiving my 1,000 lb force magnet. (They did not tell me it would want to close my car door from 1 foot away.) I had an extremely minor incident.

[@philfrederickiii2320]

Run the rope through a cut plastic pop bottle and doing so will keep the magnet from snagging on logs.

[@MakeItorBreakItNow]

Phil, That's exactly the design used. Thanks for the feedback. Here's the video: kzbin.info/www/bejne/aILUmJiCmp18gcU

[@jraymond3218]

Don't get all the negativity.Thanks for the vid.

[@MakeItorBreakItNow]

J Raymond, thanks for the positive feedback. Some of the comments are surprising, but that's KZbin.

[@DirectorsCut25]

Nice video my friend

[@A13-x3l]

I swear I thought he was going to poke his eye out with that flat head.

[@armandosalinas1326]

Anyone else waiting for the screw driver to fly at his hand

[@MakeItorBreakItNow]

Armando, it did. You have to be careful out there...

[@stephaniepowers4327]

Good job

[@MakeItorBreakItNow]

Thanks Stephanie, appreciate the positive feedback.

[@camcorder8203]

I mean you did order the magnet through Amazon prime, it's probably gonna ship quick

[@MakeItorBreakItNow]

Deep Bass, thanks for the feedback. Yes, I did say it right in the follow up videos below. Thanks for watching.

[@camcorder8203]

Enjoyed it

[@anthonymoon6918]

Do they break apart easy? Should u sheath it somehow before fishing with it?

[@MakeItorBreakItNow]

Anthony, my magnet has a steel cover on everything but the bottom which has protected it well so far. Check out my magnet fishing setup here which I think will answer all your questions. kzbin.info/www/bejne/aILUmJiCmp18gcU good luck. Here's my magnet fishing video where I actually use the rig: kzbin.info/www/bejne/b6qrgZaCnt5qlZo good luck

[@richardkuhn3330]

Just to let you know that that was a Philips head screw not a flat head

[@johnrobinson6449]

Just to let you know I was a professional machinist and if I didn't have a #4 or #5 Phillips bit in my tool box I would have done exactly the same thing he did. What amazes me is that I need to let YOU know that he KNEW he had the wrong kind of screwdriver. And I just need to let YOU know that your "information" was pointlessly condescending. You must be PROUD!

[@chrismoore7359]

I'm guessing you didn't have some 45lb steel plates lying around a bench to really test it?

[@MakeItorBreakItNow]

Check out my new followup video, 350 lb Force Super Magnet? Prove It here: kzbin.info/www/bejne/rYnQlIqka7uHaas

[@rhetthouse432]

The bubble wrap just keeps the neodenium magnet from bouncing around I guess. What's an inverse square law? It ain't square, it's round. And the law ain't got nothin to do with this!

[@alexispellitteri7297]

I don't know how hevey a 85 Honda big red 3 wheeler 250cc is but I pulled one with all the tires flat and I have the same magnet

[@ianmangham4570]

Around 400 pounds

[@uldaricogorgod3152]

Good pm ,where.can i.buy the magnet what name store here in manila,.thank you refly pls.

[@MakeItorBreakItNow]

Check the main info section below the video.

[@rjamespathfinder8474]

Your review missed the big part of what the magnet claims; 350 lb capacity. You should have proven it can really hold a weight of 350 lb by hanging a couple of weights.

[@MakeItorBreakItNow]

Rex Pfynder, yup. Did what you're asking in this video here: kzbin.info/www/bejne/rYnQlIqka7uHaas

[@joeloresajo6510]

0:15 When you forget what something does and you trim the video.

[@BuildaPC4life]

Lil overkill with those gloves

[@MakeItorBreakItNow]

RC Racing Twente, maybe so, that video is several years old.

[@billtaylor1439]

put the cardboard box in your recycling and pop the bubble wrap and stuff into your plastic grocery bag so it can be recycled at your local grocery store.

[@kennyb3524]

Was anyone else watching the knife? Lol

[@stonerdude4611]

So you keep it in Styrofoam. my 837 lb runs $ 40.00, You don't have a Philips head screwdriver its like putting a square peg in a round hole.

[@MakeItorBreakItNow]

Kevin Perry, thanks for the feedback, I'll try to do better next time.

[@simoncunningham3740]

that metal loop thing that came with it will probs be a cheap stainless so very little iron very weak pull

[@MakeItorBreakItNow]

Simon, the loop is actually stronger than the magnet, check out this video to see: 350 lb Force Super Magnet? Prove It here: kzbin.info/www/bejne/rYnQlIqka7uHaas

[@simoncunningham3740]

Make It or Break It no I mean it being stainless is why its not getting much of a reaction from the magnet, maybe cheap was the wrong word, but not 100% stainless as the magnet is still trying to grab it

[@johnrobinson6449]

SimonCUnningham. There are many grades and alloys of stainless, each having different properties. In the machine shop my first test of an unknown stainless alloy was a magnet test as stainless alloys are broken down into 2 major groups being "Magnetic" or "Non-Magnetic". And even within both groups there are variations of just how strongly they are attracted to a magnet. And ALL those alloys are considered to be 100% stainless steels as they all have an iron base and then alloyed with other non-corrosive metals and carbon in varying degrees and combinations. One example of the differences is that if you have an Induction cook-top stove and want to use stainless cookware, the pot or pan MUST be made out of Magnetic Stainless.

[@joejee01]

magnetic trainwreck ^v^ I subscribed lol

[@9023710a]

Neobinium? Perhaps you ordered the wrong type, try the stronger neodymium magnets

[@mortuus4601]

Why dont u shut The fuck up!?

[@thenotoriousrvh6091]

If I had his mentality lol maybe I wouldn't be in debt, cause I can't call $36.95 alot of money.

[@ano2101]

Gtfo you look like that’s a shit ton of money for you I mean look at your glasses lmfaoooo

[@Mark-xh1jw]

Because the eyebolt has more aluminum in it then ball bearings

[@Dano-uf8ys]

Damn dude you look like Gordon Clapp from NYPD BLUE.

[@MakeItorBreakItNow]

Dano1947, thanks for the compliment, I think...

[@System32F]

Neobinium.... Replayed to confirm what I've heard burst out laughing, You made me cringe a bit the way you are holding that magnet haha you have a stanley blade too close for comfort also, I would watch Brainiac75 for learning how to handle strong magnets and his videos are amazing in quality, educational and for the entertainment, Some things made from iron will not be attracted to a magnet like if the metal has been cold worked it can lose its magnetic properties that's why the screw and eye is weakly attracted, great example would be most stainless steel forks parts of it will be weakly attracted

[@MakeItorBreakItNow]

System32, glad I could brighten your day with a chuckle, in follow on videos I try to say it right. Good points all around. Thanks.

[@amyfleming236]

the rope hole tie and bolt sent supposed to be hard to remove from it lol I make this

[@MakeItorBreakItNow]

Amy, thanks for the feedback. Agree.

[@amyfleming236]

+Make It or Break It lol its her son miles lol sorry I didn't see I was longed in on hers

[@amyfleming236]

+Make It or Break It this things are very very easy to brake boons with I have one that's 750 lb and I almost lost my toes

[@MakeItorBreakItNow]

Amy Fleming, agree that's not my hand, but nearly was on several occasions. What are you using a 75- lb force magnet for? Where did you get one?

[@amyfleming236]

+Make It or Break It I miles Fleming make them so I bought it home

[@rfi-cryptolab4251]

Why is it dangerous? If it sticks to the metal plate in your head??

[@gabrielsrandomness4171]

Make sure you don't put that magnet in sand or else the iron fillings will stick to it

[@williamwaters4506]

I bought a no name brand 400 lb fishing magnet. There is no way to test these magnets actual pulling power. I do not think that mine has anywhere near a 400 lb lift power but I did not pay much for it.

[@MakeItorBreakItNow]

William, Yeah they're hard to test, you really need to clamp a 1 inch thick steel plate to something that won't rip out of the ceiling in case the magnet is over say 200 lbs.

[@MakeItorBreakItNow]

Here's how I tested this magnet, but would do a lot of things differently next time: kzbin.info/www/bejne/rYnQlIqka7uHaas

[@subvet657]

pays for 350 pound magnet, won't pop for a #4 phillips to assemble it. priceless.

[@j0hn3b0yy5]

Ok, this dude should have a warning label for his own life

[@miguelmedina1991]

you got to get the aluminum magnet

[@MakeItorBreakItNow]

Miguel, thanks for the feedback.