Dillon XL750 9mm Casefeeder Issue Fixed? - Update

[@loops4860]

So glad I watched the follow up video. I had just purchased a case feeder for loading 9mm when I saw the first video and thought I made a huge mistake😅

[@ThecrazyScotsman]

Always learning always progressing and always helping each other in the process that is what we do!

[@utahmike3855]

Hello and greetings from Kanab Utah. I am about to purchase the XL-750 with a case feeder. Your problem allowed everyone to understand how the design of the sorting plate orients the cases in their upright and necessary position. Because the plate was elevated just enough due to the spacer being installed, it would not allow the case to fall out of the sorting plate as it proceeds up at an angle when rotating. The height of the sorting plate is critical to this function because it relies on gravity. The heavy bottom end of the case will not stay in the sorting hole/slot if it is bottom up and rotating upward at an angle. I found this entire problem/issue to be relevant because it explains the design of the sorting mechanism well. Thank you for all your efforts. Respectfully, Utah Mike.

[@chicowize]

Great tips Squatch, before I started buying parts to upgrade my 650 I did the same thing with a 556/223 case to stop case feeding. Hope the family is well. Thanks for sharing Brother

[@SquatchReloaded]

We are all doing well brother. Thanks for stopping by.

[@jh5869]

Good work, Brother. If you ever give up, you’ll never know how close ya were to getting it fixed! Thanks Squatch!

[@SquatchReloaded]

Thanks Jamie

[@apriliamille1234]

I kept having the Pink Floyd song money going in my head as you were cycling. The brass tinkling reminds me of the cash register in the song. At the 11:30 mark

[@craigwestwood8615]

You’re not the only dummy. I was having the same problem. My washer was in too. Thanks for the video.

[@jhs7947]

A wise person admits mistakes, good for you and good content.

[@malzdak6077]

Awesome content, I am just getting into progressive press reloading and your videos are very helpful.

[@TinManReloading]

Dude, I wish I would have seen the video where you were having issues. That's the first thing that popped I to my head! Sorry I missed that one buddy. Nice work getting her figured out!

[@SquatchReloaded]

I cant believe I never looked at the back of the plate after using that particular one for about 3 years.

[@RealEstateFireman]

Awesome troubleshooting and note-taking. Not to mention a great update to your xl750 review it rounds it out nicely. I was ordering my xl 750 this morning and all the Dillon case feeder pistol plates are out of stock :-( Thanks again for the update video.

[@SquatchReloaded]

Check armslist I have bought quite a bit of reloading stuff used on that site.

[@guardwelldefensellc1215]

Demonstrates the value of keeping notes. Thanks

[@Bondo1970]

glad you figured it out

[@kevinbeaupre8925]

Thanks ill have to check my shell plate on my 650 its feeding backwards on 7.62 But i did notice at around 11:20 looks like a something or a primer fell into one of the cases which could mess up the sizing/deprime or if thats already been done an didn’t catch it in the powder station you have it in with the powder an mabe cause a squib

[@fern6468]

Thanks for this video. I just picked up a case feeder with small pistol plate. Gives me the right direction to make sure I set it up right. It has to go under the tree for now though Merry Christmas and thanks again

[@rogermontee8264]

Glad to see it was a simple fix.Thanks for sharing Squatch. God bless☺️☺️☺️

[@tonygslc801]

Great Information Squatch, Thanks for Sharing 👍 Enjoy your Weekend and Independence Day 👊😎🇺🇸

[@SquatchReloaded]

You enjoy to brother.

[@ecarlo03]

I love all of your videos. Thanks for sharing so much information brother!

[@hughtanner208]

thank you for doing this and sharing the learning process.

[@c.patricksadowski9959]

Question: I just got a replacement case feeder from Dillon, my old one used the square white insert when reloading 9mm. Dillon send me a black funnel which they say I need for 9mm, but I notice that you are not using it, and have no issue with 9mm cases. Have you ever run it (the black funnel) in your machine?

[@fredericramsey3688]

Very interesting. Thanks for sharing..

[@gatesjuniorreloading3470]

Lol. We all have things like this happen. Good video brother.

[@dantow359]

your a god send. great info. im just getting my dillon xl750 set up. Thanks man

[@joejeans7913]

AWESOME BRO! something so simple!

[@karlasmus381]

I could not get 300 blackout cases to feed with the small rifle case feed plate I had been using for the 223s I was loading. It was my first change over with the small rifle feed plate. It would feed, almost half the cases backwards. When I installed the small pistol case feed plate with the spacer washer it fed the 300 blackout 100% but slowly. Hope this helps the next guy trying this!

[@SquatchReloaded]

I use the small rifle plate and adjust the slide at the top of the casefeeder and it works flawless.

[@karlasmus381]

​@@SquatchReloaded Dillon recommends using the large pistol plate with two washers added on the bottom but you have to buy screws for it because the original screws are not long enough with two washers.There are no adjustments on the 1050 case feeder that I’m using so I have to use the small plate and a washer because my large plate is used on another 1050 I leave set up for 45 auto talk to you later.

[@gruntspy44]

Squach can you adjust the primer seater on the factory t7 press?

[@SquatchReloaded]

Yes you can. Small adjustment screw at the base of the cup.

[@chrisgilbert2152]

Gotta love those fixes when you smack your forehead with your palm!!

[@scottbradley77]

Just curious, have you thought about adding a bullet feeder as well?

[@SquatchReloaded]

I run so many calibers I don’t think I would do it on my 750. If I ever get to the point where I would need a bullet feeder I would probably look into an automated set up

[@joedemelo5153]

I thought the washer is for long cases only. Did you install it for 9mm also?

[@SquatchReloaded]

It is I forgot I had it installed.

[@edwardasmus2600]

The problem I'm having is that the 300 blackout cases are feeding upside down way too much. It appears the slot in the case feeder plate it too long for the 300 blackout. It works just fine with 223 so it must be the 300 does not like the extra length of the slot.

[@SquatchReloaded]

If you adjust the deflector at the top of the casefeeder the 300 feed just fine

[@Tampaxd45]

Just pull the spring off of the bottom of the primer slide bar to temporarily disable it.

[@SquatchReloaded]

That’s another way

[@stephenswindle3839]

Even a squatch needs a refresh from time to time!!😁😅😂🤣🤙

[@jwedgest67]

So DO NOT use the spacer washer with the casefeeder when loading 9mm cases is what you are saying? I just bought a Casefeeder.

[@SquatchReloaded]

That’s right DO NOT use it. It is for long cartridges like 30 carbine

[@jwedgest67]

@@SquatchReloaded got it, Thanks because I probably would have put it in place!! You just saved me a headache!! lol

[@johnnyingram938]

Great video

[@robertvan2531]

I don't get bad feeds, but it jams alot

[@mithrandir1313]

The washer is for Rim'd cases.

[@SquatchReloaded]

Exactly

[@tittiger]

I blame this issue on Dillon. They do a very poor job IMHO of educating the owners of their presses.

[@SquatchReloaded]

That’s pretty much why I do what so do. I have probably reloaded more rounds on a Dillon press then Dillon. Lol