DIY 6 Channels Radio Control For Models. How To Make İt

How to make 6 channels radio control. Diy arduino radio control for Rc models. Diy arduino rc receiver and transmitter.
Necessary materials:
2 x Arduino Nano
1 x NRF24L01 + PA Wireless Module
1 x NRF24L01 Wireless Module
2 x Arduino joystick
2 x 100uF Capacitor (16V or above)
1 x 13 * 6 cm PCB Board
1 x 5 * 3.5 cm PCB Board
Arduino Nano: www.banggood.c...
Arduino Nano & USB Cable: www.banggood.c...
RC Joysticks (No trim): bit.ly/3vIMd4l
NRF24L01 + PA Wireless Modul: www.banggood.c...
PCB Boards:
www.banggood.c...
www.banggood.c...
100uF Capacitor: www.banggood.c...
Headers:
www.banggood.c...
www.banggood.c...
680R Resistor: www.banggood.c...
5mm LED: www.banggood.c...
Rocker Switch : www.banggood.c...
5mm kraft foam board (50x70 plate): amzn.to/2oE2vOK
JST Connector: www.banggood.c...
Mini electrical cutting plier: www.banggood.c...
Arduino IDE Installation, Adding Library and Uploading Code : • Arduino IDE Installati...
Thanks for watching. If you want to support my channel, join.
/ @kendin-yap
CODE & SCHEMES: www.rcpano.net...
OR tinyurl.com/47...
Arduino IDE, library file setup and upload tutorial : • Arduino IDE Installati...
My Web Site (KendinYap): www.rcpano.net
All of my videos: bit.ly/2Z9QVYK
Thanks For Watching And Please don't Forget To Like, Share & Subscribe For More Awesome Videos.
KendinYap Channel / @kendin-yap

[@francisaaronabadingo3902]

thank you again sir, for sharing this project.. I have tried it and very satisfied with the result.. I'm trying to add a battery monitor on the RX side back to TX -- but I'm still working on it, having a hard time on the codes.. I'll share with you the codes as soon it works.. wish me luck..

[@dontknow479]

I have li ion battery instead of lipo will that enough for transmitter and receiver! Please reply!

[@davydbar]

@@dontknow479 yes

[@shaunferris6063]

hello when you built this did you only use the 3 libraries he added or did you have to add anything else?

[@RohitKumar-wl5fw]

Bro tell me that it work or not

[@Shrey-j4l]

Take help of chat gpt for codes

[@PunakiviAddikti]

Basically with this setup, you're only limited by the number of input/output/analog pins on your arduino. You can send any data. It's a digital radio control system. Want 15 channels? You'll need 15 input pins and 15 output pins. But be aware that some joysticks use hall effect sensors. Those work differently than potentiometer based joysticks.

[@krulikonik]

You cannot use 15 channels fully, cause you need analog pins for joysticks.

[@Gifted_Gift]

please how can i make 15 channels?

[@PunakiviAddikti]

@@Gifted_Gift You'll need a microcontroller board with enough IO pins

[@AKElectroDIY]

Very simple, use an arduino mega board. It has 16 analog pins

[@JarppaGuru]

can it handle 15 channels or even 1024. if you need buttons use parallers serial chips LOL for remote 74LS165 (paraller in/serial out)you can use multiple input using ehh 3 wires? for vehicle 74LS164 (serial in/paraller out)(74ls595) turn then back output pins on ardnuino not any limit you can expand input and outputs but can this wireless thing handle more than 15. dont know LOL@@Gifted_Gift

[@nicolasmarti6725]

this is awesome ! much respect from a french guy living in japan, sir

[@thanhnamnguyen8888]

Can you give me code of arduino nano, please

[@Er_Maneendra_Singh]

Thanks a lot Sir ji, I’ve also made a Transmitter by using your circuit and code. And It’s working 🙏🏻

[@KILLERgGaming-nt4eg]

Bro will you help me please

[@Dragon69FlyTeam]

This is a great idea for my old broken robbe transmitter. eprom get wiped now i can use it again thanks

[@barskaan4014]

senin gibi kanallara ihtiyacımız var umarım hak ettiğin yerlere gelirsin

[@VENOMR9]

bu vidonun önce 2 vidyo işime yarar

[@vilsonandrade8191]

Very nice explanation. Even though as mechanical engineer, I could understand well. Congratulations from Brazil - Parana state - Araucaria city

[@anonymousbay7957]

bro it can not connect VCC pins thand how the every thing is working properly

[@MasboyRC]

This is so cool !! Really nice idea. Greetings from indonesia 🇮🇩

[@aanandian8925]

sama wek

[@ahmetoguzhan7122]

Şuan bu işin maliyeti 377 TL tuttuyala😲 bu paraya 6 kanallı uzun menzilli bir kumandaya sahip oluyorsunuz! Bu devirde imkansız gibi bişi😕 her ne olursa olsun bu kanalın ve bu adamın emeği yenmez! Bu kalitede ki bir videoyu hazırladığı için ne kadar teşekkür etsek azdır😉

[@MEKATRONA]

Çalıştı mı

[@ahmetoguzhan7122]

@@MEKATRONA evet ama ben artı olarak şarj etmesi için TP4056 Type-c 1S 3.7V Lipo/ lityum pil şarj devreside eklemiştim ,

[@nocomment_uzb]

Juda ajoyib. O‘zbekistondan salomlar.

[@HasanAraycProjects]

Üstadım uzun bi zamandır yoktun emeğine sağlık söylemeye gerek yok yine muhteşem bi Video

[@GustavoLima-jw1vo]

Meu amigo aqui e do Brasil, sou fan dos seus videos, parabéns pelo ótimo canal, ficou muito feliz que você sempre compartilhe com a comunidade os seus tutoriais que são um máximo 😎

[@Kendin-Yap]

Thank you.

[@calibermix8159]

@@Kendin-Yap what gimbals are you using ? the crap gimbals of the banggood link look totally different

[@huseyincan5495]

@@Kendin-Yap videodaki joystickleri bulamadım onlar yerine ne kullanmamızı önerirsiniz

[@warismwarism4300]

@@Kendin-Yap hey thx for this great video its realy informative , so can you plz explaine how we can use 433Mhz Module RF Émetteur + Récepteur

[@islamlechelah2793]

@@Kendin-Yap hey is there is any diff if I use RC Joysticks with 5k resistor? like this : www.aliexpress.com/item/1005001616807525.html?spm=a2g0o.detail.1000014.1.133f3ae4JBVZy0&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40000.326746.0&scm_id=1007.40000.326746.0&scm-url=1007.40000.326746.0&pvid=f9d48c80-abac-4aef-9a42-631366ed2d8a&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40000.326746.0,pvid:f9d48c80-abac-4aef-9a42-631366ed2d8a,tpp_buckets:668%232846%238114%23762&pdp_ext_f=%7B%22sku_id%22%3A%2212000018004611774%22%2C%22sceneId%22%3A%2230050%22%7D&pdp_npi=3%40dis%21EUR%2111.42%2111.42%21%21%21%21%21%402101d1b216776937474897001ed7a3%2112000018004611774%21rec%21DZ%21

[@debashishdas4865]

Awesome bro.l was finding this type of video for very long time ago.Keep it up and you will get more students and subscriber

[@TheSayargyi]

I'm very poor in this technology, I've followed all steps and builded a receiver but I'm stuck to upload receiver codes. May I respectfully request you to guide me the basic way to upload the codes, please!

[@baddreams0919]

Now I know what i'm doing this summer vacations

[@xxxtrib]

did you do it?

[@peterbogner1675]

Dear Kendin Yap, i like your videos very much. The best thing ist, that i can learn now, on my old days good electronic stuff that is totally new for me. But your videos are good and your website make the rest ... i will hope so ...... :) .... to build my own controller and other stuff. Thank you very much for your work ! Greets from germany, Peter

[@JoaoNelsonLima]

The next version, print the case on 3D Print. =)

[@SummerBR]

Good Idea even though the way he made it is good. Makes it original

[@tahayasin0004]

Menzil'i kaç metre ? How many meters is its range?

[@agussp6731]

@@tahayasin0004 about 120 meters

[@suchandrapaul5047]

Marvelous creation ! Very good job.

[@Kendin-Yap]

Flight Test video … kzbin.info/www/bejne/rZaUmmiMiahgb8U

[@gultekineroglu3070]

hocam yeni baslayacaklar icin bu malzemeleri nerden buluruz onu da açıklamalara ekleseydiniz keske

[@bird9]

very good video ! But Can you make an RC controller with just elementary electronic components like transistors, self, capacitors.... Without using components like NRF24l01 or arduino or or...... Please ANSWERRRRRR I am so and so interested by this 💪💪🤗

[@debashishdas4865]

We are eagerly waiting for your upcoming video

[@samerbenmbarek7348]

Bravo good job ❤

[@peace4128]

balık yemleme botu bait boat yaparmısınız?

[@artmartdc]

I really enjoyed that and it has given me an incentive to make it!

[@nightsaber2272]

I've make rc control almost 20 yrs ago. Even joysticks was handmade :)

[@icanseeyourfuture8674]

How did u get the circiut board?Did u sauder everything yrself??

[@nightsaber2272]

@@icanseeyourfuture8674 Made it myself drawing all by hand. :)

[@icanseeyourfuture8674]

@@nightsaber2272 wow nice🤝🏾.So someone like me who wants to build something cool,what course do u think i should do?Whatd the easiest path to learn to build controls from scratch?

[@nightsaber2272]

@@icanseeyourfuture8674 Best and cheapiest way is to buy)

[@vdm7776]

Meraba! Many thanks for your video and projects. Just, like a new idea, can you add a LCD screen for back feed with the model, such as a battery voltage and signal strength. And the selection of the model, if you will use two similar transmitters for several models at the same time?

[@ekojokosetyono5823]

thank you so much, Bro. it's very good for me to learn arduino.

[@GAMEmaster-ir8ge]

I need help

[@jithashaju4331]

​@@GAMEmaster-ir8ge😮

[@vitorbonis2632]

Parabéns ! Obrigado.... pelo vídeo e por descrever as peças de montagem.... Saudações do Brasil.....

[@shamalapawar4015]

Thanks for the video. Very good for something to make in Christmas

[@Satishtechni]

I like your tutorials and see attention thank you very much..

Üstad ellerine sağlık. Gerçekten güzel bir çalışma olmuş. Bir sonraki menzil testi videosunu merakla bekliyoruz. İmkanınız varsa bu sisteme birde fpv ekleseniz süper olur :))

[@sivambhai1971]

Shivam

[@eduardo33]

Maravilhoso o seu vídeo! Isso deveria ser um curso em escolas o que as crianças aprenderiam seria de imenso valor! Saudações do Brasil mais uma vez.

[@mcreativeworks9931]

VERY NICE AND I AM ALSO WORKING OF MAKING ON EOF THIS

[@suleymandogan8205]

kendi milletimden bu kadar uğraşıp ticari amaç gütmemeniz beni şaşırttı. genelde bizim toplum iyi bişeyi bedavaya kolay kolay yapmaz. umarım hal ettiğiniz yere gelirsiniz.Tekrardan elinize emeğinize sağlık

[@RcModwerks23]

Awesome video! I like cool DIY videos like this ! Keep it up 👍

[@moathnaji2763]

Salam friend I like all your tutorials and your channel one of my favorites… Could you make step up USB cable dc-dc booster 5v to 12v with 1 amp or more. Please?

[@ManusWorkbench]

Awesome video brother , i have a doubt could use this transmitter and receiver for quadcopter . If yes could you explain that for me. It will be good if you post another video about this 😊👍

[@vilho4649]

I would not use it with a quad

[@animeepisodes6724]

Maynn, where do you keep all this talent?!?

[@topglobal6kagura27]

In your mom closet JK XD

[@tomjoad1060]

Very nice work, Kendin Yap!

[@vaampa_gaming69]

Nice vdo bro...I like ... I wanna try to make an rc car ..with this remote .....❤️

[@beratbaki1681]

Artık bu alıcı ile bir dron toplarsınız.

[@michelemarchese259]

Fantastic! Beautiful work!

[@peytonsmith8765]

Can you pls send me a link to the joysticks with trim? Great vid btw

[@8.2deck]

They're in the description

[@peytonsmith8765]

@@8.2deck those don’t have trim but I found some that do

[@Matt-rq5yn]

@@peytonsmith8765 hey, i have been looking everywhere for joysticks with trim, where did you find them?

[@basrikaragulle2933]

Kanalınızın hep bu kalitede devam etmesi dileği ile... tebrikler

[@sumonmondal5041]

Your every video is helpfull.Thanks.Go on.

[@BakshishSingh-rc6ki]

What is the total range of transmitter and reciever?

[@John-hg3mo]

he spoke in the commentary that he will test in the next video.

[@keenanjensen5552]

according to the website, 1100 meters

[@AshishKumar-bz4qs]

Ye items kaha se milenge bhai kon bechta he

[@AshishKumar-bz4qs]

@@keenanjensen5552 z

[@tahacevherunal2690]

1100 meters

[@ryansmithza]

I found my old Walkera WK-2402 yesterday, it will be my new Arduino transmitter! 🎊🎉

[@moviecinema7262]

Thank you so much for the code! It worked without any delays

[@JavierCastro-om3tk]

Muy bueno quedo 👍👍👍👍👍 Un saludo desde Argentina

[@TinC33]

Great stuff, can't wait to get enough free time to make one for my traxxas summit and hidraulic snow plow controll.

[@kisacaek]

Hocam sayende atölyeme birçok ekipman katkısı yaptım.Kağıt öğütücü / doğrayıcı yapabilirmisiniz. Malum bazı resmi evraklar oluyor imha edecek yer veya durumumuz olmuyor.

[@profezor2]

2 tane kaz yavrusu al, kagıtları altina ser, paramparça ediyorlar 🤣😅

[@imagineperest9958]

Abi bununla da bir uçak uçursana bakalim menzili ne kadar olucak hazir onceden yaptigina entekre edebilirsen etmeye çalışırsın

[@profezor2]

Menzilinin çok iyi olduğunu düşünmüyorum.

[@sakofar3506]

I have some questions for this work

[@purneshchandrayadav8419]

Amazing work. Really loved it ❤❤👌

[@hafsathkk8236]

How many meters are range in this remote control

[@devashreenasare950]

120

[@patrickczader3995]

You could map it to whatever range you want. Like if u wanted precise control u could do 0-50 but if u want the full range just do 0-180

[@Crystalservices]

3 misguiding comments 😂

[@dahamdhibihansa9843]

What's the library

[@indunilprabhath1484]

great video, how to controlled drone using this transmitter and receiver, please make tutorial , thanks

[@antonisvianos8017]

Perfect Job and works very good.!!!!!!!!!

[@mezat8745]

Abi senin projelerin bize çok yardımcı oldu Seni bulursam elinden öpücem

[@MythHoor]

3d Yazıcı kullanarak yapmalısınız artık. Her vakit karton olmaz yani

[@berkaypolat6621]

İnsanlar da yapabilsin diye uğraşıyor bence. Ve bunu 3d yazıcı ile yapsa kanalın amacının bir anlamı olmaz çünkü her evde 3d yazıcı yok

[@MythHoor]

@@berkaypolat6621 Her evde joistik ve RC alıcılarda yok. Haklısınız ama evde yapılabileceğini söylese How to Home a make olarak başlık atar.Söylemek istediğim daha kaliteli bir video da ortaya çıkmış olur.

[@sakofar3506]

Thanks for this video. Can I know your name on the Facebook page in order to speak privately, please

[@suleymandogan8205]

elinize emeginize sağlık . çok güzel görünüyor

[@serdaraga3997]

vay be zamanında sana sordum abi arduino ile uzaktan kumanda olurmu diye rc uçak için olmaz dedin şimdi sen yaptın ;D helal

[@Kendin-Yap]

Olmaz dememişimdir. Normal bir kumanda gibi verimli olmaz demişimdir. Ve bu doğru.

[@serdaraga3997]

@@Kendin-Yap o zaman pardon :) iyi günler

[@motivational67624]

Very Nice.. In Bangladesh 🎉

[@pinobarberio6193]

Hi, I just made the remote control that works very well, except that the joy on the left is not at zero, but with the kk2 and not only, it oscillates between 9/10 values. I saw in the video that your radio control has in trims ... but I couldn't find them ... putting these could solve the problem of these variable values. Thanks for your reply and always great compliments for your accomplishments of which some have successfully succeeded me ... a greeting

[@elbecer]

kardesim , emegine saglik. Ayni seklinde DEVam!

[@erhanmutlu6443]

o kadar haklısın ki kanalı yabancı hale getirmekte. videoların hepsi ayrı ayrı çok güzel ellerine sağlık

[@prov_s195]

For who want, i got the sticks from old joystick of playstation, works perfectly

[@abhishekch.7125]

That's a really very nice 6 channel transmitter and receiver, but I want to know one thing which is- What will happen if the battery from the receiver side gets discharge? Will the receiver alert in that situation or not or, will the RC plane, drone etc in which ever we use the receiver of this transmitter gets fall down accidently? Because in such case the market receivers like flysky FS-CT6B alerts as its receiver starts to run and then off the motor in whichever RC plane it's installed, and one more thing can we run this DIY transmitter and receiver using 12v current? Please reply I am curious and want to know about that. By the way nice video 👍👍👍👍

[@pratyakshaggarwal5737]

U have to modify receiver code if u dont want the motors to shut down. Currently this receiver will shut down motors as soon as battery discharge

[@bugracanbagrack3470]

hocam ellerine sağlık mükemmel olmuş :D

[@Inventor_lk]

Can we use Arduino nano and uno

[@huseyinakcit1165]

Usta senin kanalı yeni keşfettim, çok şey kaçırmışım, başarıların devamını dilerim....👍🏼👍🏼👍🏼

[@premkumarms1772]

Mannn that is awesome and im following your video to make my own. Ill really appreciate if you could add an oled display to it really liked it maann

[@hansadhinga2234]

which material I can use instead of foam cardboard

[@nikbivation]

this helps a lot, thank you!

[@uditgamezofficial]

Thank you for the helping😊😊😊😊😊😊😊❤❤❤❤❤❤❤❤❤❤

[@Playersdodigital]

Harikaydı, ama model uçaklarınkine benzer bir karışım yaparsanız, bu joystick'i sağa entegre ederseniz daha iyi olur, böylece yukarı doğru hareket ettirdiğinizde iki servo yukarı gider ve aşağı doğru hareket ettirdiğinizde, iki servo aşağı doğru hareket eder, yukarı doğru hareket ettiğinizde. sol taraf yukarı, diğeri aşağı, sağa doğru hareket ettiğinizde yukarı ve diğeri aşağı iniyor.

[@Kendin-Yap]

Teşekkürler ama bir yanlışınız var. Bu kontroller MODE 2 standarttıdır. Avrupa ve ülkemizde bu standart kullanılır. Bu kontroller tipik ticari üretilmiş bir kumanda ile aynıdır. Bu kumanda ile uçurduğum uçağın videosu da ilginizi çekebilir. kzbin.info/www/bejne/rZaUmmiMiahgb8U Sol kol Gaz ve Rudder. Sağ kol ise Elevator ve Aileron dur. Ailerona (Ana kanat kontrolleri) ne bağlı olan servolar ters hareket etmek zorundadır ki aileron olarak görevini yerine getirebilsin. Eğer Elevatörü kastediyorsanız. Elevatör zaten sağ taraftadır ve olması gerektiği gibi hareket eder. Kanalım için yaptığım ve yüklediğim videolar sadece kanalım için ürettiğim içeriklerdir. Ben uzun yılladır yakıtlı ve elektrikli model uçak ve helikopterler ile hem hobi hem de profesyonel anlamda uğraşan bir kişiyim. Diğer videolarımda ticari üretim olan çeşitli kumandaları da kullandığımı görebilirsiniz.

[@lezbriddon]

i do wonder what range can be expected from low price modules

[@AnttiMaeki]

Nice job. That looks very much like 1970s radio controllers. They had a metal frame though but it was usually coated with pale brown paint. I wonder where could you find those control stick modules?

[@movingears5582]

Hello! Have you tried programming the BK2461 (FLIP51) radio module chip itself? According to the datasheet, it has 4 ports for PWM control, which is very interesting. But I can't find documentation anywhere on how to program it.

[@AKElectroDIY]

I made this transmitter and receiver. I used the same joysticks that you provided link in description. But I'm facing a problem. The transmission system itself is working just fine. But I think there is a problem in joysticks calibration. I did some changes by checking the values of joysticks and doing amendments in the code, but there is still some problem. The first 5 channels having potentiometers are constantly getting small amount of fluctuations in their values. The channel 6 having a two position switch is working just fine. Also, when I finally did the joystick calibration by mapping the approximately correct values of joysticks, there are still a lot of fluctuations in the servos when I move the joysticks. By fluctuations I mean that the servos are not moving smooth when I move the joystick. They are like moving with rapid vibrations. Can you help me fix that?

[@Kendin-Yap]

I made this circuit 4 years ago. I don't remember having this type of problem. But using the analog pin instead of digital for the 6th channel may have caused instability. You can try a solution like this. TRANSMITTER CODE: data.aux2 = mapJoystickValues( analogRead(A7), 12, 524, 1020, true ); Replace the existing line above with the line of code below. data.aux2 = digitalRead(3); And solder the pin connection of the switch to D3 instead of A7. RECEIVER CODE: ch_width_6 = map(data.aux2, 0, 255, 1000, 2000); Replace the existing line above with the line of code below. ch_width_6 = map(data.aux2, 0, 1, 1000, 2000); If the problem is still not resolved, you may have a hardware problem. Like a broken potentiometer... NOTE: Also important are the batteries you use for the transmitter and receiver. A low C value (current strength) causes problems such as unstable operation, slow and intermittent movements).

[@AKElectroDIY]

@@Kendin-Yap Thanks for the help. Will surely try it. Also, I made the 4 channel arduino based transmitter using arduino joysticks and that's working very good. The same you made. So as you're saying this might be the real problem. Also I twisted the ground wire around MISO and MOSI pins, like you showed in your 8 channel transmitter. And the whole setup of transmitter contains a lot of wires like a mesh. Can this be also the cause of interference?

[@AKElectroDIY]

@@Kendin-Yap Tried this step of completely removing the aux2 switch from hardware and software. Problem is still unsolved. Any other idea?

[@samiabbasi4278]

Good morning, all your project s are very nice, I have a question : what is The most radio transmitter in the 2 this models : FLY-SKY OR FUTABA T8J ?

[@ralphmadera4366]

This is a nice 👍 project, I hate cardboard and hot 🥵 glue though.

[@amisidmon3209]

that is foam board not cardboard

[@bernardoraddatz9704]

Excuse me sir, but if use you own DIY esc, like that you made, can I use the 5V from arduino to feed the servos?

[@Kendin-Yap]

Arduino does not provide enough current strength. You can use an external regulator.

[@bernardoraddatz9704]

@@Kendin-Yap hello, thank you for the nice project and tip, one more question can I use the battery feedind DIY ESC, to feed the servos, the DIY ESC can feed the arduino?

[@3407윤영진]

fabulous work!! But how does it work without connecting 5v to the Servos?

[@Kendin-Yap]

Thanks. The servos are fed from the Bec circuit of the ESC.

[@dipanshudhote5671]

thanks man ur code really help me..............

[@dipanshudhote5671]

@sunnyshinde515 kya problem aa rhi

[@dipanshudhote5671]

@sunnyshinde515 msg me on insta @_di_pa_ns_hu_

[@vineethk5276]

ARE YOU USING POWER FOR THE SERVOS FORM THE ESC ? OR DIRECTLY FROM THE BATTERY

[@Kendin-Yap]

The servos are fed from the BEC output of the ESC. But if desired, servos can be fed with an external battery (5-6V)

[@vineethk5276]

@@Kendin-Yap OH OK....Thanks for helping out man.... appreciate it 👍

[@pajohnbuilds]

Excuse me sir, if i want to use it in rc car, i must change data.throttle = 12 to 127 right? So i can move the motor to forward and reverse ?

[@Kendin-Yap]

yes

[@pajohnbuilds]

@@Kendin-Yap thanks you for your response sir, but I have one question,, if i want to use brushed motor for all channel (so i want to change all servo with motor), i must use esc in every motor like your video rc drone using this controller?

[@Kendin-Yap]

@@pajohnbuilds Yes, motors cannot be directly connected to the receiver. One ESC must be used for each motor.

[@pajohnbuilds]

@@Kendin-Yap tkanks you sir....

[@Mahommadharis]

Bhai kya ise pc me program kar sakte hai??

[@AKElectroDIY]

Sir I have 5K joysticks. They are pretty much similar to these ones. Will they work fine?

[@AKElectroDIY]

The same joysticks I have as you have given link in description

[@AndresGonzalezMaker]

Great proyect and very well done video. Can I ask you where did you get these joysticks with the trim option?

[@Kendin-Yap]

Thank you. I bought the joysticks from a local dealer. A store of robotic materials and RC model supplies.

[@AndresGonzalezMaker]

@@Kendin-Yap Thanks for your answer, I will search them.

[@GurveerModelMaker]

Can i use my old transmitter?

[@gitra182channel]

Good job,,, 😇😇😇

[@haritkrishan947]

When you solder the male pin headers for the channels on the receiver, I see you connect the signal and ground cables to the respective pins on the Arduino, but you don't connect the middle row (the red power lines) to anything on the receiver. How are your servos getting power? Do you not need to connect the power lines to power the servos? Is the signal line sufficient to power the servos? For reference, @6:23.

[@Kendin-Yap]

The servos are powered by the ESC's Bec output.

[@haritkrishan947]

@@Kendin-Yap Aaaah of course! Ok that makes sense. So does that mean you are not powering the receiver with the BEC? To simplify, the BEC only powers the servos. The receiver is powered by dedicated power source (battery). BTW I really appreciate you reading and responding to my queries! I love your work!

[@manishgowda8641]

Awesome work really helpful

[@One_Ten_RC]

Will this set up work using single axis joysticks donated from older 2 channel transmitters?

[@Kendin-Yap]

It works with joysticks with analog potentiometers.

[@onur6290]

bu devreleri kurmadan önce bordun üzerine denemeler yapıyor musunuz ? entegrelerin sağlam olduğunu nasıl anlıyorsunuz?

[@Kendin-Yap]

Bazen breadboard üzerinde test ederim. Ama her zaman değil

[@onur6290]

@@Kendin-Yap nrf çalışıp çalışmadığını nasıl anlıyoruz

[@kamilsen]

Sorum şu; servo motorların takıldığı uçlara düz motor bağlarsak çalışır mı? Ya da tepkisi ne olur? Bizde yanlardan iki motoru olan, suda yüzen bir araç projesi var da. yönünü ve hızını bu motorların ileri ya da geri çalışması ile belirlemeyi düşünüyoruz. Yani yön için kuyruk kanadı vs. kullanmayacağız. Dolayısıyla bizde servo motor olmayacak. Düz dc motorlar olacak. Bu motorları hem hız kontrollü hem de ileri geri yönde çalıştırma işini bu kumanda ile yapabilir miyiz? Cevap verirseniz çok seviniriz.

[@Kendin-Yap]

Kumanda alıcısına direk olarak DC motor takılamaz. Arada ESC (Elektronic Speed Control) olması gerekir. Direk takarsanız kontrol edilemeyeceği gibi alıcının da bozulmasına sebep olabilirsiniz.

[@justhamba24434]

Luar biasa MANTAP...👍👍

[@samuddhaofficial4303]

Can we add more operators?? I mean joysticks and switches...

[@Kendin-Yap]

Yes it is possible. It is limited to the pwm and digital output pins of the Arduino board.

[@samuddhaofficial4303]

@@Kendin-Yap what is the maximum operator limit?? Plz reply.

[@Kendin-Yap]

@@samuddhaofficial4303 I think 8 for Arduino Nano

[@samuddhaofficial4303]

@@Kendin-Yap For arduino mega?

[@Kendin-Yap]

@@samuddhaofficial4303 Arduino Mega is a big module for this type of project. That's why I never used it. But it will provide much more channels than Nano.

[@ahmetizmir1081]

Güzel olmuş, elinize sağlık.

[@er.h.screations233]

Excellent work sir,I have question can a 3 channel rc system be converted into 6

[@AmbitiousAB1]

What's the total cost of making it? And what's the max range?

[@dilukagimshanmaduhansa6782]

Do we use 2 nrf24l01 +pa or

[@randomgeno6490]

Great job bro 👌 .. I only got a question In receiver why did u power the system with the direct 7.4 v ? And u could Of used the BEC in the ESC As if anyone wanted 11.1v or higher That would kill the Arduino I believe After all everything is awesome And I really like it .. Thanx for sharing

[@Kendin-Yap]

Thanks. Many versions of Arduinos support 7-12V input voltage. If you use the BEC voltage of the ESC it will work but you will have a lower value for the 3.3V output pin. This is not good for the NRF24 module. The control distance will be shorter.