DIY Cargo Trailer Door Window Installation

[@spaman5440]

At 13:45 the video started getting good ....You guys are funny. And 14:35 is the best...And then she comes in and screws it in ... Awesome video great job.

[@HolidayForTwo42]

Thanks 😅

[@Nightowl-OO]

After doing 2 cargo trailer conversions, and installing several windows. I’ll offer the following, before purchasing the windows, removed the interior wood and check spacing of any supports, or wiring. It may provide a consideration in window selection. At the very least you will know if you are cutting through supports. While the interior wood is removed, add insulation if not already installed.

[@seanwilson6521]

That's some real life action, lol. That's me all day long. It looks fine, well done and this is going to be helpful for me down the road.

[@HolidayForTwo42]

😊 you’re welcome and thanks!

[@TerryX2Explore]

I am so glad we are done with all that kind of work! ;-) Nice window... None of those jobs are ever as easy as they look. LOL Looks like you guys are doing pretty good! Can't wait to see what else you do with it! 💙Terry and Terri

[@AliAhmadi-hq9pj]

You did good job really appreciate sharing 🙏❤

[@Nathanallenpinard]

Mine had latches on it to hold the secure bar in about that location, so my guess is they put those in every model to allow that possibility. If you had that custom made with a latch, they probably just use the same frame.

[@matmichalke5734]

My windows from Amazon also did not have instructions but came with self tapping screws. I added a wood frame inside the door and wall to better support the windows

[@kpd3308]

The phillips screws might be JIS (Japanese Industrial Standard) which uses a slightly different (JIS) screwdriver geometry. Phillips screwdrivers tend to strip the heads of JIS screws.

[@Nathanallenpinard]

It would be nice to know what I have in mine because taking off the luan without breaking it requires taking off the WHOLE DOOR. Or, at the very least unbolting one door strut at a time. I see you got the RV latch. I kinda gave up on that and use the shed door knob instead.

[@4bearsi678]

The end results were good though. Is there predrilled holes on the outside window that match up to the inside trim pieces that has the predrilled holes? Looks like the screws would go into the into the window track and sit very close to the window pan. But that may be just how it looks in the video

[@HolidayForTwo42]

No predrilled holes anywhere, there is a metal band/ring that goes on the inside section of the window frame that you run the screws through into a band on the out side section of the window - that essentially pulls the two sections together tight and holds the window in. There were no directions included in my shipment - but once you start looking at the two pieces it starts to make sense. lol! but thanks, it did come out okay after a few rough moments - once you do one, the next will be so much easier.

[@scottpresley8264]

The reason the screws were striping is they are made for a square bit driver. There actually a much better option but you have to use the right tool.

[@HolidayForTwo42]

Yes I realized that later, oh well something’s you learn the hard way lol 😂

[@mitchhall5942]

You can also put duct tape on the shoe of your jig saw to keep it from scratching

[@HolidayForTwo42]

Great tip, thanks! 😊

[@MDCF1565]

Hello, and thank you for your time. Is there a frame in the door or crossbars of any kind, I'm about to pick up three 20x30 1.5 windows for my ctc and was wondering if there was any internal beams in the doors. Thanks again

[@HolidayForTwo42]

Not that I know of, I was caught by surprise with that door on my trailer and still not sure what purpose that bar served other than support for the door lock perhaps. There are beams in the walls, but be prepared for surprises- Good luck on your windows.

[@donniehare7654]

What kind of beds are those?

[@HolidayForTwo42]

Those are two Coleman sleep cots I got from Amazon, along with extra sleep pads (memory foam 😉) very comfortable too!

[@tmbrown2409]

Pull timber panel off back and stencil in area with no structural elements and also check for wiring should be step 1 everytime

[@bruceschneider6914]

Next time use a professional 😂

[@HolidayForTwo42]

@@bruceschneider6914 why would anyone want to do that? Nope, It was a learning experience, we actually had fun and now it’s in and it works great 😊 and we didn’t have to pay labor charges $$$… once you’ve done it on your own, second time will be easy!

[@eduardomachin6658]

Forget this hater! You did great 👍🏽

[@DigitalDoxology]

@@eduardomachin6658😂 it doesn’t bother me, but thanks for the encouragement lol 😆