Diy Class A Stereo HiFi Amplifier at home step by step in the end of the video a short test with jbl 4430.
Пікірлер: 40
@netfix3842 жыл бұрын
When applying your map in reality, I was fascinated by the loud and clear sound, and the shape was distinct and tidy. 👍👍👍👍👍👍👍👍👍👍💕
@homemade_audio2 жыл бұрын
Yes. It's. I had the same impression when i lessened to it.the sound was verry clear. Thanks very much to made my diy amp 😋. You can also replace the two resistors for each channel with just one 8ohm 10w that will improve more the sound. Good luck ✌
@b.caingletryan463517 күн бұрын
Bro i dont have cement resistor available in my home what is the best alternative? It is okay to use regular resistor with the same value?
@fasttrack56193 жыл бұрын
Hmmm very impressive 👍👍👍
@gertskjlstrup1804 Жыл бұрын
trafo 12v and how many amps? How big is the fuse? Nice work!
@Jac0b1094 ай бұрын
I have to say its very impressive plus i like the simplicity of the amp might try to make this one, also what would be the estimated wattage putput for both speaker outputs?
@jerryadams44492 жыл бұрын
Brilliant step by step including shipping or scavenging list too. Thank you,As a novice to electronics (I have assembled the digital clock kit and it worked first time😁) I feel confident in following your steps, would this amp be ok to use in a thodio type ammo can twin speaker box,can this amp be made with a wireless input and where would you best input the Bluetooth board signal leads?
@homemade_audio2 жыл бұрын
Thank you for your comment, yes you can add bluetooth audio board and connect it to line in as shown on video to make wireless speaker.
@VC27 Жыл бұрын
The simplicity of this project is enticing me to build it, however, I have very little knowledge of electronics. You will have to excuse me for my noob questions. What would be the RMS output per channel of this amplifier? In some of the components, you have mentioned 'audiophile grade'. Can I use non audiophile grade components of the same values? What can I use in place of the inductor coils? They are not available in my country. In place of the attenuator, can a potentiometer 10 kOhms 25 mW be used? Is it possible to connect potentiometers for controlling the bass, treble and balance, on this circuit? If so, how do I do ir? I have always wanted to build a Class A amplifier and this is probably the best chance that I will ever have. Much obliged for going through my entire post, any suggestions, instructions or advice will be appreciated. Thank you.
@SheikhN-bible-syndrome Жыл бұрын
I made a class a 2 npn amp alot like rhis and i can get 8.5w rms out of it with a 18v 60w power brick and 2 100000uf caps
@bybeetho2 жыл бұрын
*Parabéns e agradecido por essa informação bem orientada. Vou fazer um exemplar desse e testá-lo aqui em Belo Horizonte (MG) Brasil. ... Beetho, da "Boomerang Flowers Band ®". ... ... Congratulations and thanks for this well targeted information. I will make a copy of this and test it here in Belo Horizonte (MG) Brazil. ... Beetho of the "Boomerang Flowers Band ®".*
@carlosteixeira9106 Жыл бұрын
Terra do Milton, Borges, Venturine, Beto, Tiso e Toninho. Só fera nessa terra!
@napatencie44212 жыл бұрын
What for are theese little coils at the output? 🤔 Classic Common Emitter. This amplifier inverts the phase 180 degrees and therefore the speaker plus should be connected to the ground of the amplifier. Why is the output capacitor connected between the resistors instead of directly to the collector?
@homemade_audio2 жыл бұрын
whatever the phase rotation has no impact on the sound of the speakers in normal wiring. the phase rotation of an amp is taken into consideration in the case of active biwiring where there are several amps with different phase rotations, in this case we do the phase correction by digital active filter and that's it is normal because even major amp manufacturers announce the phase rotation of their amps.
@homemade_audio2 жыл бұрын
since the phase rotation of an amp is the same on both speaker outputs it has no impact on the sound because the two speakers remain synchronous.
@domenicodangelo78402 жыл бұрын
Bel video! Mi piacerebbe provare a realizzare il tuo progetto, quali caratteristiche deve avere l'alimentatore da 12v? Al posto dell'attenuatore è possibile utilizzare un potenziometro logaritmico stereo da 10K?
@homemade_audio2 жыл бұрын
Potenziometro 10k ok, per l'alimentatore 12v basteranno 2A per le prove, preferibilmente basato su un trasformatore migliore di quelli con commutazione.
@omidsaegh849 Жыл бұрын
Hello, can you tell me how many watts? Can you please make it with four negative transistors irfp250 and class A, and the circuit please be mono
@napatencie4421 Жыл бұрын
When the output is by the capacitor, what for are these little coils?
@homemade_audio Жыл бұрын
it is to reduce high frequencies beyond 20 khz.
@m.r.m.milhanmilhan85973 жыл бұрын
Good idea bro
@homemade_audio3 жыл бұрын
thanks much
@c.240 Жыл бұрын
Genial !! Donc cet ampli est alimenter en 12 volts ? Est-il possible de faire le même avec une alimentation 220 volts ? Et que pourrait on ajouter pour lui donné plus de puissance ? Super boulot 👍
@homemade_audio Жыл бұрын
Avec 220v AC le montage va exploser 💣💣💣 ATTENTION il ne faut pas jouer avec de l'électricité ⛔️⛔️⛔️
@jai_nTr_92 жыл бұрын
Hi sound engineer👌👌👌
@user-nk5ye8vv6k Жыл бұрын
Отлично!
@homemade_audio Жыл бұрын
Большое спасибо 🙏🙏🙏
@marointn84482 жыл бұрын
Please Diagramme Loudness on Amplificateur
@enzodesiderato15852 жыл бұрын
grazie sei molto chiaro bel video, avrei una domanda vorrei far suonare un woofer in medio alto cosa devo usare? grazie
@homemade_audio2 жыл бұрын
Ciao, grazie per il tuo commento, non posso offrirti una soluzione senza avere informazioni tecniche sul tuo midwoofer, per favore mandami il ref del driver oltre al tipo di progetto 2 o 3 vie, anche il ref del tweeter, altro dettaglio .
@d.s.w7779 Жыл бұрын
Where is the video to do midrange crossover?
@daisymaedaguipa8844 Жыл бұрын
Magkano Po mag pa set up pang motor po?
@user-lp5rq8hi1f23 күн бұрын
my psu getting very hot for this amp
@homemade_audio23 күн бұрын
@@user-lp5rq8hi1f yes it's normal 🤷♂️ because the class A amplifier needs a lot of power to work well, but instead of electronic power supply, it's recommended to use simple power supply based on transformer , diodes and capacitors.
@efendy4745 Жыл бұрын
7:19 bunun yerine ne kullanabilirim teşekkür ederim elimde malesef yok 😢
@homemade_audio Жыл бұрын
Hello, don't worry 😉 any 10k stereo potentiometer do the job well 👍