this guy is the Bob Ross of the DIY world. Just his voice and energy
@ggumfory4 жыл бұрын
He sounds like Red Green to me!
@clevelandgreg10274 жыл бұрын
kiss him...
@chrismoeness4 жыл бұрын
Happy little shelves!
@mandie14563 жыл бұрын
So true
@carpenterdom16395 жыл бұрын
I appreciate the fact you showed your shortcoming and how you addressed it. Looks good, is good!
@MikeLeeSr4 жыл бұрын
I want to thank you again. This saved me so much time and money recommending the timber lock screw.... I didn't even think of using pocket holes. It turned out great and held all 205 lbs of me with no flex. I did run reinforced studs behind before the drywall because I knew I was doing the shelves, but unsure on the way Iwas going to attach..... Keep up the great work.
@frankg8826 жыл бұрын
Drill a hole through your sponge the size of your holesaw, wet it put your holesaw through it and use it as a shroud when drilling. Keeps the mess down and keeps your drill bit/holesaw cool 😎
@HomeRenoVisionDIY6 жыл бұрын
Thanks Frank, I will give that a try. Cheers!
@realrussianreview11865 жыл бұрын
Great idea bro
@ryanpedersen57225 жыл бұрын
Thats a bloody good idea mate, cheers from Australia
@frankchu36145 жыл бұрын
Another way to do it is take the piece of sponge you drilled out of the big sponge, wet that, and put that inside your hole saw, and it will both keep your hole saw moist and cool, but it will also cushion your cut piece inside so that it doesn't get stuck all the way in the back of the well for easier removal. And it'll keep everything around, especially underneath from getting too wet.
@sarge97333 жыл бұрын
@@HomeRenoVisionDIY Personally, I tape my dust pan to the tiles just below the hole I'm cutting/drilling, and have a pot of water nearby to dip the bit into occasionally to stop overheating.
@danchiasson5 жыл бұрын
Great video as always Jeff. I would however add a few suggestions to anyone tackling such a project: 1. Be extra careful to check for wiring (or plumbing) in the wall when using long screws (i.e any fastener longer than typical 1 5/8" drywall screws). Unless the house is newly built or fully up to electrical & plumbing code, which is rare (and has protection plates for all cables & pipes intersecting through every stud), you run the risk of shorting cables or bursting a pipe. On a freshly tiled wall, this could be a very expensive repair. This is a common mishap that occurs when people try to wall mount their tv's and disaster strikes. 2. I wouldn't permanently seal the pocket holes with plastic wood. You might need to move, adjust, remove, or refinish the shelf. I would suggest using removable pocket hole plugs or hole covers, or just leave them exposed if drilled from underside (i.e. hidden well below eye level). My 2 cents :)
@bigjonbird14 жыл бұрын
You explain stuff very well. Not too much information but just enough. Videos are great, thank you.
@pdubs70695 жыл бұрын
You are awesome! I'm saying it again! So many tricks tips and different ideas to help me with my projects! Pocket holes- brilliant!
@Spencertk76 жыл бұрын
This is amazing and I can’t thank you enough for posting a high-quality video on mounting these kind of shelves.Your work is killer!
@HomeRenoVisionDIY6 жыл бұрын
Thanks we appreciate it. Cheers!
@freda27584 жыл бұрын
You are a weekend worrier's warrior.
@shiranifrances9153 жыл бұрын
A very nice honest person god bless u
@jhirae5 жыл бұрын
Great video, always love the floating shelves look but never knew how. Great tutorial 😃
@NextGenerationHealth5 жыл бұрын
That is a great way to hang a floating shelf! Thanks for the idea.
@HomeRenoVisionDIY5 жыл бұрын
Cheers Carl!
@paymanali47796 жыл бұрын
Again another amazing video. I can't wait to see the end results. Thanks Jeff for the efforts you put in the projects. Greetings from Holland.
@HomeRenoVisionDIY6 жыл бұрын
Cheers to Holland! The final reveal comes out on Saturday. Looking forward to hearing from you about the final product"
@StephenNu95 жыл бұрын
The porch screws is one excellent idea.
@balddeagle965 жыл бұрын
I can just see someone putting that timberlock through the 2x4 stud into the next room 😂
@salsaco51193 жыл бұрын
Omg im so happy that I found your chanel!!! Thank youuuuuu ☺️👌💯
@mtl10714 жыл бұрын
Will you please let me know if I can use this installation for bookshelves,? I love this idea..I want to install shelves on both sides of my fireplace. I love all your videos!! Very clear information about everything. Very helpful to understand easy what you're looking forward to.
@alainpederian6 жыл бұрын
I love how efficiently you work! Great video! Keep up the good work :)
@HomeRenoVisionDIY6 жыл бұрын
Thank you Alain, clean and organized my 2 favorite job sites.
@franzrobochicken62115 жыл бұрын
I like your videos. I subscribed to your channel. Thank you for sharing your wealth of information and also being very clear and good camera work. 👍👍👍
@HomeRenoVisionDIY5 жыл бұрын
This channel has the best camera work in the business. Cheers Max!
@IAmAFixer5 жыл бұрын
Thanks for sharing! I have never heard of those screws before. Unbelievable strength for such a small diameter. Great video!
@djblock2155 жыл бұрын
Yea they're awesome. I used 4 of them to hold up my patio roof to the posts. Works like a charm but they're expensive. At least $1 a piece.
@bitcoinmaster36344 жыл бұрын
Thank you for the Timberlok idea. I really didn't want to mess with the metal dowels.
@williampalmieri48475 жыл бұрын
Would love to watch you install the range hood you have outlined in the background. How to attach it to the tile etc
@Dangit-Dave6 жыл бұрын
Great videos! Have you considered adding Amazon links to the products and tools you use. I really want to buy the laser tool and support your channel at the same time!
@FrankO-ek1ec5 жыл бұрын
d m it’s up there on Amazon I already checked Loloo
@ttfweb16 жыл бұрын
I like the use of the timberlok screws - smart. I did similar with dowels, and I pinned it to the sidewall (put blocking in beforehand). It's not always an option, but I'll add the support if it's there. Nice video.
@HomeRenoVisionDIY6 жыл бұрын
Very true. I like to block up whenever I can as well. Thanks for the comment.!
@michael7v64 жыл бұрын
Love this guy!!!
@Jonasvanjozi4 жыл бұрын
Hi Jeff. If you could have some footage of your finished jobs to show how cool it looks that would be great. I want to show my wife your ideas but she’s interested in how the finished kitchen looks, not the job to get there! Thanks man. Your videos are very informative!
@allanpennington4 жыл бұрын
The weak point of this method isn't the fact that the screws will never fail, its that the timber can split along the grain line of the shelf or stud and that the bearing surface of the load is on such a small surface area, namely the size of the screw head diameter.
@atticus25815 жыл бұрын
"anybody willing to tackle this project at home is probably more than capable of finishing their wood." 🤣
@MP-yz6sb5 жыл бұрын
Wow I really like this look. Not sure I’m brave enough to try it though.
@olliecrow35474 жыл бұрын
Not me...brave enough that is.
@manggy6 жыл бұрын
Hi Jeff, great video. I really want to try to do this but I don't have much experience. My main concern was hitting electrical and all sorts of terrible things driving timberlock screws in, but apparently since you had the wall open, you knew that nothing was going to happen. How would you advise if I didn't know how the electrical ran behind the wall? Thanks.
@kylelove9275 жыл бұрын
Very nice work... AS USUAL.
@its_evers64453 жыл бұрын
Honest question and not trying to be a troll but I'm truly wondering if have any worries/concern/opinions on that screw you had right on the end corner? I just bought my first house (woot) and im in the middle of remodeling the whole inside so its fresh and clean when we move in (we have kids 3 and 6) so we want our forever home percent before moving in! I've subscribed and have watched a ton of your videos! You've helped a TON! Thank you for all the videos! GREAT channel.
@lcook08254 жыл бұрын
Nice job.
@ThorMaxx4 жыл бұрын
Love this vid....but even though 16's is a standard in North America, there are some shoddy builders the put studs where ever they please...like Minto....i have walls in my house...some are as much as 22...needless to say installing floating shelves (especially Ikea ones) are super fun (insert sarcasm).
@monawarrajayki54453 жыл бұрын
Thank you very much
@MrNathandoucette6 жыл бұрын
bought my Diamond bit at princess auto...works great!
@HomeRenoVisionDIY6 жыл бұрын
Nice, Nathan is the man!
@vincentlenci5 жыл бұрын
Jeff we'd make a great team, I'll make the mistakes and throw fits of anger you can fix them and smile Lol
@nywvblue3 жыл бұрын
It never would've occurred to me to drill such a large hole through the tiles. Is it because the mounting screws go in at an angle? Anyway, dang, you make the tricky look easy. And: Brilliant thinking to mount the shelves upside down!
@joseestevez59356 жыл бұрын
Jeff i learned a lot from your videos, thanks. this is the way that i use to do it: 1 step i use the masking tape and put on the wood and mark the holes then after that i work in the level and put the masking tape on the wall and make the holes on the wall. 2 step : i use screws of that size with bigger gauge, cut off the head of the screw, put the lead plug on the wall then the screws. use the mark thar we make on the wood make the holes and put on the piece of wood on the screws the i put on the wall. and that its. i thing it a little bit simpler and clean and supports a lot of weight.
@lcook08256 жыл бұрын
That is the best project yet. Thanks Jeff.
@HomeRenoVisionDIY6 жыл бұрын
Glad you liked it Larry! Cheers for the comment
@giovanaalmeida70145 жыл бұрын
Your number one fun. 👍😊
@TranTheClever4 жыл бұрын
O I'm definitely going to make this!! 5:52
@j_dane95194 жыл бұрын
I like this approach, but I'm worried about hitting a wire or pipe with those long screws. One option would be to widen the tile holes by boring two side-by-side holes that partially overlap so you can feel one side of the stud for anything passing through. Another option is to use shorter screws that only go about 1.25" into the stud. I don't think you'd lose much strength from that as long as the screws are driven in so their heads are tightly seated against the shelf.
@HandleKingHardware5 жыл бұрын
Looking great!
@HomeRenoVisionDIY5 жыл бұрын
Thank you my Lord!
@wheeltowheel25613 жыл бұрын
Is there more detailed information on the size of the Timberlock screws used and the depth of the drilled pocket holes?
@RobertPWills4 жыл бұрын
Made the mistake of showing this video to my daughter...I'm using your 15-step Drywall Installation videos to help remodel my master bath. I removed garden tub and tile and installed a free standing tub so all the drywall behind the tub needs to be replaced. Time in the shower is getting your 'tile over tile' video treatment. So I've got a full blown renovation going on. Then without thinking, I showed this video to my daughter who just bought her first home. "Dad! I need a backsplash and some floating shelves!" I really need to get that kid a handy boyfriend. How old is your son??
@manofausagain5 жыл бұрын
Just know those screws and strength is measured in tension not in shear or bending. With such a narrow shelf the force of the cantilever will be a lot more then the actual weight. Not saying it won't work but just be careful in the assumptions you make about direct comparison.
@robertbutler80045 жыл бұрын
Manofausagain he would not be smart enough to know that!
@houses59415 жыл бұрын
manofausagain e
@nathan874 жыл бұрын
Completely agreed. I completely get that it's not meant to be climbed on etc but I'm still uncomfortable with the strength of that fixing, whether it's the screws or the wood itself. Would be happier to see another screw (or even a steel insert) in that end wall.
@Simmons23585 жыл бұрын
Velcro also works.
@jayrob74185 жыл бұрын
Lol
@JeroneJames194 жыл бұрын
I'm sorry about the last comment. I don't need the shelf with the brick backing to hold 250 lbs, but I need to know what anchor or screw will hold and not make a good amount of weight fall?
@lcook08254 жыл бұрын
Nice.
@jebusfreek66675 жыл бұрын
Where the heck do you find wood this thick? The best I can find is 2x?, so 1.5" thick.....
@geetarwanabe4 жыл бұрын
Wood merchants not your standard stores
@VJWLPN14 жыл бұрын
Awesome!
@lizzyh58084 жыл бұрын
Nice... is it easier to build the shelf before I tile the backsplash ?
@TheFdis10266 жыл бұрын
You are very easy to follow and it much appreciated. Can you do a video on subflooring,
@HomeRenoVisionDIY6 жыл бұрын
I am planning on doing a video on everything. Stay tuned.
@cjbfire954 жыл бұрын
I need you in my city!!
@tkinto3 жыл бұрын
Not sure if you’ll still respond to comments on this thread but wondering if in our kitchen remodel if I wanted to add shelves do I do it before the planned quartz backsplash and get the quartz cut to fit around it or drill into the quartz?
@tylermazerolle84754 жыл бұрын
Ive done a couple floating shelves, what do you think about using 3/8" lag bolts and cutting off the head of the lag. Drilling holes in the material and sliding it on the lags with some PL adhesive. Is there disadvantages to doing it that way.
@jayhova3 жыл бұрын
Good idea. Seems like that is just the metal dowel method. However, the dowels seem to be much thicker and sturdier than the 3/8 lag. When the lag is screwed in, it pulls in the wood very tight to wall. So the thickness doesn't matter as much. But if you do what you said, it wouldn't be as strong and the shelf might possibly sag a bit, with a decent amount of weight. The depth of the wood is a big factor.
@TranTheClever4 жыл бұрын
This is amazing!! Gorgeous 😍 3:26
@SandiRose20086 жыл бұрын
Can't wait to see the finished project. That kitchen's coming together nicely. Thanks for the video.
@HomeRenoVisionDIY6 жыл бұрын
Thanks Sandi, BTW Max is working feverishly on obtaining some new music and adjusting sound level. Thanks again for the imput.
@SandiRose20086 жыл бұрын
I love me some Maximum Moskal Multimedia! ; -)
@HomeRenoVisionDIY6 жыл бұрын
You and me both SandiRose27
@demmons855 жыл бұрын
how did you drill the pocket holes to receive the 1/2 inch screw head of the timberlock screws? all the pocket hole jigs i can find are for 3/8 inch
@bw79254 жыл бұрын
I was thinking about putting some floating shelves in my swimming pool
@Johnintoit6 жыл бұрын
Nice job, I prefer to use the pocket hole plugs then just fill in very minimal.
@HomeRenoVisionDIY6 жыл бұрын
sure, that will work too!
@Meonthemove124 жыл бұрын
Great job 👍 what tool did you use to make the initial pocket holes?
@Atr42Greasemonkey5 жыл бұрын
I always love your videos .But if the 1000 pound shear load strength of the screw split the wood how is that small screw going to support the weight ?
@HomeRenoVisionDIY5 жыл бұрын
no worries, not parking a car on that shelf.
@quam00914 жыл бұрын
Anyone have a link to this to at a Home Depot, Lowes, etc. I can't seem to find these anywhere.
@danielesposito97053 жыл бұрын
need to find a wood store near you, not a box store.. even then, there's no guarantee they will have 2 1/4, I can find that anywhere around me.. or at best, they have slabs which you have to mill..
@bambi0055 жыл бұрын
do you have tips on adding window blinds or rod to a shower window that is all surrounded by tile?
@BryanDannowitz5 жыл бұрын
I'm thinking of doing exactly this in my home office. If I attach a 5' piece to three studs, do you think it should support something as heavy as a line of books? I noticed you mentioned that you were just putting decorative pieces and not a stack of plates on it. Thanks for the video! Very inspiring!
@HomeRenoVisionDIY5 жыл бұрын
Hi Bryan, there are other ways to hang shelves that hold a lot of weight. perhaps that would be a better option. Cheers!
@redwood19574 жыл бұрын
Those long screws look as though they Could go over 1/2way into the stud. If there were a pipe or wire through the center of the stud there would not be a nailplate to protect the item. Now you have problems if that happens. Thank you
@MTEXX4 жыл бұрын
yesterday hit the back of a service panel with 18ga brad nailer. big oops... the service panel did its job thankfully. wonder what those structural screws would do.
@nelsonrachmaciej88966 жыл бұрын
Can't wait to see the exhaust fan video!
@HomeRenoVisionDIY6 жыл бұрын
I don't think we got that step on video. But It is in the final reveal. I am available to answer any questions you might have.
@JeroneJames194 жыл бұрын
What screw or anchor should I use to install a shelf designed to hold over 250 lbs into brick that has sheet rock layered on top of it?
@zoexia22723 жыл бұрын
Hi Bob what color of grout you used in that subway tile? thanks
@davec.31984 жыл бұрын
Great project! I love undercab lighting....this shelf is begging for a clean, thin, LED light. It is too difficult to go back and do, but maybe next time run a low voltage cable through the wall before tiling. :)
@masonfreitas48543 жыл бұрын
What is the length of your timberlok screws? 8inches? 10inches?
@quam00914 жыл бұрын
Do you happen to have a link to this product from the big box stores, Home Depot, Lowe's, etc. Looking to pick these up but can't find this on their website.
@vinnie1123946 жыл бұрын
Thank you for all your videos. Do you ever have to dip that bit in water to keep it cool as your drilling. Or does that bit not need it.
@HomeRenoVisionDIY6 жыл бұрын
not when drilling ceramic!
@MTEXX4 жыл бұрын
1:11 I love lag screws. Those look like the next gen.
@mirandasi83024 жыл бұрын
everyone knows this technique splits the studs that's why no body does this, not to mention this is a weakest hold for a floating shelf. try metal brackets (ikea style) or french cleats.
@abdullahmuhammad66223 жыл бұрын
What type of wall is behide the tile the screws went in easily Mine wall is made from reinforce concrete can those screws work?
@MrMeangreen13106 жыл бұрын
I live in Ohio and I wish I had Canadian neighbors. Damn lakes.
@yikesdotnet5 жыл бұрын
i'm about to endeavor on this project myself! my question is this: we're doing much longer shelves and i saw in the comments some people recommending installing the screws through the bottom and not the top for weight. would that be advisable with longer shelves?
@HomeRenoVisionDIY5 жыл бұрын
Hi Katy, the length of the shelves does not matter. place a screw in every stud if you like. Cheers!
@JonathanIvy6 жыл бұрын
Can you tell me more about the shelf? What kind of wood is it? Where would I buy it?
@HomeRenoVisionDIY6 жыл бұрын
the box stores are all carrying this stuff now.
@JonathanIvy6 жыл бұрын
Home RenoVision DIY I have been to Lowe’s and Home Depot and no one knew what I was talking about, I’m really wanting to do this project but I can’t find the main material! Can you give me a link or a product name? Thanks!!
@JonathanIvy6 жыл бұрын
I Found it!! www.lowes.com/pd/Live-Edge-Natural-Wood-Pine-Rectangle-Coffee-Table-Top-Actual-2-in-x-8-in-x-48-in/1000449699
@kalkap5 жыл бұрын
@@JonathanIvy thanks for this!
@atlskyline15 жыл бұрын
@@JonathanIvy That's not it. He is using a 2.5" thick piece. The one you found is 2"
@itzakad0ozi35 жыл бұрын
You've mentioned the screws itself can handle the 1000lb load, but i was curious about the wood. Do you happen to know how the shelf is holding up after some use?
@HomeRenoVisionDIY5 жыл бұрын
I was actually back after a year and everything was just fine thanks!
@onlyboutthabizness6 жыл бұрын
Hey I love your videos so keep um coming for us DIYers.....I'm in the process of changing a shower valve in a wall. I soldered the elbows but got incredible bubbles all around. I'm afraid its not done properly. How can I ck this with the water off and even more so, how can I remove the clumps?? I'm confused as I heated awhile to make sure hot enough but this is what I kept getting ....HELP
@HomeRenoVisionDIY6 жыл бұрын
sound sot me like you didn't clean the copper properly. sand it until it shines even past where you will solder and then use flux. heat from 1 side and then place the solder on the other side. when it starts to melt you know it is hot enough. Don't over heat as well. Have someone on the phone with you opening the water to check. Good luck!
@jimmyron31954 жыл бұрын
have you ever heard of a torsion box? foe me its an easier and just as strong solution, plus more stable than a thick piece of lumber.
@kojimasan4444 жыл бұрын
What about if we put a backsplash on top of the previous tile. Like there's backsplash, then tile. Then whatever is behind the tile?
@HomeRenoVisionDIY4 жыл бұрын
This trick is only for when you have renovated and know what is in the wall you attaching to. hanging floating shelves blind is dangerous.
@billsmith82466 жыл бұрын
What kind of laser level is that you use? I dig your videos. You make it seem less daunting with how you explain things!
@HomeRenoVisionDIY6 жыл бұрын
simple dewalt dual line goes for about 120 bucks at the store.
@danieliscrazy1115 жыл бұрын
Is the length that the screw is in the shelf slab sufficient to hold such weight? I know the screw is strong but won't the little chunk of shelf it's actually gripping risk snapping or cracking?
@HomeRenoVisionDIY5 жыл бұрын
that all depends on how much weight you are putting on it. I would not for instance store all my plates on there. But it is great for use like display as seen in the picture.
@dee7803 жыл бұрын
What do you use for drywall to keep this sturdy no tile on wall
@bethmaldonado92413 жыл бұрын
How bout glass tiles, will it crack them? We have a glass mosaic tile splash
@NoRoads2AllRoads5 жыл бұрын
Do they sell that at Lowes or HD> Never seen these... they'd look great as steps on an open staircase
@HomeRenoVisionDIY5 жыл бұрын
Hi Salvador, they are softwood so not a great choice for steps over time. I would suggest using a hard wood for that. Cheers!
@Tehcarp5 жыл бұрын
plastiwood scrapes real well. Card scraper :)
@doubleblack58975 жыл бұрын
Hello Jeff, love your content. I am looking to do a similar thing for a fireplace mantel..... but I cannot find that type of pre drilled shelf anywhere. Is the the any chance you could tell me the store and model number of the product. Thanks
@doubleblack58975 жыл бұрын
I rewatched the video and found them...... thanks again you are great.
@marymack41055 жыл бұрын
@@doubleblack5897 Where did you find them?
@kenoftheyear15 жыл бұрын
@@doubleblack5897 Yes, where? Having a hard time over here.
@iandroo8886 жыл бұрын
what is the thing u used for the shelf? you never exactly mentioned what its called
@anonymousSyllabic5 жыл бұрын
Wood
@tahirnasim33256 жыл бұрын
Hi, could you please make a video on putting a TV mount on a concrete wall? Thanks
@HomeRenoVisionDIY6 жыл бұрын
follow m,y t.v. mount video and use a masonry bit and tapcon scows. Cheers!
@chrisbyers44946 жыл бұрын
Nice work, Jeff. Can you clarify where the link to the video is for the full kitchen reveal?
@HomeRenoVisionDIY6 жыл бұрын
Hi Chris, the final reveal is not yet released. I believe it comes out next week.
@hmg89154 жыл бұрын
I'm sure if Jeff had been removing that shelf and seen a screw in the bottom of the shelf he would be laughing and criticizing the contractor responsible. (Just something to think about) Hey Jeff Thanks for the video and the honest non edit.
@jonathannorman73565 жыл бұрын
Where did you find these shelves? Can they be bought online?
@Biddybalboa5 жыл бұрын
its just wood
@cwr86185 жыл бұрын
Hey Jeff, is it possible to replicate this in a bathroom where I could tile/caulk the shelf for toiletries? I have a tiled shower with no shelves or anything. Sucks big time!
@HomeRenoVisionDIY5 жыл бұрын
sure if you install it opposite the shower head. seal up the shelf with polyurethane first and then silicone the shelf to the tile for extra protection.
@cwr86185 жыл бұрын
@@HomeRenoVisionDIY NICE!!! Sorry to bug but one last question - how the heck do I find the studs if there's already tile up? I suppose I can see if stud finders will penetrate that material...
@ThiagoHenrique-zk4mp6 жыл бұрын
Muito bom o vídeo Ajuda bastante todo mundo Parabéns parabéns
@HomeRenoVisionDIY6 жыл бұрын
Very much appreciated Thiago, great to hear from you again!
@rmontana36935 жыл бұрын
I think he is keeping 18" of clearance from the counter top. This in my opinion is a good idea, the chinese cabinet guys left me 16.5" and the coffee maker doesn't fit, a bunch of things don't fit. As a homeowner it's up to you to keep a close eye on what is being done and to have at least a basic understanding of how things work.