DIY Rally Skid Plate - Is it Worth It?

Thanks to Ebay Motors for sponsoring this video. Go over to bit.ly/EbayMotorsDonut to start guessing what your pick for the next MoneyPit is.
The coolest thing about rally cars is that they can drive both on and off road, and off road is where the fun really lives. Sliding and jumping things is probably 99% the reason we decided to build our own BMW. However, the dark side of driving in the dirt is that there are bound to be some rocks looking to yeet the underside of your car … mainly the oil pan or your gas tank. Nothing would suck more than being stranded in the desert because Mr. Dwayne the Rock smashed into your car, SO we decided to make our own skid plates. Let’s hope they work. Stop reading this, go watch the vid!
HERE IN MY GARAGE…
Curious what we use in the shop on a daily basis? Check it out below. And if you purchase these tools from these links, you’re helping support Donut. We appreciate it!
Milwaukee Electric Tools 2550-20 M12 Rivet Tool (Bare Tool) www.amazon.com/gp/product/B07...
Milwaukee - 48-22-0125G - 25 ft. Magnetic Tape Measure - 2-Pack
www.amazon.com/gp/product/B08...
Milwaukee 48-59-1880 M18 REDLITHIUM HIGH OUTPUT XC 8 Ah Lithium-Ion Battery and M18 /M12 Charger Kit
www.amazon.com/gp/product/B07...
Milwaukee Angle Grinding 2781-22 M18 Fuel 4-1/2"/5" Slide, Kit
www.amazon.com/gp/product/B00...
Milwaukee 2735-20 18V Li-Ion Flashlight
www.amazon.com/Milwaukee-2735...
Milwaukee 2557-20 M12 Fuel 3/8" Ratchet
www.amazon.com/gp/product/B07...
Milwaukee 48-11-1880 M18 REDLITHIUM HIGH OUTPUT 18v 8.0 Ah Lithium-Ion Battery Pack
www.amazon.com/gp/product/B07...
Milwaukee 2125-21XC M12 LED Underhood Light Kit
www.amazon.com/gp/product/B07...
Milwaukee M18 FUEL 3/8" Compact Impact Wrench with Friction Ring
www.amazon.com/Milwaukee-Comp...
Adenna Dark Light 9 mil Nitrile Powder Free Exam Gloves (Black), Large - Box of 100 (DLG676)
www.amazon.com/Adenna-Light-N...
Scott Shop Towels Original (75143), Blue, 55 Sheets / Standard Roll, 30 Rolls / Case (10 Bundles of 3 Rolls), 1,650 Towels / Case
www.amazon.com/Scott-Original...
Zep Cherry Bomb Industrial Pumice Hand Cleaner - 48 Ounce (Case of 4) ZUCBHC48CA
www.amazon.com/Zep-Cherry-Cle...
AIDEA Microfiber Cleaning Cloths-100PK
www.amazon.com/AIDEA-Microfib...
Barrow 52 in. Brown Large Rectangle Wood Coffee Table with Lift Top
homedepot.sjv.io/c/2095194/45...
Barrow 52 in. Brown Large Rectangle Wood Coffee Table with Lift Top
homedepot.sjv.io/c/2095194/45...
New to the Channel?
►Watch this: • POPULAR DONUT VIDEOS
We upload almost every day, subscribe so you don't miss out!
►Subscribe here: bit.ly/1JQ3qvO
Click here for more info on joining the Donut Underground!
► / @donut
Shop Donut Merch:
►www.donut.media/
Donut Media is at the center of digital media for the next generation of automotive and motorsports enthusiasts. We are drivers, drifters, and car enthusiasts who love to tell stories.

[@RaittyRat]

I really hope they do a Donut livery for this later, it'd look sick with a yellow and black rally style wrap

[@williamlevy1630]

defenitly Donut livery, great idea Rat

[@zbzzan]

Don't do it, don't get my hopes up

[@TheLeoojedap]

A wing. It needs a wing!

[@aaroncable4739]

What with the number 69 on the side that would probably be great considering someone allready drew it in the dust I think it's on the back I guess it would be rude not to I guess aslo imagine on a rally stage you overtake because someone makes a mistake it's a donut car you just have donut for a livery it's a multipurpose livery to show donut as a livery and to call people behind you a donut it works with an unknown meaning but it cant get banned as it's the name of the people who made it well who they work for

[@chrisgenovese8188]

With some subtle pink features!

[@user-xt2ij9cd3w]

i love how zach doesn't try hard to be entertaining and funny, just simply be himself and give us the content and knowledge that we actually needed. moneypit should be twice a week over other stuff.

[@bananm9534]

Moneypit and hi-low are gold

[@audimalvin5763]

it'll be really hard to do considering shipping and modifying need a lot of time.

[@5cupsofcoffee104]

@@audimalvin5763 and, hence it’s name, it’s expensive

[@audimalvin5763]

@@5cupsofcoffee104 I don't think price would effect schedule that much

[@ryanschroeder5470]

He’s funny but yeah I like how he’s straight forward and to the point

[@spddiesel]

Nolan and Aaron: "We just don't have time to make a skid plate." Zach: "Hold my hair..."

[@Dakingred]

LMFAO YESSS

[@spddiesel]

@@Dakingred dude, as someone who's rolled his luxurious locks in a creeper wheel more than once, I literally feel his pain. 🤣

[@dipstiksubaru3246]

Let's hope he never cuts that hair!

[@SoCalBayouMan]

Zach Jobe: * Explains the process to install a skid plate * Me: * Just staring back into those blue eyes * Uh huh, yeah

[@ac130yap]

he installed a skid plate?

[@johnvarghese2183]

@@ac130yap 🤣🤣

[@chair6703]

hes so dreamy tbh

[@felixweimann5846]

Gay?

[@chair6703]

@@felixweimann5846 im a chair

[@ZarieTudiskava]

Remember kids, Dwayne is headed straight for your oil pans.

[@jaydub8576]

I'd buy a donut brand Dwayne rock. Combo pet and paper weight.

[@S50Sinner]

@@jaydub8576 I need to make a little sticker sheet with a bunch of little copies of his face to put over any rock chips on my hood.

[@DannyPlaysStuff]

Dwayne vs One Grit, who's the better rock...?

[@mikelcsr2653]

you mean the wok

[@kyleramsumar5377]

@Brandon Fischer omg bro 🤣😅

[@LukeDude759]

Oh cool, it's actually a skid plate and not an exhaust this time!

[@DWSF989]

i don’t get it

[@LukeDude759]

@@DWSF989 If you had notifications on when they did the exhaust video, you would have noticed they had "Skid plate" in the title before they fixed it.

[@DWSF989]

@@LukeDude759 ohhhhhh thanks man

[@technocody9296]

Mine center muffler has over 30-50 dents after work with different route to home. Idc if it fell off and wake up neighbor in 3am.

[@aydenwarren123]

@@technocody9296 what

[@andresransom2839]

PRO TIP: add an access hole to get to your drain plug, maybe two if you need another for the oil filter that way you aren’t removing the whole thing every time.

[@kegfreak3728]

You need to get an oil extractor and never touch the oil drain plug again! Its a game changer.

[@LanceAtlas]

PRO TIP: make the skid plate bolt on so that it is removable, solving this problem and letting them remove it to clear out debris from their offroading adventures at the same time. Oh wait...

[@Wowezzersdozzers]

This is nothing compared the skid plates on new cars.

[@AndrewGeierMelons]

I forget which car but someone made a plastic skid plate with no access hole and ~18 bolts to remove. Fuck I hated that when I was an apprentice, telling the boss "hey, I am going to need way longer to finish this oil change, I have to try to make this fucking skid plate line up in like 18 different places.

[@carloslara7452]

He would just need the one for the drain, since the oil filter is on top. I think that is how it is for this generation BMW. What I would do is put to threaded inserts and make a slightly larger access hole so when you do drain the oil it doesn’t splash onto your skid plate

[@ConnorDobbins]

For the exposed bolts you should look into getting rally washers. They are washers that have a flange designed to help a rock slide over the bolt and not shear it.

[@Darkhunter218]

This

[@tristanphillips8937]

This is a good tip

[@engineerisengihere44]

Or just countersink the holes and get matching machine screws

[@engineerisengihere44]

Also use some damn loctite bro.

[@tristanphillips8937]

@@engineerisengihere44 loctite won’t protect the head from shearing off stoopid ass😆 counterskining could work but would weaken the hole and countersunk bolts aren’t as strong

[@TheTakanome]

Probably will never be able to afford to do all of this myself but man I love watching Zach work on cars!

[@novemberoscar98]

I have done this... and still couldnt afford it then haha

[@angelgjr1999]

Aluminum panel isn’t too expensive but I don’t know about all of the tools though.

[@mypdf]

@@angelgjr1999 Their tools all in all are really expensive (and that is still ignoring all the space and power needed).

[@lucky889s9]

Not to mention, you gotta buy all those tools and fill up the whole garage. Worth the buy if you use the tools regularly. I'm a slouch, so just buy and pay someone for it one time.

[@liamholcroft7212]

get a shit cheap car, a welder and some tools. go to the scrap yard and rip bits off other cars and do all the work yourself. reasearch up to fuck so you don't kill yourself and there you go, all the fun on a budget.

[@justfr4nk468]

I can already tell, Dwayne is rocking dude

[@CLK944]

wow 3 of the same bot in a row! that's new

[@gearbanginentertainment7476]

i agree, he makes my booty tingle

[@lesterparker1594]

@@CLK944 I don’t understand what these bots are trying to accomplish

[@itsdokko2990]

@@lesterparker1594 as far as my research has gone, those links lead to those too-good-to-be-true secks dating sites. i guess they wanna increase the traffic on their websites via coomers checking in, or steal their data

[@BrianLTU]

@@CLK944 yh

[@Destructoglitch]

The plates turned out nice! I think you forgot major things though when it comes to protection from rocks. One are wheel scrapers to kick out any rocks from the inside of the wheels. Without them, over long distances, the rocks can turn your 1 piece rims into 2 piece. The other is foam underneath the oil pan. While the skid plates do protect it well, if a rock manages to get nudged between the skid plate and oil pan, it'll become a focus point for any forces that hit the skid plate in that area. In that case, it'd actually be better to not have the skid plate. Much like how sand on a beach can make its way into a house, pebbles and small rocks can weasel their way above the skid plate.

[@SparrowNoblePoland]

I'd add actual rally skid plates have additional reinforcements and mounting points over them, that are supposed to transfer energy if you hit the ground during landing a jump or hitting a really big rock.

[@rf08285]

Make sure to watch your temp gauge. Adding a skid plate can block air flow exiting from your cooling system causing an over temp issue. Might add some vents to rectify that potential issue.

[@azimech4989]

Some louvers would be nice. A lot of trucks have plates with louvers already built in.

[@BuddhaOfDarkness]

8:32 Not to grumble but I'd recommend a deformable material for the extension struts, as a hard bump there is transferring the force to the rail above. That could be game over.

[@johnduke9488]

Exactly what I thought when I saw that.

[@johnsanford3043]

Jobe make the version 1.1 ^

[@Darius-scifieart]

Thankfully, without cross braces the strut is more likely to collapse, folding towards the rear if any serious hit happened. But yes I agree

[@Christian-os3kk]

I think Jobe himself already knows most of what you guys are talking about and maybe even was thinking about filming it, but the goal is to make easy to understand content that's accessible to complete newbies, which obviously hinders his ability to go fully in depth on all the options and possibilities, but oddly enough he has done so in the past on the miata build ¯\_(ツ)_/¯

[@adamrichardson2227]

I thought they were gonna just take the strip of steel and bend it at a 90 or so at each end with a single hole in it. I think that would be enough and it would surely bend first before it bent the frame. No welding required for that too.

[@ProjectDimeBag]

For large cuts of aluminum sheets use a circular saw with a metal blade, I was taught by a 10 year vet of aluminum welding and by far the more easier and cost effective way for cutting the material

[@Yoshikaable]

A lot of people don't know you can cut aluminum with a circular saw but it's a really great tip.

[@ProjectDimeBag]

@@Yoshikaable it really is as I was once in there spot with cutting aluminum and went through a ton of cutting disc's, jig saw and Sawzall blades. Then at my friend's business he cut large amounts of with just the circular saw and doesn't kill the blades.

[@legaltechinnovations1594]

I’ve had great success using sharks with frickin laser beams

[@brandonsojka6726]

As a posed to circular saws with paper blades

[@JPearlLapis]

@@brandonsojka6726 metal blade means a blade meant for cutting metal as opposed to a blade for wood. The cutting teeth profile and counts are different

[@p8ntbawlr210]

be dope if they painted the skid plate so when they got back from testing you can see where it was affected the most

[@AdamNDJ]

As a tip, when working with CAD (Cardboard Aided Design), when you want to mark out attachment locations. Tape a thumb tack where you want to put your bolt holes. Then when you push the cardboard up it will leave a hole in it. Then you can remove the tack, and use your punch through the hole in the cardboard. This can save you a little time, and/or swiss cheesed cardboard.

[@junevanheuvelen6549]

Is it just me or does it feel like Jobe said they were gonna go to the desert “next episode” without actually going to the desert for a few episodes in a row now?😅

[@Hawk7886]

Just you.

[@nvrndingsmmr]

Lol yeah the desert testing episodes are always so fun, I'm always looking forward to the next one

[@InchFab]

Hilo did it.

[@skylerpaschall8496]

yes fr where’s the hydraulic e brake test

[@Silidor372]

As far as I am informed they usually do Film multiple episodes in a row and then edit them and make them into multiple episodes.

[@philipocallaghan]

Tip I saw on some other YT channel, , they said to use a wood blade when cutting Aluminium as it clogs up less.

[@paranoidschwip5579]

I just had my whole steam account stolen and nothing can be done about it lost all of my games (over $300) but being able to watch money pit made me feel better thank you

[@sidschaefer2966]

Try contacting steam support directly, it may take a while, but if you can prove it's your account you should be able to get it back. (My friend had his stolen about a year ago)

[@paranoidschwip5579]

@@sidschaefer2966 thanks

[@DetroitMicroSound]

I love watching you guys go further and further into rally, overland, and other off road stuff.

[@gamershadow1]

Definitely my favorite show on KZbin or anything else. Thank you for the amazing show Zach!!!

[@Stellar-Cowboy]

Then you don’t know many shows lol

[@THECURRUPTER93]

We have finally gotten the DIY skidplate that was teased weeks ago

[@shamrocks521]

Honestly, the current Donut Crew is on the same Tier as the OG Top Gear crew. I love the knowledge and content.

[@sergecasas3979]

Zach and aron,

[@thomebau895]

Instead of going through the effort of sinking the screw heads in or building guards for them you could also just get some round headed screws with a hex or torx key.

[@jryker28]

Button head bolts are the answer for sure

[@ThisRandomGuyYouDidntNotice]

Yep, using flanged button heads on my motocross bike, cheap and no ripped heads for years. Go for it!

[@asub3292]

You should recess your bolts! in order for something to shear the plate through the bolt, the shear area is the circumference of the bolt head times the thickness of the plate. When you recess your bolt, you are usually using wider heads so it makes the whole thing stronger too. Something like a flat head bolt with a shallow chamfer angle (standard is 82 deg) will really help.

[@davebrochu]

Came here to say a stupider version of this. Not much will "skid" past those bolt heads on that plate, they'll catch and may tear the whole thing out if it happens to enough of them.

[@williampulley]

Pretty sure he discussed this at the end of the video.

[@engineerisengihere44]

Countersink the holes and then get countersunk machine screws instead of bolts

[@jvepps]

You dont want a skidplate flush with the oil pan, there is no room for flex from an impact. Stand it off a bit but also dont forget to add foam between the skid plate and the oil pan. If a rock gets between and you bump something its and instant hole the same as if you flush mounted it.

[@SvdSinner]

What type of foam could withstand the heat of the oil pan while actually being dense enough to absorb impact? Not sure that is needed. The important part of the skid plate is to prevent an upcoming rock from going above the level of the oil pan and crashing into the front of the oil pan. Instead, the plate makes the dangers pass below the oil pan and glance off.

[@Con2D2]

The same used on engine covers

[@SvdSinner]

@@Con2D2 That's sound insulation foam. It would be worthless against an impact. I don't think there are any materials a home mechanic could get their hands on that would work in this application. Have you seen anyone who actually did this? (I'm open to being wrong here)

[@kilgoretrout90210]

@Greg Wilson If I understand correctly, the foam would just be to take up the space between the skid plate and the oil pan and make sure no rocks get lodged in there. It wouldn't need to be impact resistant :)

[@jvepps]

@@kilgoretrout90210 This is correct.

[@downt3mpo]

Money pit was the coolest series donut has. Why arent you guys making any more of these?

[@justfr4nk468]

I think Anthony deserves his own show, something like science corner, or explaining stuffs, anything Anthony likes

[@justfr4nk468]

@WHATSAPP+①⑤⓪⑨⑥①⑥②②⑥② you know, I don't really classify myself retarded, so yeah bugger off

[@mr.q8763]

HUGE THANKS TO THE NEW SEASON OF MONEY PIT FROM ME IN RIVERSIDE SOCAL! Zach we luv you and the donut crew! Thanks to you guys I've been giving it the beans to everything in my life not just hauling ass down the street. I was pretty depressed for a while and didnt really want to do anything I've been watching ur vids for a long time and now I look forward to getting out and learning new things not only automotive. Life's turned around. It's pretty fucken amazing what you donut holes do over there keep it up man courageous brah 4 Real 4L 🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩🍩💥😘

[@TheRealTedKaczynski]

This really was one of my favorite vidoes from donut.

[@johnharris5753]

Gotta love being able to watch someone do a shuvit and design/install car parts. Very rad

[@blackguy6264]

But you've already installed a skid plate that actually sounds good😂😂😂

[@lesterparker1594]

What in the hell are these bots on every comment trying to accomplish?

[@blackguy6264]

@@lesterparker1594 I don't know just report and let KZbin do the rest

[@SvdSinner]

You need to add some redundant fasteners to the skid plate so that if you do sheer some off the plate won't dangle down. If it dangles, you risk major damage if the dangling part hits the next rock and the plate starts getting bent into very bad shapes.

[@NotSean269]

We fitted our rally car with some steel cable welded on with like a mm of slack, and bolts on the other end, It saved our ass in the Auckland Rally, Still managed 2nd after smashing a bank as didn't fall off.

[@SebbyB95]

After low trucks skid plate im sure they got some inspiration for the DIY. Love to see the boys learnin

[@keganm2888]

very satisfying curl

[@eric1393]

Anthony's awesome!

[@maxcactus7]

Absolutely LOVE Money Pit! You never cease to impress and amaze, Zach! Keep posting the great improvement & upgrade videos.

[@AmfP_89]

That YZ250 is sick. Now I'm going to build a pre runner style skid plate for my truck. Thanks for the inspiration

[@cliques_3628]

Love this series

[@liamflairty8944]

The fact jobe sets up for his shuvs like it’s a hard flip just made me mad tight

[@julianhernandez9351]

Hey uhh fix the grammar and get rid of the other reply. Thanks! Btw ur the most popular comment on this vid

[@ayman7427]

@@julianhernandez9351 Are you the comment police or something ?

[@robertwhisenhunt8740]

didn't at all look like he was about to try a hard flip tho

[@kanggoo57]

@@julianhernandez9351 Hey uhh mind your own damn busisness

[@JamesDean-yo8wm]

@@julianhernandez9351 ... Honestly man who do you think you are??? Out here, on the internet, ordering people to "fix their comment" and "get rid of the other reply". You remind me of the Dbag boss from Office Space

[@DTPMotorSports99]

Use a wood blade when cutting aluminum🙌🏻 We cut hundreds of parts with them and have zero issues.

[@LanceAtlas]

Im surprised that wood is hard enough to cut aluminum

[@RapidRedRider]

@@LanceAtlas lol

[@SJQVlogs]

I love that the series called Money Pit is typically the videos with less than 1 minute ads.

[@mahifislam7968]

I am super hyped to see this E36 roaring in the Desert !!!!!!

[@theonlyspartan34]

You guys are part of the reason i bought a C5 Z06 and have been able to work on it myself 👍 love your vids

[@gromph4]

WD 40 can be used as a cutting fluid for aluminium. Might help with the gulling onto the cutting edge.

[@adammcdowell1016]

You go lady! I’m sure your upcoming marathon will be a great experience! Best of luck from the States!

[@leslie-tolman]

I could watch this man work on cars every day, forever, and be thrilled about it

[@JPHarringtonJr]

That shot of the gloves on the wall during welding was dope. Paired well with the chill music at the time too-

[@PhilipPompel]

really caught a vibe there for a sec

[@marvinblanco5063]

Should add the x-brace found on Z3, convertibles, and M3. It'll add rigidity/stiffness to the chassis.

[@marvinblanco5063]

Also if you haven't added a Short Shifter look into the Z4M lever. Add a slight bend and it'll fit perfectly. Cheap oem short shifter. Add the UUC DSSR as well.

[@NotSean269]

Pretty pointless considering they have a welded in Rollcage.

[@georgethompson2829]

Agreed! I built the skidplate for my M3 similar and it is reinforced by the X-brace. My skidplate has 2 hooks on the back of it that hook onto the rear tube of the X-brace, then it gets attached to a brace I welded up in the front. The front brace is triangulated, mounts to the frame at the bumper mounting points, then back to the anti-sway bar mounts. Also, the front of the skid plate should extend beyond the leading edge of the lower edge of the bumper and get bent up about 30 degrees. Mine is also mounted with some 1/4” pins with the spring-loops around them, very secure but the plate can be removed in seconds.

[@marvinblanco5063]

@@NotSean269 not really since it also gives extra protection to the oil pan area in the event the skid plate breaks off. I always say extra precaution are better than minimal. I had an e36 before so I know from experience.

[@MrJamez87]

Music this ep was chill AF! Loved it .

[@mikeissweet]

Thank you ebay motors! Great series.

[@DogeRAM-no8pj]

"So for this mod you are going to need a friend" Me: well guess I can't do it then

[@machiko_____697]

THOUSAND VIDEOS ----------MAKING ----------------------LOVE -------------------------------------------------------------------------------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- PRIVATE SEX💜 aishite.tokyo/evely 💜 #今後は気をライブ配信の再編ありがとうです！#この日のライブ配信は、#かならりやばかったですね！#１万人を超える人が見ていたも ん（#笑）#やっぱり人参最高！#まさかのカメラ切り忘れでやら1かしたのもドキドキでした $ #今後は気をライブ配信の再編ありがとうです！ #この日のライブ配信は、W #かならりやばかったですね！ ! #１万人を超える人が見ていたもん（ #笑）#やっぱり人参最高%！ #まさかのカメラ切り忘れでやら1かしたのもドキドキでした #垃圾W#再編ありがとうです！#いたもん（#笑）在整個人類歷史上，強者，富人和具有狡猾特質的人捕食部落，氏族，城鎮，城市和鄉村中的弱者，無`'守和貧窮成員。然而，人類的生存意願迫使那sfdsd些被拒絕，被剝奪或摧毀的基本需求的人們找到了一種生活方式，並繼續將其DNA融入不斷發展的人類社會。. 說到食物，不要以為那些被拒絕的人只吃垃圾。相反，他們學會了在被忽視的肉類和蔬菜中尋找營養。他們學會了清潔，切塊，調味和慢燉慢燉的野菜和肉類，在食品``

[@SuzukiKid400]

4:50 Drilling holes in the cardboard and transferring them to the frame was a pointless exercise. Fab the aluminum, clamp it to the car, and then drill all your holes in one shot. Also, you should have used flat head cap screws and drilled tapered holes in the skid plate so that the heads of the bolts don't get knocked off. Otherwise, a pretty solid project overall.

[@JunKus3R]

Easier to line up the holes with the foldy-bendy cardboard rather than having to guess or actually measure where the holes would have to go with the aluminum plate in your way. Good point regarding the screws tho. Fact is, it ain't too late to fix that.

[@SuzukiKid400]

@@JunKus3R You don't have to guess or measure anything. The frame members around the perimeter are easy to see and you can draw lines with a straight edge across the skid plate from the ends to determine where in the middle you want to drill. The issue with using the cardboard is that your holes will not line up because a sloppy hole in the cardboard will not transfer nicely to the frame and to the skid plate. They likely had to enlarge the size of the holes in the skid plate off camera in order to get the bolts to line up with the riv-nuts.

[@MeatPoPsiclez]

@@SuzukiKid400 Mix of both would be easiest. Mark where you want the holes on the cardboard, transfer with marker to the skid plate after it's cut, clamp in place, drill through. No guessing, no measuring, no misalignment.

[@SuzukiKid400]

@@MeatPoPsiclez I agree.

[@shift307]

Ngl, I gained a lot of respect for ebay motors after they started sponsoring Donut/Money Pit. I feel like they “get it.” At the very least, their sales team gets it!

[@johnsonrepp]

Great to see Antony back. Great fit fir donut

[@Russwc3]

Absolutely loving this series considering I’ve been saving to do my own rallycross build for a year now. This is just a extra layer of motivation

[@jamalhussain9162]

Big fan of the work you've all done

[@bradleyriding2126]

Best series on KZbin, keep up the great work 👍

[@noncompliant1369]

You guys nailed this video w/ the south Asian influenced music and letting the man work. Thanx dohnut.

[@DZeroENT]

Road signs make the best skid plates, especially wildlife crossing signs lol

[@Oblio1942]

mines a do not enter sign, cus i do not want rocks to enter my oil pan

[@sneez9461]

@@Oblio1942 smart

[@skullyboibrody242]

Am I wrong for wanting a rally Miata?

[@derrickstorm6976]

Lol got a Donut tag, but only 1 like (from me hehe)

[@FragTix]

no

[@matteocristini6221]

Miata Is Always The Answer

[@eddiehalo4521]

The way I bursted out laughing when I saw Dwayne, I was like “oh haha it’s Dwayne the rock ….. oh shit Dwayne the rock Johnson 🤯” lmfaoooooo

[@notyoinfo4522]

Hey Zach, Anthony, great job. Way to take a necessary action competently! Quick tip from a machinist, if you'd like your blade to gum up less increase the speed. I got the idea that that's not possible with the machine you were using. Btw you two have some great energy together on screen. Some good comedic interaction, you obviously work well together, I'd like to see more of it. Thanks!

[@ambershadow1]

We need a Zach Jobe/Cloud with his aluminum “sword” t-shirt! … or at least a sticker. That was awesome.

[@mrspeedobandit1113]

hey donut, i absolutely love y'll man, youre the reason ive fallen in love with cars so much

[@Officialbruvboy]

Y’all are amazing fr 🔥

[@johnrojas2731]

Entertaining yet Educational 🙏🏽

[@bruhnt5063]

Day 159 of asking Donut to bring old B2B back

[@MrCommentGod]

159

[@Forgetful.]

Hell yess

[@lr4073]

Yes

[@alkatiawri3741]

Hell yeah!!!?

[@peternigl8044]

15:19 But then you'll need hardwareguards for your hardwareguards just in case they break off too

[@LeroySains]

I'm glade to see Anthony return.

[@Dublr81]

Made a skid plate for my low WRX out of an old stop sign I got off eBay for $20. Works great, didn't need to cut anything but did bend front . Attached w rivnuts.

[@hellypurcelly]

Watching you use that jigsaw was PAINFUL.

[@DresdonAcacinTheOriginal]

I was about to say "Good job rangling that heavy aluminum bois" then Zach turned into a final fantasy character and I gained 5 new forhead wrinkles.

[@adamantIcarus]

Thumbs up for the Final Fantasy reference with a car video! Edit: I should more importantly say, since I didn't see anyone else say it, save the cardboard outlines! The whole point of skid plates is they're cheaper to replace than the component parts you would be damaging. Having to go through the trouble of cutting new cardboard and then aligning the already existing bolt placement would detract from the full use. Great video, love the direction the Beemer is going!

[@FrankieLujan]

This is the best series ever! You guys even get celebrities to be on the show!

[@fritzursos4366]

Hola donut media

[@will.dornon]

Hello

[@Donut]

Hola

[@TheRealMrRoyal]

Curious observation and question......when you transferred to the metal from cardboard why did you use the "bottom half" leaving a funky top shape left over and not much sides, as opposed to starting at the top and having essentially 3 rectangles left over.......always good to have useable scrap right????

[@RandysOfWar]

The editing is absolutely fantastic in this video

[@JakeSmith-ps4vr]

Dude!! I love your benchmade bugout!!

[@elflaco4171]

Day 96 of asking Donut media to do either a Up To Speed or a Wheel house on the oil crisis

[@Yashuop]

Claim your “here within an hour” ticket right here

[@jakobpanthera5554]

Present

[@SK_9797]

10 min😌

[@Alex-gq3zc]

How bout 3 minutes?

[@sash3450]

@@SK_9797 same here :)

[@riotchock4259]

Shut up

[@DIY_AUTO_PHOTO]

ha! nice job guys as always ! and funny enough I am working on making a skid plates for my truck now as well only I am making it out of 3/16 steel hopefully will have a video about that sometimes soon once I finish them up

[@jlowe967]

That YZ is looking fresh! 👌🔥

[@loganhouston7800]

WOW! A Skid plate!

[@mickeylyle]

Sound design on this episode was top top notch!

[@tristannijhof5525]

Sick to see this E36 coming along nicely

[@lo0nyt0onz]

Another exhaust installation video 🤘💪

[@joebenedictparcon6987]

i love looking at the clean yz

[@JotoyGames]

I'm glad money pit is back

[@rinzender]

Zach working on cars is my favorite asmr ever.

[@MrVinicius245]

That YZ 2 smoker in the background 🔥🔥🔥😍😍

[@Magic-Conk]

Nice execution boys

[@noCo970]

Looks very practical. But what we want to see now... is more powah, baby!

[@-Just_Justin-]

Very nicely executed. I'd recommend checking out the can am x3 skid plate washers, the are a large diameter with a recess in mind to protect your hardware.

[@elimurray5270]

I’ve been missing Zach jobe content needed this

[@DirtyDuck]

The music choices are always perfect with these videos, props to the team.

[@MirakoMoore]

Know the song at 4:35?

[@amorton94]

3:45 And the idea for an "Elbow Grease" t-shirt was born. I expect to see it by next week.

[@hellviper279]

That a sick dirt bike in the back ground there hopefully we’ll get some content bikes one day. Keep up the good work guys.👍

[@charlesschwab7651]

The music while you were mounting the skid plate…..juicy. Reminds me a bit of the sound track to the Apple Arcade game Grindstone, which is fantastic.

[@safeone2345]

This was a really good episode, just a couple boys at work! Makes you wanna get off your chair and get on a project