DJI O3 Air Unit vs Naked GoPro 11 - Real Estate FPV

[@TRONCATFPV]

Getting a lot of comments on this; the GoPro and O3 are both hard mounted to the drone. I've noticed micro-vibrations are pretty common for Naked GoPro's on smaller cinewhoops. Most of the time I soft-mount my GoPro's to combat this. I did this intentionally to show how both cameras compare when hard mounting. Clearly, the O3 gyro performs a bit better than the Hero 11 in this regard.

[@andytroy]

It could be that the GoPro uses a longer shutter speed, causing motion blur. That motion blur is more visible after stabilising. Try to use a shorter minimum shutter speed, that might fix it. I don't have any problem on my QAV-pro with hard mounting my GP11

[@pabsvisions]

What you mean exactly with soft-mount? You just un tight it or what?

[@neofotografie]

@@pabsvisions no he means with vibration isolation, i m guessing similar to whats done on the geprc cinelog frames...and visible on his pavo25 frame with those rubber grommets

[@skreamfpv]

I've noticed with my naked GoPro mounted on my Cinelog25, sometimes the battery rubs up against the back of the soft mount plate and I have to make sure that the battery is strapped down and not too close to that mount. I believe a lot of vibrations were coming from that. Also, I've noticed since I started using a custom printed vertical mounted naked GoPro that there seems to be some more front to back wobble now. And then the internals of the case can cause a bit of vibration as well. When mounted, move the GoPro around slightly and see if you can hear any creaking sounds. I've added some custom fitted foam to keep the camera internals much more secure and noise free inside of the TPU case. In my head, all of this makes since as to why the O3 has less vibration than the GoPro footage.

[@albertg968]

I noticed that too and was about to comment about that. I notice that on my videos I do for real estate time to time

[@Photonees]

The GoPro has alot of vibrations in the zoomed-in footage. The O3 is perfect smooth. Also, what you say about the O3 being darker in shadows, that is also a result of the GoPro having a warmer whiteblance. In photography, a warmer balance will make images look brighter if I edit them and push the WB to a warmer tint. For me, the O3 looked more natural. The O3 has a cooler Wb with a tint of green and the GoPro warm with a tint of pink. Have to look on my eizo, but I would say, that unless you compare, the O3 makes it a lot easier to film and without the weight of the GoPro, you get a lot longer flighttime and would even say, probably smoother flying with a lower RPM.

[@TRONCATFPV]

When I was first testing out the O3 I thought white balance would affect the shadows but I tested WB locked at about 3500 and 6000 and noticed little to no difference in the detail in the shadows. Perhaps with the newer firmware that would make a difference. Next time I fly it I'll try out various locked WB. Also both cameras are intentionally hard mounted to the drone to show that the O3 handles vibrations a bit better than GoPro.

[@mx118racer]

I find the same thing with so many content creators. Is micro vibrations on high end go-pros . On a side note try 4.3 2.7k on the 03 onboard u can a good vertical crop from that too .

[@Silas_Edel]

The thing is GoPro artificially brightens the colors in Camera. If you are gonna color, it simply just turn up the warmth, brightness, and shadows and then it will be better than the GoPro

[@SniperUSMC]

Have to agree with the colors and contrast on O3, thought it was shaded a tiny bit darker which probably may not be noticeable if not size by side.

[@glitchunicorn]

They both look realy really good. There are some aspects that I like one more than the other, but both are really workable.

[@FlightPattern177]

I really liked the color and warmth/brightness of the GoPro more, but between 2:50 and 2:60 I definitely noticed the Air unit has much clearer and less shaky picture.

[@TRONCATFPV]

Agreed! Both have their pro's and con's. It was interesting to see how the O3 handled hard mounting vs the GoPro.

[@FlightPattern177]

@@TRONCATFPV loved the video, keep ‘em coming!

[@PaulieShortcuts]

Did you have a problem getting that o3 in the qav? I see it’s made more for vista and cnc drones sells the o3 version of the frame.

[@extremeboatdockingmedia]

Nice video. O3 has a slightly larger sensor but something is off with the highlights and shadows. I think there will be a future update after September to incentivize RID updates.

[@TRONCATFPV]

Agreed, i'm not sure which FW update improved the video quality since I initially tested it, but i'm sure these details will be addressed in a future update!

[@extremeboatdockingmedia]

@@TRONCATFPV the most recent unlocked 10 but color in d-cine which was a great improvement. But I think they’re still holding it back.

[@ccc3]

This was a very nice comparison! Gopro seems to retain finer details slightly better, but is prone to jitter. One surprising fact is that if you switch the O3 to ultrawide and then crop vertically, you will get the same FOV as the GP11, even though O3 is 16:9! However, you lose gyro data in ultrawide, so you will have to rely on Rocksteady.

[@zizjzjjsjsj]

ys but weired for dji，they comparatively has a larger sensor😢gppro did a great job on maximize the ability of sensor

[@mahuuuuuski]

what model of drone are you using? thx

[@TRONCATFPV]

5:55

[@JeromeDemers]

did you know that if you film 4:3 on the o3 you can get the 16:9 and 9:16. Works ok.

[@stellarmediacollective7953]

My G4 Lumineer AIO is juuuuust a little too big to fit the o3 under! What a bummer. Maybe the naked kit will help. Otherwise, I'm mounting it toward the back to balance out the gopro on the front end.

[@maetthum]

nice vid! looks like the gopro is not very stable on this mount. do you agree?

[@InMotionAerialProductions]

That was a perfect house for the O3...great lighting in that one. I find when filming properties with less than ideal lighting that's where the O3 struggles a bit. For me at least it ends up being more work in post to try and bring out shadow details with the O3 footage. It's getting there though and it's impressive how well it does! Like you, the naked GP11 is the default for me with clients as it's easier in post to get the deliverable looking good and as you mentioned more clients in the real estate industry are wanting the vertical edits. Well done, great video showing the two side by side. My main rigs for filming real estate are almost identical to your back up. Love the Micro-Pro Whoop. My setups are running 3s 850-1100mah and getting 5-6 min. with the de-cased GP 11's. It's interesting seeing the different setups people use for professional work. Keep up the great videos, well done.

[@TRONCATFPV]

I dabbled a bit with larger 3s lipos like that on some of my 4s 2.5" rigs and really liked how it flew. O3 is definitely getting there and I hope they're able to improve the detail in the shadows with a FW update. Glad you like the video! 🙌

[@neofotografie]

May i ask what motors your using on a 3s 2.5inch setup and what your dry/auw is then? and flight time? i've been trying to build an indoor analog cinewhoop on an inverted beta85 frame and 1204 8000kv 3s at about 170g auw with runcam thumb pro...but it flies like trash :(

[@InMotionAerialProductions]

@@neofotografie I'm running 1404 4600kv on the 2.5". Auw with O3, De-cased Hero 11 and an 1100mah 3s is 171 grams. Like TRONCAT FPV I'm running the Gemfan D63 5 blade 63mm props with this setup. At this weight with this motor battery combo I"m getting 5 to 5 min 30 sec. flight times. Keep in mind that's flying indoors fairly slowly doing fly through tours. For the rare occasion I use these to film outdoors I'll go to a 4s 650 mah pack. Typically getting 4 and a half to 5 min outdoors where I'm flying a bit faster and more aggressive. I would recommend trying a 1404 in a lower kv on your setup. Hope this helps.

[@neofotografie]

@@InMotionAerialProductions thank you for your detailed answer!

[@neofotografie]

@@InMotionAerialProductions btw.. my issue was not mechanical but i used BF4.2.8 on it.... upgraded to 4.4 and its smooooth. Note to self: never ever use 4.2.8 again! :D. Now i get 3min on 650mah 3s on this setup, but i only use 400mah, cause my batteries are not very fresh anymore, so i guess there s room for improvement in that deparment and 4-5 min might be possible with fresh 850mah 3s. Also works on 4s but its a screamer then ;D.

[@LeonSTE]

Would you prefer the qav cine of the cinelog25 for indoor shooting? Thanks for making this amazing review!

[@AdamVenturesTravel]

what do you recommend for sharpness and noise reduction settings on the o3 air unit when filming real-estate videos?

[@EditsbyMinh]

Awesome video! Very informative! Is your quad sub250g?

[@thatguygrand]

I just put an o3 inside the droneco snapshot and this proves to me that I can get away with real estate just with that, definitely doesn't fully replace a gopro though

[@victorlugardo3703]

I’ve watched all of your videos and your format and execution just keep getting better! Your thought process of explaining complicated subject is in synch with the way my brain is wired. I also appreciate your willingness to share what many would call Real Estate FPV trade secrets. I am debating whether to buy the 2.5” or 3.5” Qav-pro?

[@SniperUSMC]

I am debating 2.5 inch or 3 inch, not wanting to go larger then 3 inch because of the weight and manuverability of the 2.5 inch, 3 inch would be more stable though and only 43mm wider and longer than 2.5 inch

[@PattyFlipz]

Hey thanks for this video. I usually fly with a cinelog25 w/naked gopro10 and was always thinking of a back up cinewhoop, My buddy was having issues with his PAVO25 and gifted just the frame to me recently. I chucked all my spare components in it and a O3 AU for fun to see if I can compare them as well, just sorting out the throttle response now, but I'm glad to have watched this because I can now see the potential! Cheers.

[@DudeMaybeSomeday]

Does the Pavo25 readily accept the o3 unit? Looking into doing TronCat Pavo25 build but using the o3 instead of the caddx vista.

[@AdamVenturesTravel]

@@DudeMaybeSomeday same! I would also love to do this. did you run into any issues fitting the o3 into the pavo 25?

[@AboveAllVisuals]

Did you have it on auto or iso 100 with regular 120 shutter speed?

[@mahmoudelsayedshahin]

Can this drone setup carry a full gopro or a gopro without battery ??

[@Taufik.Moktar]

Hi, Dji 03 is stabilization with rocksteady or gyroflow? Thanks

[@skreamfpv]

Crazy, I didn't expect that the O3 would look that good in comparison! When you do the zoom ins you can see there is much more jello in the GoPro and hardly any in the O3. Do you think that it's because of the difference in how the cameras are mounted?

[@TRONCATFPV]

Right? I was surprised lol Both cameras are hard mounted and footage stabilized through gyroflow. I've noticed when naked GoPro's are hard mounted on smaller builds like this, you run into micro-vibrations pretty easily. I normally like to run a dampened mount for my naked GoPro's to combat this and am designing a 3d printed dampened mount for the QAV. It's cool to see that even though both are hard mounted, the O3 gyro handles those micro vibrations a bit better than the GoPro!

[@skreamfpv]

@@TRONCATFPV very interesting! Im curious to know if you recorded with any stabilization on the GoPro or do you stabilize in post? And also, is the O3 recording with stabilization as well?

[@volodymyrboryslavskyy9543]

Can you connect Type-C cable to the DJI O3 air unit when the module is mounted in this way?

[@TRONCATFPV]

unfortunately you can't plug in the USB-C with it the way I have it mounted, to transfer footage I remove the SD card 👍

[@christopherbuga3608]

What is the best dji fpv camera for low light

[@LoveeSkatee]

Would love a specific video about this build! 🤩

[@Selectaaaahhhhhhh]

Would you say that the 03 is a viable option for commercial applications in your opinion?

[@domnicdrakon]

are you using the goggles integra? i want to get into the DJI system but idk what to get

[@SteveO4478]

I’ve been using the 03 for work it is good enough till I can afford a naked 11. Looking forward to your 11 settings!

[@DudeMaybeSomeday]

Do you enjoy this drone setup or your Pavo25 build more for shooting real estate?

[@TRONCATFPV]

my Pavo25 is still my daily real estate FPV quad. This is my backup 2.5" cinewhoop 👍

[@DudeMaybeSomeday]

@@TRONCATFPV Gotcha.. Also, you might get a kick out of this.. Literally sitting here watching your gear breakdown video when I get a notification that you have replied to my comment 🤙🏻I appreciate your content and your help. I'll probably be hitting you up soon for the carbon antenna upgrade mount STL. Enjoy your weekend!

[@verbalamuse]

Hello, fellow pilot thanks for sharing your opinion on two cameras but I have a problem with holding that o3 antenna. Can you share your 3d prints for the antenna mount?

[@TRONCATFPV]

Although this mount is for the cinelog25, it works quite well on the QAV with no modifications: www.thingiverse.com/thing:5867038

[@gimbalair]

Perfect timing, i was debating whether to spend another £500 on a naked 11. I will hold back and just pull some stuff back in edit, I have been pleased with the results so far.

[@WassimJelassi]

impressed by the O3 for real. The go pro is flickering

[@weslisahum]

So for indoor real estate I don't need any extra additional camera on top of my Avata right?

[@L.G.]

Great video! Thanks for sharing your knowledge. If you wanted to get more flight time out of this build, what would you do. Simply add a larger capacity battery or would you go with different motors as well?

[@TRONCATFPV]

on this specific build I would most likely just use a larger mah battery. with the 550mah without a GoPro I get about 5 minutes. with a 750 or 850 I could probably get 7 or more.

[@quantum_m3chan1c]

Can you recommend any other batteries than this Ovonic 550mah 6s? It seems they're out of stock everywhere :(. Considering this "Tattu R-Line Version 1.0 550mAh 6S 95C LiPo Battery - XT30 " but I'll have to swap my connector to an XT30. I put an XT60 on this 2.5" 6s quad thinking I could use my same batteries from my cinebot30 (1100mah).

[@Michi-nw3md]

Cool Video ! Can you please make more build-Videos. I love them !

[@TRONCATFPV]

going to have a build video coming out within the next month or so, keep an eye out!

[@bluewhalefpv]

good bro! Can I get the qav 2.5inch antenna mount file?

[@its_Savian]

awesome work, can you please make a comparison on the dji o3 air unit 4k 120fps vs the gopro 11 4k 120fps please 🙏

[@TRONCATFPV]

I like this idea. Typically I prefer 60 or 30fps since you get better exposure indoors. 120fps comparison would be good for some outdoor slomo shots 👍

[@its_Savian]

@@TRONCATFPV yes please

[@YorkyPoo_UAV]

Ah I'm downloading that printables file now for the camera mount. Are those screws for the O3 1.5m?

[@FreshPanda97]

thanks mate! 1. how big is the difference between the QAV Pro 2.5" O3 frame and for example the pavlo25? In terms of weight, and also in terms of frame flight characteristic (because of the more open design i am very curions if you feel a big or if any which speciffic difference) 2. why you fly the patch LHCP antennas on it with the stock o3 antenna, normally you have better range with the stock goggles 2 antennas on the o3 3. did you managed to fix the whopples on the Hero11 with that frame? I still love my cinelog25 because of the way they isolated the Cams... 4. do your goggles 2 also with your vista builds or do you switch between goggles 2 and v2? I am still not sure if I should switch i have both, but somehow i like the range of 2 better but the fittment of the v2 more....5. I fly 4S 650mah on my Cinelog25 (have two as a backup)...whats the biggest difference in reelestate filminig with 6s? Better Throttle controll possible?

[@djiadventures1494]

Hi, which lipos are best for 4s 25” cinewhoop with naked gopro attached to it to get 4-6 minutes of slow flight?

[@eyesupdroneservices]

Another great and informative video; thank you! What angle do you run your FPV cam at?

[@fearlessflyersfpv420]

it is at 0 degrees, good for really slow flying (and flying backwards :))

[@dukevah]

Great video. Not sure it is my screen or the video but I can see some micro vibration for Gorpo when it is zoomed. I hope it is not what you got out of the stabilisation process.

[@yohalmocoto4604]

I noticed that too. i think the gopro might need to be soft mounted in order to get rid of the micro vibrations. Soft mounted on gummy mounts. Maybe @troncatfpv can see what caused the micro vibrations?

[@dukevah]

@@yohalmocoto4604 I was actually thinking it shouldn't be that much floaty. I might be wrong!

[@TRONCATFPV]

Those micro vibrations are completely removed when the GoPro is soft mounted like Yohalmo Coto mentioned. On my Pavo25 build I designed a 3D print specifically to combat this and am in the middle of designing one for the QAV 2.5" frame. For this test I wanted to keep the two as consistent as possible and kept them both hard mounted to the drone. The O3 gyro appears to handle micro vibrations a bit better than GoPro!

[@yohalmocoto4604]

@@TRONCATFPV This is very interesting. I wonder if there is any way to color/exposure match in post to make it look super identical. I feel like if that is the case with the O3 gyro....people might be able to get away with that footage rather than going naked. its looks surprisingly good!

[@The_GreenMachine]

i think if you get the gopro mounted on some shock absorbers that footage would be way better. it had so much jitter in the footage, yet was much sharper.

[@TRONCATFPV]

Agreed 100% I prefer drones that have some sort of dampening for GoPro/O3 Since filming this video I’ve been able to tune out those micro vibrations but would still love to see a dampened mount for this drone

[@The_GreenMachine]

@@TRONCATFPV can you print your own from TPU? basically an adapter plate under where the gopro attaches to

[@YorkyPoo_UAV]

What are you doing for a tune. I've tried several things and I keep getting jello in the O3 cam

[@Justin-Hugge]

What is the mount to hold the naked gopro? I can't find a mount for it anywhere!

[@lucarednic7658]

Hello It am trying to do the same thing as you (real estate tours) but in my country. Can I ask you for tips and tricks for doing this? Thank you very much!! :)

[@smsg83]

No capacitor for the naked GoPro? Maybe I should remove mine because it looks weird and takes some space.

[@Assalamu_alykum]

So, how it stabilized?

[@johnnycovington1580]

Subscribed! Do you have any videos on what “Actual” rates you like to fly for these types of tours and why?

[@big-smoke-rc]

What is the point in using a quad for this shot? Virtually all of it apart from the start could be reproduced by walking around with a gimbal camera?

[@TRONCATFPV]

The benefit is one continuous shot throughout the entire property. It seamlessly attaches interior and exterior spaces. Feel free to check out some of our single-take real estate FPV videos: kzbin.info/door/fpYXS61D5tSvZ3ACeNheXQ

[@soulfirefpv]

nice job dude! where can I find the gopro adapter tothe GEPRC naked mount for print? thanks for share!

[@soulfirefpv]

found it in other of your videos, thanks again!

[@sten6537]

Could you share your Gopro 11 naked indoor settings with us?

[@IDESERTSTORM]

Looking to build one of these was the camera mount required? it doesn't look like Luminier makes one currently and I'd have to find someone to 3d print it.

[@YorkyPoo_UAV]

I use that frame and love it. I can hear you are running blue jay

[@TRONCATFPV]

I've been loving the QAV frame. Especially with the O3 on it now. Once I get a dampened GP mount designed for it i'm sure i'll be using it more than my other cinewhoop!

[@bennie1198]

@@TRONCATFPV What about this frame do you like more? I was looking to build the QAV-PRO Mini but I know the Pavo25 frame is $120 cheaper. Do you think it is worth it?

[@YorkyPoo_UAV]

@@bennie1198 the Qav-pro 2.5" is $80 USD. I picked it because of the foam snap on bumpers and quick detached rear camera mount. To save money of go with a Hurricane 2.5" or the FPV GOD mode frame

[@NickCohoon]

QAV-Pro vs your go to BetaFPV Pavo25?

[@CoffeeFlying]

the video at 0:30 is not with the gopro 11 ????? if so what are your settings

[@TRONCATFPV]

That shot was filmed with an Air 2s

[@LeonSTE]

Hello there again! I'm also planning to build the same drone and I'll definitely refer to the links you've provided. However, before I begin, I have a question. Could you please explain how you soldered the O3 air unit onto the Aikon board? Which cable did you use and is that provided? I'm really looking forward to building this drone and I hope it will fly successfully even if it's my first attempt.

[@TRONCATFPV]

You can use the cable that comes with the O3 unit. Since I'm using crossfire on this build the SBUS and GND tabs on the O3 are unused. On the left side of the aikon F7 there are 10v, GND, T3, R3 pads that I have my O3 hooked up to.

[@LeonSTE]

@@TRONCATFPV thanks!! I ordered everything with youre affiliate links :)

[@gimbalair]

Have you shot in any dark environments, like a gym or a theatre? I have the GP11 and 03 on my cinelog30 and find the performance of both a real struggle when editing.

[@noamperetz5805]

I thought your new betafpv drone that you built was ment to hold a full size gopro.. I assume it was to heavy?

[@TRONCATFPV]

Even though that drone can technically fly with a full sized GoPro, I never do since it cuts flight time in half. These 2.5" cinewhoops I always fly with a naked GoPro on board.

[@bkjeep]

Shutter auto, iso auto in settings?

[@shaunvaughn3323]

Nice flying. For indoor real estate do you use angle or acro?

[@TRONCATFPV]

Acro always 🤙

[@WegaFPV]

what is the weight difference between this drone and the pavo25 build ?

[@sheepfpv2780]

Love the look of O3 and this build! Would love to mount o3 in mine to with this print, did you use tpu or something else to print it?

[@TRONCATFPV]

TPU to prevent any vibrations 👍

[@GusCanales]

what is the total weight of this setup?

[@andyvasquez4392]

I love watching your videos and want to do a build like the pavo 2.5 but on a lumenier 2.5 pro frame. Just wanted to ask what are u using on this deone with the 03unit?

[@youmasontube]

Awesome video, learning so much from your channel 🙏 Curious to know if you fix the shutter or the ISO for these shoots? Thank you

[@serge1201]

I want to upgrade from a caddx vista to O3 in this same frame, did you modify the mounting holes on the bottom plate or was it direct fit?

[@TRONCATFPV]

On this build I used a 3D print for the O3 on this frame: www.printables.com/model/391819-lumenier-qav-pro-micro-whoop-dji-o3-air-unit

[@LoveeSkatee]

Can you recommend the Lumenier QAV-PRO 2.5 frame for filmmaking or is there a better option at the moment for sub 250 with naked gopro?

[@TRONCATFPV]

I have been using the QAV 2.5" frame as my daily for commercial projects for 5 months or so and LOVE it. Going to have a sub250 build w/nakedGP coming out in the next month or so 😉

[@jpov0409]

Nice comparison! Where did your soft mount for the dji 03 camera on the Cinequad come from? I don't have a 3d printer but would like one of those mounts!

[@TRONCATFPV]

Both cameras are hard mounted to the drone. The mount I used for the O3 camera was this one: bit.ly/3M7gZPN Typically I prefer to dampen the GoPro mount but both in this video are hard mounted 🤙

[@jpov0409]

@@TRONCATFPV Thanks! That mount in the link is what I was looking for. Maybe I used the wrong terminology. I've been considering anything mounted with tpu as "soft mounted"

[@QSpeedRacer]

Gopro seems to have more details in the dark areas and then u edit after. But some reason gopro seemed to be getting vibrations.

[@mokshpatel6986]

Great , looks like GoPro takes make low shouuter speed that can caused jittery footage , isn't ?

[@HuntAndFishExchange]

So is the Pavo 25 your main drone that you do all your cinematic real estate shoots with? Also will the Pavo 25 accept the 03 air unit and camera?

[@TRONCATFPV]

The pavo25 build is my main drone for real estate FPV projects. There are adapters for the Pavo25 frame that will fit the O3 air unit camera. I personally havent tested them out but i'm sure they work!

[@DopTikhonov]

Nice O3 cam support! Where did you get that?)

[@califpv]

getting dust and stuff in front of the lens is the only thing I don't like about gep's 11 case. I broke out the glass now I can wipe the lens...

[@adilchopdar7746]

What controller and goggles you used ??

[@vanlifefpv6340]

A lot of vibrations seen on the GoPro footage. Maybe it needs a dampened mount?

[@TRONCATFPV]

Yes, See pinned comment

[@sammyb3104]

Love your videos! Building my first drone this weekend, I'm super stoked

[@WaynePilot]

Very good post edit for easy comparison. Thanks for the sharing!

[@MrCoffis]

You seem to be having some oscillation going on with the GoPro. Its jittery. Are you using anything to dampen the vibrations?

[@TRONCATFPV]

Both cameras are hard mounted to the drone, usually I do prefer to soft mount the GoPro.

[@ItsRen_FPV]

hey very nice video as always , i am very surprise by the o3 of your video , i get a lot of jello with my footage on my o3 , maybe my tune ... what is the best way to tune the pid on a quavpro like yours ? and could you share your settings for the gyroflow pls ??

[@flyingeyefpv]

In terms of delivering a final product, would you consider the o3 up to your professional standards or will you continue to use the naked gopro setup?

[@TRONCATFPV]

Persinally between the GP11 and O3 I prefer the naked GoPro

[@BartManDude]

Thank you for this video, excellent quality. I'm curious, why did you decide to go with the pavo25 build over this qav-pro one?

[@TRONCATFPV]

The more I use it, the more I’m actually starting to prefer the QAV

[@BartManDude]

@@TRONCATFPV Very interesting. I've been on the fence between these two for a few weeks now. My buddy built your pavo25, and loves it, but it's so loud. I'm more enamored with the QAV, so was thinking maybe building that one. The only reason I hesitated is because I kept wondering what made you switch. Now I'm just going to build it and see if I like it LOL. Thanks man, your videos inspire me and I appreciate your style, insights and sharing your experience. 👍

[@PhillyDroneLife]

Thx buddy . Mikey

[@paul_london]

What goggles do you use?

[@TRONCATFPV]

I have the DJI Goggles 2 with X-Air MKII Antennas 👍

[@paul_london]

@@TRONCATFPV thanks! Love your videos brother!

[@SiOgie]

A superb comparison! *Thumbsup! I'm wondering if you fly ANGLE or AIR mode indoor? I want to try it as well. Cheers!

[@dronemagicnl4986]

Never air mode indoors, there’s no wind so you don’t need it while airmode can cause the drone getting sucked into wall when flying to close

[@TRONCATFPV]

I always fly in acro 👍

[@SiOgie]

@@TRONCATFPV awesome throttle management then! 🙏🏻

[@evFPV]

The amount of jellow the GP footage has is insane

[@TRONCATFPV]

Yea I've always gotten really noticeable micro vibrations in GoPros when they are hard mounted. Since the O3 is hard mounted, I wanted to keep it consistent with the GP11 and hard mounted that as well. Normally like to run dampened mounts with GoPros specifically to combat this

[@G1NJO]

so u switched to qay-cine 2,5 ?

[@TRONCATFPV]

For residential real estate I still prefer the Pavo25 build. I have been using this QAV 2.5 build more and more for bigger projects and larger real estate. If I end up making the switch to this one, I’ll make a build video for you guys 🤙

[@G1NJO]

@@TRONCATFPV thank u my friend

[@sheepfpv2780]

Is this the same tune as the Pavo25 build you did, or do you have a different tune for this one?

[@cuneoism]

Can you stabalize the Air unit footage?

[@TRONCATFPV]

Yes you can stabilize O3 footage in gyroflow

[@maxartfpvperufilmacionesya5360]

What frame... are u using in this flight

[@TRONCATFPV]

All the details on the drone are included at the end of the video. This drone is on the QAV pro 2.5" Cinewhoop frame: bit.ly/3U0MTz5

[@RichardGeresPT]

Very precise flying! Impressive! The image quality is very close, the colors just seem more vivid on the GoPro. I wonder if you can make up for that with color grading. The GoPro does have better slow motion settings than the O3 unit, if you need that feature.

[@jamesmorris6933]

Hey great video love all the excellent information! Just wondering what rates you use and whether you use a throttle curve or a motor output limit? Thanks

[@TRONCATFPV]

I Go over rates in my 2.5" drone build video 👌

[@jamesmorris6933]

@@TRONCATFPV thanks appreciate it! Going to be doing some flights indoors for music that I work on

[@macaedroneclips]

I really enjoy watching your videos. What model frame did you use?

[@TRONCATFPV]

This is on the QAV pro 2.5" frame Details on the drone are at the end of the video 👍

[@nzii3]

What cinewhoop frame were you using with the o3?

[@TRONCATFPV]

This is on the QAV Pro 2.5" frame. All details on the drone build itself are at the end of the video 👍

[@nzii3]

@@TRONCATFPV Thanks :)

[@thomask.626]

Sick video 🔥🔥🔥🔥🔥👌🏻🙏🏻🙏🏻 helped a lot will wait with the Go pro never noticed the vibration in other videos

[@efelton2699]

The need for a second camera is history.

[@mjodr]

That's what I was thinking the whole time. I knew it would get to this point.

[@aib666]

Which drone is that? custom build?

[@TRONCATFPV]

yessir, all details on the build are at the end of the video 👍

[@krisgleave]

I followed your series and the previous build and have some questions please. I want to be able to fly with O3 but also carry a GoPro Mini 11. I am insure with what setup to go with and frame now I’ve seen this. What would you recommend? Even using the older build you did but with parts being tricky to acquire would I work similar with the speedybee f7 AIO and some alternative motors?