10 Quick Tech Tips- Harley Comfort for LOW & NO $$

[@thejerseyj9422]

I like that tank lift idea not only for the heat reduction, but I can get to my chrome heads and clean them easier.

[@DKCustomProducts]

Yep, cools em down a bit, reduces buffeting a bit and shows of the chrome and makes it easier to clean also! Thanks for the comment!

[@114bob]

Don't do it on tiny sportster tanks without moving fuel tap! I did it 2inches and lost 20 miles range, had to stop at bars😂

[@geneedwards2910]

I have removed left side heat shield, added tank lift, air wing deflector which also helped my head buffeting, and floorboard extensions which has really helped riding comfort. Tomorrow installing 606 air cleaner and EBS and VIED. Thanks for all your videos and advice.

[@DKCustomProducts]

Thanks for sharing. We appreciate your business, and it is good to hear the parts have enhanced your riding experience! 👍

[@Evil_Empire42]

Will removing the right side heat shield by your leg, and keeping the left side on, produce the same results?

[@lancek3387]

@@Evil_Empire42 no. You will be blowing more hot air behind your right leg, along with the already hotter right side air. Putting heat to heat only produces more heat.

[@DKCustomProducts]

@@Evil_Empire42 Similar, but not the same. There is more heat on the right side, so it will not feel as cool to the rider. Also there are more obstructions on the right, so the air will not flow around the rear cylinder and out as well with left in place and the right removed.

[@darkhorse2reign]

I enjoyed listening to bike tech talk even though I'm a Goldwing guy, I love the classic looks on the Harley. Ride safe fellas.

[@DKCustomProducts]

Thank you! You too! 👍

[@gordonwrichert8240]

NOW USING THE AMS OIL IN MY CVO THE TRANSMISSION NOW IT IS QUIET AND SHIFTS LIKE BUTTER NO MORE HARD TO FIND NEUTRAL ALSO USING IT IN THE MOTOR AND PRIMARY HAVING GOOD RESULTS SO FAR

[@DKCustomProducts]

Awesome! Glad you have found an oil that works well for you! Thank you for commenting! 👍 MB

[@talltimbot]

My 1978 Low Rider has been very cool since parking it in my house decades ago. My flat twin does very well in hot weather

[@DKCustomProducts]

Thanks for sharing! 👍

[@MAGOLD1120]

While i haven't done any mods to bring the overall heat temps down, I did open the right side vent. It seemed to lower temps slightly, but open it relieved the heat felt on the inside of the leg and foot.

[@DKCustomProducts]

You can see a written report on WHY and How to Cool Down Your Tc & M8 at this link - www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm and www.dkcustomproducts.com/why-how-to-cool-down-your-twin-cam-engine-part-ii-dk-cl-tc-dn-2.htm Please feel free to reach out with any questions; [e-mail] 662-252-8828 Thank you for commenting! MB

[@Jimmy_Jim_Jim_1234]

For my 2010 Superglide C i did a stage 1 with a good tune, as well as a Jagg side mount oil cooler. A HUGE improvement.

[@DKCustomProducts]

Good deal! 👍😎👍

[@Jimmy_Jim_Jim_1234]

@@DKCustomProducts i just ordered a cleanable oil filter with 5 o-rings from you. Its on its way! I had one for an d R1 track only and it was good.

[@JerryNelson-jb4fo]

Just added the air deflector wings and a 1.5 inch tank lift to my 2015 FLHTKL and while I don't have historical data on the Temps in the short time I've noticed that I don't feel the heat like I have before. When I have felt heat off engine due to slow speed and changing direction it quickly disapaits when increasing speed and/or changing travel direction. So I highly recommend. Dk Customs has impressed me with their customer service as well as their products. Tank lift,Cooling defector wings and the 606 AC with Transformer EBS. Order wrong size Thunder Tourque Inserts and DK has gone above and beyond by sending correct size. Just can't beat their customer service.

[@DKCustomProducts]

Man, thank you for the comment, and your business. We appreciate it! Good to hear that you are getting your bike dialed in and are experiencing the benefits of the parts. 👍😎👍

[@samslade739]

I totally agree with these tips and have done most of them. However, Pipe wrap? A friend wrapped the pipes on his Shovel and it did keep the heat in but the pipes got so hot that they basically disintegrated.

[@DKCustomProducts]

On the product page it says "DEI does NOT recommend wrapping exhausts made of titanium. The alloys used in the production of titanium exhaust systems tend to be thin and are designed to dissipate heat quickly. Wrapping any titanium exhaust pipe, regardless of brand, can hold in too much heat, and make the titanium alloy turn brittle and prone to premature cracking." If his exhaust was Titanium it is possible that was the issue. Kevin has had exhaust wrap on his Sportster exhaust for 10+ years and they have not rusted or gotten brittle. Here is a video about good exhaust wrap- kzbin.info/www/bejne/j5uagauQjayboZY Thanks for commenting! MB

[@phillipmckeownakalucifer.6689]

Got the jims fan...... friggn awesome.... buy it yall. I had epic failures with alot of things. But this fan equaled the score

[@DKCustomProducts]

Good to hear you are liking it! 👍 Thanks for the comment, and we appreciate your business. Enjoy the Ride!!!

[@billcarson1966]

Number 12 - Point your bike north and ride really, really fast for a long, long time. Not free per se, but lots and lots of fun!

[@DKCustomProducts]

North or to higher elevation! Yep, a ton of fun!

[@tomrinde4487]

Don't cruse city streets and bolavards

[@qthebikeahaulic]

Here in Nevada I do just the opposite with the thigh wind deflectors,.Above 80 degrees I put them back on so my legs don't cook. I tried just taking the left hand side off and about roasted my leg above 80 degrees. The floorboard bump outs help out way more than some might think,that is a Great tip. Plus they are needed with cooling fans so my leg sits more level/straight.

[@DKCustomProducts]

Are you wearing jeans or shorts? If jeans, then my guess is that the engine is just too hot overall and needs some cooling down. Here is a series of videos that you may find interesting/useful- kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C

[@Zukgod1]

Interesting on the coil relocate. Mine is behind the plate under the seat. 15 Glide. Pretty sure that is not blocking any air flow to that rear cyl. That said, the DK tank lift and airfoils are awesome on my bike.

[@DKCustomProducts]

Interesting! Thanks for the info and for commenting! Glad you are liking the tank lift. Thank you for your business! 😎

[@Dirk1961-l7y]

I have a 103 police version Electra with deflectors. But…..the previous owner let mount a blower behind the oilcooler….nice!

[@GusMoore-j7r]

Love you brothers for real, always great tips, honest experience talk… I dig it. Thanks for all you do.

[@DKCustomProducts]

Appreciate that, thank you! KP

[@cryptowade3194]

I added the defector wings, new headers (no cats) ultra cool oil cooler on my 2020 trike and I just rode it hard for an hour and my oil temp was 190 on a stage 2 build 🙌 Also I have the DK catch can

[@DKCustomProducts]

Very cool! Glad the products are doing their jobs! Thank you for your support and for commenting! 👍😎👍

[@joehansen4889]

I just installed the transformer catch can. And the 828 air filter. Looks fantastic!

[@DKCustomProducts]

Very cool. Thanks for the comment. 👍😎👍 We appreciate your business, and glad you are liking the parts.

[@joehansen4889]

@DKCustomProducts I was watching your video on the exhaust that you all put in your after market mufflers. Do you have how to install them video?

[@DKCustomProducts]

Yes, there are quite a few in this playlist- kzbin.info/aero/PLb3bvZgbH92-y9LGItkUD9O2fFo3-gtVl And here is one we did a few months back on a friends bike- kzbin.info/www/bejne/fJPWgXeQg85okNk

[@kpnomad7]

Kevin, I wrapped my bassani header tonight, but now read some techs saying the heat trapped in the header by wrap has molten effect on some headers and that most vendors will not warranty headers that have been wrapped!! Thank you for your replies to all our questions, reason I wanted to wrap is hot hot right foot/ankle with just shields!

[@DKCustomProducts]

If wrap will make a molten effect on headers, it could be one, or both, of these two reasons: 1. Engine is running too hot for it's own good (regardless of the wrap) 2. Cheaply made exhaust. There are more and more knock-offs coming out of Asia, some with really poor quality It is understandable that an exhaust MFG. will not warranty wrapped headers. They have not control over whether the bike will be put up with wet wrap, time after time. Done enough, it can result in rust and eventual failure. Here is a video where we talk about wrap, rain, washing, etc. kzbin.info/www/bejne/j5uagauQjayboZY Getting temps down to the ideal, for performance, heat reduction/comfort, engine longevity...here is a written report link and a video playlist link- www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C

[@kpnomad7]

Thank you Kevin,. I rode today and my leg was not on fire, and I assume bassani made header thinner then oem! But I am happy with your suggestions to cool hd bikes!! And if I notice , I'll adjust tongue insert angle! Thx again!

[@DKCustomProducts]

@@kpnomad7 Good deal on making it more comfortable. To reduce any chance of a problem, do not let it set up with wet exhaust too much. Of course, it can be impossible with rain sometime. But don't wash it and then park it.

[@edwardclark2947]

So glad you are teaching the proper way to ride. I've never thought riding your clutch at high rlms is wise. Just like driving a stick shift car...

[@DKCustomProducts]

Good to hear you're finding our videos useful/interesting. 👍

[@billflixtone6684]

I used my FP3 to add the first level of "decelpop" (there was no decel pop on my 107). The extra fuel on deceleration keeps the temp about 10 deg cooler.

[@DKCustomProducts]

Yes, many folks use that strategy of dumping extra fuel to get it cooled down a bit. Thank you for the add.

[@FeatheredDino]

If you wanna spend some money to cool your M8, and get some more power, a canned tune with FP3 cooled my bike significantly. I went in further and changed some of the AFR tables myself, dropping the highest AFR on the table from 14.41 down to 13.90, and changing closed loop AFR from 14.30 min/14.91 max, down to 14.10 max/13.80 min. Cooled my bike down even further.

[@DKCustomProducts]

A tuner is definitely a good way to cool down your bike, but this specific video is for Low to No cost ways to cool down your bike for bikers that can not afford a tuner, or want to try some less expensive ways first!

[@georgefraserjr1329]

My 04 ultra runs so hot in the summer that I don’t even want to ride it but I think one of,if not the biggest problem is the true duals with the pipe that comes off the rear jug and directly under my left leg,can’t tell you how many times I’ve burnt my leg on it but I have a 2 into 1 that I’m going to install and do the heat deflectors and hopefully that’ll help,my superglide runs so much cooler it’s not funny but it’s also not a long distance bike,thanks for the vids guys,gonna try some of your suggestions

[@DKCustomProducts]

Glad you like the video! The cooling deflector wings can certainly help push air to the heads and cool it down. If you haven't taken the CAT out of the exhaust, that can help with a lot of the felt heat. Also you may want to look at an exhaust wrap. That can also help on the felt heat from your exhaust. Here is a video about taking the CAT out of your exhaust that you may find useful - kzbin.info/www/bejne/oaSWanqtl5iBmqs Here is a video on the exhaust wrap that you may also find useful - kzbin.info/www/bejne/j5uagauQjayboZY Here is a full video list of why and how to cool down your bike - kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C Here is a written report that can also be helpful when choosing what items you would like to do to help reduce the heat with charts and heat reduction measurements - www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm Please feel free to contact us with any questions you might have; [e-mail] 662-252-8828 Thanks for commenting! MB

[@kevinrosebush2669]

I put a Vance and Hines exhaust on my nitester is awesome.

[@DKCustomProducts]

Good to hear you're enjoying your ride! 👍

[@fatboyrowing]

I got my first Harley in 1996. Now I know how those shovel head guys felt at that time. I’m now riding a 1998 springer and very few of these ideas apply to me…. however I think I’ll relocate my oil filter. Get it out from in front of my engine and put it out in the wind somewhere. They look cool remotely mounted and the act cool too

[@DKCustomProducts]

Good idea! Enjoy your ride! 👍 Oil filter relo link- www.dkcustomproducts.com/cnc-oil-filter-relocation-kit-sportster-dyna-softail-touring-dk-cnc-ofr-uni.htm

[@fatboyrowing]

@@DKCustomProducts that’s perfect!

[@DKCustomProducts]

@@fatboyrowing Good deal man, thanks for watching our videos! Ride safe!

[@haroldwiser2641]

All from DK Customs I have a hi-flow air cleaner, titanium heat wrap, floor board relocation, external breather system and TTI's. My bike is very comfortable to ride!

[@DKCustomProducts]

Very cool. We appreciate your business, and it is great to hear that you are enjoying the parts. 👍

[@larrypiazza4909]

I have a 2011Softail CVO 110 at one time it did run hot, 270 oil temp but now in Texas in August hottest month of year stop and go traffic 235 oil temp. I'm running Oil Bud 37 row cooler with a 313cfm fan on it that comes on at 190 degrees, Love Jugs fan system, External breather ,2 into 1 D&D fat cat and been Dyno tuned also a ribbed billet cover over my oil filter this really works about 8 to 10 degrees on oil temp Harley sold these at one time for $50.00.

[@DKCustomProducts]

Great to hear you have your heat under control. Thank you for your comment.

[@vikingkombat9389]

Exhaust wraps help a lot keeping the heat of you

[@DKCustomProducts]

Yes it really does decrease the felt heat! Thanks for commenting

[@evetsegap]

Thanks for your time on these videos.

[@DKCustomProducts]

Glad that you liked it! Thank you for commenting! MB

[@KirkDavis1966]

Wondering if you have a video on FLASHING a TC103 ECM when replacing a body module.

[@DKCustomProducts]

We do not. Never had to do that, so no opportunity to video it. Thanks for checking.

[@timconnors550]

Thanks Brothers you've taught me some new strategies for cooler operation. Respect

[@DKCustomProducts]

Thank you for the good words. Glad you found the video useful. 👍

[@stevesyncox9893]

Northern Canada here, we get 40°C up here in summer...105°F. So the fans are in my future.

[@DKCustomProducts]

That will definitely help! 👍

[@micahruddell74]

The biggest difference I have felt was to direct the air vents in my lowers at the engine as opposed to open them wide open. I don’t have a way of checking engine temperature but it definitely has helped the heat I feel on my legs.

[@DKCustomProducts]

Good tip! Thank you for the comment. 👍

[@pauldineno6919]

I removed the vents completely

[@johnbutler8026]

I have a 21 Road Glide with the the lower fairing spoiler, HD oil cooler fan, DK catch can w/ external breather, and mid frame deflectors, which I will remove the left side. I also have the Dakota gauges where I can monitor oil temp and head temp. The head temp at its hottest was 333 deg. while the oil temp was 175 deg. This was on a 75-80 day. What are your thoughts I'm not sure if I want to raise the tank. Thanks.

[@DKCustomProducts]

Thanks for your business, we appreciate it. When you say the head temp at its hottest was 333 F. What was this measured with? The Power Vision ET gauge is what gets the direct temp read out from the embedded OEM heat sensor. There is a read out on the PV of Cylinder Head Temp, this is not an accurate reading of anything. It is a computed number that is not stable or reliable. I do know that the oil temp read out on the Dakota Digital has not been accurate the few times we have tested it. We have also had Customers report to us that it is not accurate. The way you can test your oil temp accuracy is to measure it at the dipstick hole...use a oven thermometer, and see if the reading is close to what the DD is giving you. Here is a video that I believe will be very useful in explaining the different readings the ECM uses- kzbin.info/www/bejne/ZqfFhZ6Iq6uUbpI One other thing to note, it takes the oil far longer to heat up than the OEM heat sensor. To get an accurate reading, you will want to ride at a good clip (50 mph or more) for close to 45 minutes for the engine to fully warm up and get an accurate read of your fully warmed up oil. If, after riding for 45 minutes, you are able to verify that the oil (at the dipstick) is 200-230 F and that the heat sensor in the cylinder head is over 300 F, then you will know that your oil cooler is working very well, but that not enough air is getting to the engine to keep it down in the optimum temp range (which for your M8 is between 230-260 F), and that you will benefit from increased air flow to the engine.

[@boilerfreak77]

RUN GOOD OIL!!!!!! most OIL goes shish around 225-250 ... mobil1 vtwin is good to 300... I have run my s&s engine for 17yrs at high rpms in south florida... breaking down the oil runs engine heat up. With the mobil1 she never breaks down. I change oil twice a year and it always looks good. Not even close to being burned up... my bike is chopped as well and hangs out in the air all day. But firm believer in high temp synthetic oils. And mobil1 has never let me down. 17yrs 100mph..

[@DKCustomProducts]

Thank you for sharing your experience. 👍

[@antbonyziemiak208]

If you install Jim’s fan, won’t that blow hot air towards the air cleaner, exactly what you don’t want? And by the way, why does Jim’s fan have to look like AMF air cleaner ???

[@DKCustomProducts]

Yes, some of the air blown over the engine will be in the pathway of the air cleaner, especially at a standstill and going up to about 20 mph. It still produces a net effect of much lower engine temperature and a corresponding increase in performance. Regarding the design...we did not design it, and have no influence on the design, nor do we know why they designed it that way. Thank you for commenting! MB

[@UncleFjester]

2011 StreetGlide, Open flow Air cleaner, Chrome "Umbrella" Baffle, Floor board extenders

[@DKCustomProducts]

Glad you're enjoying your ride!

[@jackthebagger7589]

Good tips , #1 I removed both , they cook your legs in stop and go , #2 I used 1 1/2" flat straps in the front and a one inch tall socket in the rear , fuel gauge spot on and runs cooler , #5 I pulled the head pipe and drilled out with a butterfly .. Floorboards are done on the cheep to with pieces of pipe cut to 1" and used as a spacer and longer bolts , this is also a much more comfortable riding position .. external breathers are obvious .. I always wanted an Ultra for the lowers , my '88 Tour Glide was last year before the TGU , so never got one of those , as soon as the RGU hit the floor I got one , and 1) the vents would not stay open and 2) I hated them , they have been hanging in the shop since the second month I got this bike .. I have a set of Harley softs that are well over 35 years old , I use them if I need lowers

[@DKCustomProducts]

Glad you enjoyed. Thank you for the comment.

[@wasupfool5692]

My 2010 Fatboy is all stock except for pipes and breather, and it runs that hot if I get stuck at a set of lights for 3 or 4 minutes I have to get off stand beside the bike.

[@DKCustomProducts]

Sounds like the engine is just too hot overall and needs some cooling down. Here is a series of videos that you may find interesting/useful- kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C Thanks for commenting!

[@michaelblew6019]

Adding rear cyclinder air scope on older bikes helps also,if you can find them,,bolts to rear cyclinder head bolt

[@DKCustomProducts]

Yeah, the shovels used to run those pretty regular. 👍

[@mikelivingston6157]

What if I need the fork fangs to keep the buffeting down on my helmet? Without them my head shakes so bad I can’t see

[@DKCustomProducts]

On average your engine will run 25 F hotter with the fangs. If your temps are not getting too hot with the fangs, that is great. If you engine temp is too hot, you may want to look at other solutions to reducing buffeting... Cooling Deflector Wings Windshield Helmet Foot position etc. KP

[@levialston1496]

I bought a love jug that works great only use it when I'm in traffic

[@DKCustomProducts]

Nice. If you run them while riding you will get even more benefit. Rear cylinder runs hotter going down the interstate than in stop n go traffic. We did a test on that and published the numbers in this video- kzbin.info/www/bejne/sJ6tnqOanKeAaaM

[@lancek3387]

I have done every mod to my 09 Ultra that can be done on the cheap.....tank lift, air deflector wings, left side air shield removal, factory air box modification (complete removal of any nonessential plastic), external breather mod....and this stuff WORKS! Alot less felt heat on me, and that means a much more efficiently cooled motor. I don't even feel the heat through the seat like I used to....that should say something about dissipating engine heat. My only mod left to do is the VIED for better fuel/air ratio mixture.

[@DKCustomProducts]

Thanks for watching and commenting. Good work, and we appreciate your business. 👍

[@lancek3387]

@@DKCustomProducts You guys have outstanding products and same level advice/ideas! 👏 👏👏 Without the mods, I would be riding much less comfortably and with much more engine wear and tear from heat related problems.

[@DKCustomProducts]

@@lancek3387 Man, that is great to hear. From Day one our goal has been to enhance folks riding experience. Thank you for the feedback.

[@steves2837]

One way I’ve found in addition is to add a tuner and lower the AFR. A little more fuel sure cooled down my twin cam.

[@DKCustomProducts]

Yes, thank you for the comment. Typically one will see a 10-15* drop when going from the OEM tune to a good tune on a Twin Cam. Unfortunately it is not a low cost/no cost mod. However, it is a very important mod on a Twin Cam.

[@doug3805]

I use Valvoline VR1 in my 93 Harley Heritage Evo. I starting using it from recommendation from others that had the old Evo Big Twin.

[@DKCustomProducts]

That is a good oil. Have you seen this fun video we made about oil? You can see it at this link- kzbin.info/www/bejne/mH-rmIGKndekh9E

[@PAULY-P]

Check out Quick Silver synthetic oil. Can usually get a gallon for around $30. The charts show it's better than Amsoil, Mobile One, etc. Definitely cools the bike down a notch.

[@DKCustomProducts]

@@PAULY-P Thanks for the info. You may like this video and comment in it. kzbin.info/www/bejne/mH-rmIGKndekh9E

[@jimmiewilson1744]

Love you guys. Talked to Dwayne today and and ordered a Transformer breather system for my 2022 Road King

[@DKCustomProducts]

Thanks man. Appreciate your business, and I believe you will be well pleased with that. 👍😎👍

[@joelstrickland8890]

If I remove the plastic on the back the of the air cleaner on a 2020 RK with a 107 will I have to get it retuned?

[@DKCustomProducts]

You can change your Intake on your 2020 Road King and will not need a re-tune. Here is a video on the subject that you may find useful/interesting - kzbin.info/www/bejne/l4i6XqGqbJKZsKM Please feel free contact us with any questions; [e-mail] 662-252-8828 Thank you for commenting! MB

[@joelstrickland8890]

Great, thank you for the excellent, informative videos.

[@DKCustomProducts]

Glad you are finding the videos informative! Thank you for commenting! 👍 MB

[@bajarvcouple]

Thanks for combining all those free and low cost cooling tips.

[@DKCustomProducts]

Thank you! Appreciate the comment.

[@thomaskirkpatrick4031]

I had a 2003 Fat boy it was pretty much stock. That dam thing was uncomfortably hot. I switched to full synthetic oil, it made a big difference.

[@DKCustomProducts]

No doubt synthetic oil will result in less friction with is less heat. Here is a link to a playlist you may find interesting- kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C

[@findyourinnertube124]

Having both of those heat deflectors has made a big difference when stuck in traffic. Before I was burning my 'nads to a crisp. That's why I bought them. I would not remove one.

[@DKCustomProducts]

Thank you for your business! I am so glad you like the products! Thanks for commenting!

[@ericjames7680]

I need your help before I buy my next bike. I like the Street Glide and want to buy the ST model. When I do my research on them so many people comment on how bad the wind buffeting is and the best way is to install the fork fangs. But here on this video you say to remove them when the outside temp is 70 and over. Why don't you recommend to remove lowers too, would they also block air like the fork fangs? Can I leave them on and install a oil cooler fan to help things out and not get it too hot? I am in California and can not install any tuner to help out and the FL-ViED Fuel Enrichment for Harley EFI Plug-n-Play you sell are not available for the newer M8. When I ask others about the Street Glide buffeting some say to just get a Road Glide or to install the fork fangs. I would not be running lowers or the wind baffle, just the fangs. If the fork fangs and baffle raise the temp when hot outside by 20 degrees or so, will or can a oil cooler fan lower it back down 20 degrees or so with just the fangs? Will your cooling wings still work with the fangs installed to help things out? Thank You!!

[@DKCustomProducts]

Everybody experiences buffeting differently. So many variables: How tall Slouch or sitting up straight How tall are the handlebars Backrest or not Helmet Foot placement and much more. I would recommend riding a Street Glide and seeing if buffeting is even an issue for you. One of the biggest ways, for many who experience buffeting, to reduce it is to get a recurve windshield. Lowers do not block air flowing to the engine like the fangs do. Lower push air onto the engine in two ways. 1. They are rounded, with the inside half directing air onto the engine 2. They have vents that can be opened to direct air past the engine Say your engine is running at 270* and you put fangs on, that bumps it up to 290*, then you put an oil cooler on, that will drop oil temps by about 20* and engine temps by about 10*, so now your engine temp is 280*. Whereas, if you start at 270* and do an oil cooler (-10* ET), Cooling Deflector Wings (-10* ET), and tank lift (-10* ET), you are now down to 240* ET, a full 50* less than adding fangs, and 40* less than fangs and an oil cooler. Yes, CDW's will work in conjunction with fangs. A tank lift and cooling deflector wings do about 70% as much good at reducing buffeting (for those that experience it) as the fangs. BUT, the benefit of the CDW and Lift is that they also cool the engine. You can see a list of cooling components, including the CDW and Tank Lift at this link- www.dkcustomproducts.com/cooling-components-c661-191.htm Always feel free to call or email with any questions. 662-252-8828 [e-mail]

[@ericjames7680]

@@DKCustomProducts Thank you for the help. I am always told to install fangs to get rid of the buffeting. Is there a recipe that will work for cooling that include the installed fangs? I would be installing fangs, replacing the stock oil cooler with the electric fan Harley version like the police bikes come with and doing the wing deflectors you have, would this be OK and reduce the heat enough or are the fangs as you say going to reduce so much wind even with your wind deflectors I should not run them?

[@DKCustomProducts]

@@ericjames7680 There are many things you can do to cool it down...even with the fangs. It is just that you are starting in the hole by 20* with the fangs. I would do a small tank lift, 1" or 1.5", and the Cooling Deflector Wings. They will still help, even with the fangs installed. I would get a better oil cooler, the one at the link below will do better than the HD version. www.dkcustomproducts.com/lowmount-fan-assisted-oil-cooler-system-harley-touring-models-dk-j-751-fp2400.htm If you are still running to hot after that, then go thru the list at the link below, doing one thing at a time until you get your temps down to a safe range. www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm

[@ericjames7680]

@@DKCustomProducts Thank you for the help. Perhaps I will forget the FANGS for now. And as you had told us, I just got off the phone with Harley and they stated that 300 degrees is normal, then I told him yes but not at the recommended per manual temp just as you said! I would not be able to install the oil cooler you recommend because this would be a new bike purchase and void my warranty but I think the tank lift and wind deflector you offer would be OK. I would however have them install the Harley part fan/oil cooler that is standard on the Police bikes here in California.

[@ARCSSelfDefense]

I've looked at exhaust wraps, but I have heard stories of the wraps holding moisture and causing the pipes to rust out and disintegrate. Any thought or personal experience on this?

[@DKCustomProducts]

Yes, we address them in the video and comments linked here- kzbin.info/www/bejne/j5uagauQjayboZY

[@hootertexas9711]

But I love the fork fangs on a FLHR!! You guys ruined my day!

[@DKCustomProducts]

Sorry man. They are really good for reducing buffeting...but also really good at reducing the amount of air flowing over the engine.

[@1badsteed]

Great channel guys!

[@DKCustomProducts]

Thank you! 👍

[@Jockstrap716]

I have an 2006 softail Delux what can I do to make my bike run even cooler???

[@DKCustomProducts]

There is a list in this report- www.dkcustomproducts.com/why-how-to-cool-down-your-twin-cam-engine-part-ii-dk-cl-tc-dn-2.htm The items relevant to your 2006 are listed below A good tune #2, 4, 6, 7, 9, 10, 11, 12, & 14. Always feel free to email or call with any questions. [e-mail] 662-252-8828

[@jackx4767]

Also redirecting the oil exhaust lines away from the air cleaner and into a catch can instead. The oil being forced back into the engine through the air intake adds heat as it forces the engine to work more.

[@DKCustomProducts]

Thank you for watching, we appreciate your comment.

[@Jack-wi5qr]

Very informative. My 05 RK is going to go on a diet by loosing a lot shiny deflector parts. I’ve thought about trimming down the factory air box many times and using an external vent. Thanks for the information.

[@DKCustomProducts]

Glad you found it useful, and thank you for the comment. 👍

[@Jack-wi5qr]

@@DKCustomProducts I just drilled 2 2 1/8 holes into factory backing plate,already a different sound and better throttle response. Next is the external breathers tomorrow.

[@DKCustomProducts]

@@Jack-wi5qr Good deal, opening up that hot box and stopping that nasty air from going into your intake.

[@charlescastell4638]

Gents, do you folks by chance have a heat deflector [this video #1] that fits a 2018 M8 Softail? I've not had much luck finding any; any ideas? Thanks much.

[@DKCustomProducts]

We do not have any Cooling Wing Deflectors that fit the M8 Softail. We do have a written report and a video series on Why and How to Cool Down your M8. They can be seen at the links below. www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C Cooling down your engine will not only help it run stronger, but last longer AND radiate less heat.

[@charlescastell4638]

@@DKCustomProducts Thanks much. I am familiar with the mentioned videos and report, I've been thru it all. I was just hoping to find some sort of a heat deflector that I can use as a air scoop that will fir the 2018+ softail. I'll keep looking. Thanks for all of your good info!

[@mikebouchard527]

How about the harley cool fan takes the heat from the rear cylinder and blows it down

[@DKCustomProducts]

Yes, that is sorta what they do...they take the hot air from around the rear cylinder and blow it down. They are good for reducing the heat radiating to the passengers legs. HD specifically states, and our testing shows it to be true, that the fan does not reduce the temperature of the rear cylinder at all. But they do make passenger comfort a bit better if they passenger is feeling warm.

[@jaymurray7824]

Hi guys, does using external breathing bolts change my tune IE from when it was dyno tuned

[@DKCustomProducts]

You do not need to change your tune. They bike will run stronger because it has richer oxygen mix from not feeding that hot, oily, oxygen depleted air into the intake. But that change in oxygen is accounted for by the o2 Sensors in closed loop, and the LTFT in open loop. Here is a video you may find interesting/useful- kzbin.info/www/bejne/ZqfFhZ6Iq6uUbpI

[@freyatilly]

Guys. In UK it may be unlawful to remove the Cat converter. What can we do over here?

[@DKCustomProducts]

Leave it in. It will radiate heat on the right side, but it does not make the engine run hotter, or make a perceptible difference in power. If you were thinking of removing the cat to reduce felt heat, you may be interested in this video series, or the written report linked below. kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm

[@freyatilly]

@@DKCustomProducts Thanks guys

[@geraldgoodiii6993]

Oh man…. I love my fangs. I wondered if they had any affect on air hitting the jugs

[@DKCustomProducts]

Yeah, unfortunately they do. It is possible to keep them and keep the temps down, in some cases. Ideal operating temps, per Harley Corporate (not what folks say at dealerships) is 230* F. So if you can keep it there and run the fangs, you're good. Most can't.

[@Jeffmd2020]

Will your EBS backing plate work with my rc components air filter? I don’t wanna lose my filter cause it matches my front wheel

[@DKCustomProducts]

The Tranformer EBS will not work with your RC Components Intake. However, the all the EBS at the link below WILL work with your RC Components intake- www.dkcustomproducts.com/diy-external-breather-systems-528.htm

[@Jeffmd2020]

@@DKCustomProducts are those a drill and tap DIY system?

[@DKCustomProducts]

@@Jeffmd2020 Yes, the link shared is for a DIY Drill & Tap EBS.

[@randybard224]

Does adding a tank lift reduce your useable fuel in the tank

[@DKCustomProducts]

Usable fuel capacity is not affected noticeably when lifting the tank, it is the superficial low fuel, like the low fuel light coming on too soon due to the new angle of the tank. You can also add the Deluxe Option to the rear to help off set that low fuel light coming on. Here is a written report on the tank lifts that you may find useful/interesting. At the bottom of the report is where we talk about fuel capacity - www.dkcustomproducts.com/what-is-a-tank-lift-and-why-do-i-need-one.htm Here is a video on the subject that you may also find interesting - kzbin.info/www/bejne/goTLn6qieslqi9k Here is a link to the Tank Lifts if you would like to look at the product page or see some customer reviews- www.dkcustomproducts.com/gas-tank-lift-kits-c4.htm Please feel free to contact us with any questions you may have; [e-mail] 662-252-8828 Thanks for commenting! MB

[@garylam6233]

My biggest problem is I got rid of on electraglide because wife wouldn’t never ride with me and kept my Dyna Now when she does ride said she feels like she is on a birthing table on the Dyna Swears she will never ride again Do you have any suggestions for a more comfortable foot peg location as compared to the stock foot pegs Thanks

[@DKCustomProducts]

Something like the Triple trap, Bear Trap or Primo pegs might be a bit more comfortable than pegs. Then, if you add heel rests to either of those above, that will give even more foot positions. Then for a more refined look, but, still with almost as many different positions are these- www.dkcustomproducts.com/fatty-chrome-iso-footpegs-rubber-cushioned-w-heel-rest-dk-ky-iso-c-hr-f.htm She might also be more comfortable if the ride is not so rough, anywhere from the Bitubo's up to the NexGens. Please feel free to contact us with any questions; [e-mail] 662-252-8828 Thanks for commenting! KP

[@pmh1nic]

Thank you gentlemen.

[@DKCustomProducts]

Glad you are finding the videos useful/interesting. 👍

[@zacharydunn5847]

Nice info great explaining it as well the only thing I would suggest is maybe mics. The sound is echoing a bit and sounds like you are talking into a barrel

[@DKCustomProducts]

Thanks for the kind words. Glad you're digging the vids. Yeah, took us some time, and a whole bunch of different mics. We finally have some that are working really well. Check out some of our videos from the last couple of months.

[@six-pack1332]

I had a 2016 Fatbob that got HOT. Now I have a 2021 Sport Glide, far less heat.

[@DKCustomProducts]

Yeah, Harley did a better job of isolating the rider and passenger from the heat on the M8's...plus, with the larger oil cooler on the M8 Softails, they do run a bit cooler...but still too hot for their own good. Enjoy your ride! 👍

[@roycarlson6783]

As far as cat removal..check out American customs,awesome company and not very expensive exhaust alternative

[@DKCustomProducts]

Yes, we have quite a few Customers that get their set up and then put the TTI's in them. Turns into a nice exhaust. Here's a video from one of them- kzbin.info/www/bejne/h2GqfoKhp6iXgNE

[@roycarlson6783]

@@DKCustomProducts I was referring to head pipe cat,American customs guts out cat and replaces with a power chamber,almost like a 2 into 1 into 2...uses same heat Shields,bike looks stock,sounds great and cuts out heat. Alot cheaper than head pipe replacement

[@fabyanjim1]

How about an ultra cool aux oil cooler?

[@DKCustomProducts]

They definitely work. All our testing shows that the Jagg oil coolers are more effective, and they have a better warranty also. You can see them at this link- www.dkcustomproducts.com/oil-coolers-c134.htm That said, the ultra cool will perform better than the OEM. Depending on what bike you have, the UC may want you to cut your lower fairing for install. I would NOT do that.

[@CenobiteBeldar]

What about fan pulled oil coolers? They're like extensions to the ones already factory installed.

[@DKCustomProducts]

Depending on how you ride, most of the time it is better to cool the metal, so the oil never gets as hot, than to let the metal get hotter and then have to cool the oil after the effect.

[@Chilllybob]

If you decat stock header do you have to tune, has stock air filter, cobra neighbor hater slip ons

[@DKCustomProducts]

If this is the same 2022 SGS referred to in an earlier comment, No, no tune is needed. Here is a video on cats that you may find interesting/useful- kzbin.info/www/bejne/oaSWanqtl5iBmqs

[@jimmin9802]

I would like to pull the cats out of my 2020 softail standard and install the tti but really need to hear one upclose, not wanting too loud all the time. Thanks.

[@DKCustomProducts]

That's a good idea...it is not really a reversible procedure. Although, you can probably pick up stock slip-ons pretty cheap at some dealerships. Here's a vid you may find interesting (it agrees with what you said) - kzbin.info/www/bejne/fmebYpeiZ72SnJY

[@0000009ful]

I have a 2022 m8 road king. How can I see what Temps it is running at?

[@DKCustomProducts]

We always look at two temperatures: 1. Oil, which can be seen with a oil temp gauge dipstick. We've used HD branded ones. They are digital and are nice when they work, but do seem to have some reliability issues. We currently use the Jescustomaccents analog gauge dipsticks. 2. Cylinder Head Temp, this can be displayed on a Power Vision or a FP4, you can see both of those at this link- www.dkcustomproducts.com/efi-tuners-c74-262.htm Here is a video where we talk about what the optimum temps are for each (oil and head temps) - kzbin.info/www/bejne/qIiylYSFqampbKM

[@Ed.Johnson]

Your products and knowledge are first rate and appreciated. I have purchased you EBS (catch can), oil filter relocation kit, tank lift, decatted my exhaust by way of new header pipes, changed my intake and done a tune on my '19 Street Glide. Have you tested or an opinion on Harleys oil cooler fan and rear fan? I like the appearance of them over the other options, but is the cooling benefit worth the cost or us money best spent on alternatives?

[@DKCustomProducts]

Thank you for your kind words, and we appreciate your business. 👍 If your oil is going up over 230 F, the oil cooler fan will help cool the oil when at a stop, and up to 30 mph. Above 30 mph the oil cooler fan provides no cooling effect. The rear fan, aka CoolFlow Fan, is to reduce heat radiating out to the rider and passengers, it does not provide any actual cooling to the engine, but it is effective at reducing felt heat when at a stop or going slowly. You did not mention, but the Cooling Deflector Wings will reduce actual engine temp by around 10 F when moving. There is an entire list of things that can be done to reduce actual heat and felt heat at this link- www.dkcustomproducts.com/why-how-to-cool-down-the-twin-cam-engine-part-i-dk-cl-tc-dn-1.htm There is a video series on the subject at this link- kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C Feel free to email or call with any questions: [e-mail] 662-252-8828

[@journeywiththerocks]

Great video. Have a good one

[@DKCustomProducts]

Thank you for the comment. Glad you enjoyed and hope your weekend is great!

[@c.b.jr.1539]

Dude! I didn't know Tommy Chong was a H-D mechanic. Awesome!

[@DKCustomProducts]

Me neither.

[@damianoriccardi1268]

Buongiorno avrei 1 domanda..sarebbe possibile ricollocare il radiatore dell' olio piu' in alto sempre davanti al telaio sulla road king modificando solo le tubazioni nel m8 107? Grazie per 1 risposta..

[@DKCustomProducts]

You could do that, but seems like less work to mount the auxiliary oil cooler on the left side downtube, then no modification of the exhaust is needed. Here is a photo. www.dkcustomproducts.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/a/u/auxiliary_oil_cooler_sg.jpg As you can see, it can be slid quite a ways up on the downtube.

[@bradlozano2571]

How about adding aftermarket Oil Coolers?

[@DKCustomProducts]

Yes, that is a very good option, one that I have done on all my Harley's. It is not a low or no cost mod, which is why we did not put it in this video. You may like this video series- kzbin.info/aero/PLb3bvZgbH92_3s-2vv63QggFJ3nteFd_C This video shows how much a good oil cooler can cool down the oil- kzbin.info/www/bejne/bHLLgaSModt4Y9k

[@bradlozano2571]

@@DKCustomProducts Thank you👍

[@calimilk1113]

Where can i find the breather kits for iron harley, amazon says out of stock???

[@DKCustomProducts]

Take a look at the link below, these are all for Sportsters, depending on which air cleaner you have. If you are unsure which one will fit your particular set up, feel free to email or call. [e-mail] or 662-252-8828 www.dkcustomproducts.com/91-up-sportster-big-twin-evo-c75-86.htm

[@calimilk1113]

Thanks!!!!

[@tonyl8314]

Does removing the cat help cool down the engine or the exhaust?

[@DKCustomProducts]

Removing the cat will reduce felt heat. It does not reduce actual engine heat. You may find this video on the 2 kinds of heat useful/interesting- kzbin.info/www/bejne/hGHOfZSMhs2VjZY

[@rodneyhirsch2340]

Stuck in California, for now. Not paying California 100000 for a fine. But as soon as I get back to Idaho I’ll be using your products again. My experience is your right, everyone else is wrong. Electra glide 53 mpg at 80 in Idaho with your products. No tune ran better than stock. I get called a liar as well so don’t worry about it.

[@DKCustomProducts]

Thank you for the comment and kind words. Quite a few of the mods listed in this video are not in violation of any Cali laws. Tank Lift CDW Exhaust wrap Floorboard extensions Coil relocation Just off the top of my head. btw, never heard of a private individual getting a fine for making their bike how they want to in Cali...unless they were obnoxious with their exhaust. Good to hear you've enjoyed our parts in the past, and plan to again.

[@biondanishgenomeinstitute8193]

Adding RVS to the oil should also help, as less heat would then be produced.

[@DKCustomProducts]

Yes, that make sense...but how much of a reduction. Regardless, it seems like it would be useful just for better lubrication. 👍

[@biondanishgenomeinstitute8193]

@@DKCustomProducts When I added RVS to my 1982 BMW R100 engine (in good condition) I didn't feel more power, but temperature came down about 10C on the guage dipstick after 1000 km. But its difficult to notice because it happens so slowly. It did turn the oil black almost right away as it loosens all the dirt before oil change and adding the other half. I know its excellent for restoring compression on worn engines. The Finnish producer says people usually first notice less heat and smoother running. Maybe the best source of info are the TUV and Fraunhofer reports on the Finnish site.

[@DKCustomProducts]

Thank you for the info! Going to look into it. 👍

[@ridered7394]

Removing the cat on my 100% stock 22 road glide, wouldn’t that require tuning?

[@DKCustomProducts]

I don't believe so, but we have not had a '22 on the dyno yet to see how the AFR's look. On the 2017-2021 models it is not necessary. kzbin.info/www/bejne/gpPCZmqQlK6jo9U

[@martinwall7297]

aluminum-bodied reusable oil filter, less oil restriction, faster oil flow, while cooling oil. my oil pressure comes up quicker when starting the bike up. hot or cold.

[@DKCustomProducts]

Yes, definitely a great mod. It is something we do to all our rides. Here's a video on them- kzbin.info/www/bejne/lZC6k6iOZq6HZ8U

[@tmar0075]

If u do an exhaust wrap..can u reinstall the heat shield over it to keep the original look or is it better to go with true duels instead?...Ride Safe

[@DKCustomProducts]

You can absolutely install the heat shields over the wrap. Many do just that. There are photos in this link of that- www.dkcustomproducts.com/titanium-exhaust-wrap-dei-reduced-heat-improved-performance-dk-dei-t35.htm Also, you may like this video which goes into some detail and has photos also- kzbin.info/www/bejne/j5uagauQjayboZY

[@tmar0075]

@@DKCustomProducts Thanks appreciate the feedback😊

[@DKCustomProducts]

@@tmar0075 You're welcome! Ride safe!

[@tracymccann2483]

Do I need a fan for my bike it's a 2021 harley sport glide 107

[@DKCustomProducts]

Every bike is different. Where and how each bike is ridden is different. And there are a variety of ways to make sure the engine is running in the optimum temp range. The first thing is to know what temp you are running, and if it needs to be lowered at all, and if so how much. Most do need some help cooling down. Our suggestion is to start with smaller, less expensive things...one at a time, and only add cooling mods that are needed to get your temp down. Link to what the optimum temps are for your M8 kzbin.info/www/bejne/qIiylYSFqampbKM Link to a Report that has a list of cooling mods- www.dkcustomproducts.com/why-how-to-cool-down-your-twin-cam-engine-part-ii-dk-cl-tc-dn-2.htm Always feel free to call or email us with any questions. We are glad to help. [e-mail] or 662-252-8828

[@paulrevere4326]

I have an 2018 street glide. If I remove the cat, I will loose back pressure. At that point I can put some TT’s in the slip ons to help replenish back pressure. Do I take the baffles out or not?

[@DKCustomProducts]

Good question. Even if you remove the cat, the baffles in your OEM slip ons will provide plenty of protection against reversion. You do not need to do anything to add back pressure. You will not lose any low or mid range torque. However, if you want to remove the baffles from your slip-ons and put in Thunder Torque Inserts™ you will gain a significant amount of power. (that is whether you leave the cat in or remove it). Here are a couple of videos that you may find interesting- kzbin.info/www/bejne/pqOZq2NmnLFoj8k kzbin.info/www/bejne/qKXHgp9-iKp-qNE

[@paulrevere4326]

So remove the cat and the baffles (Cobra slip ons) and add the TT to the slip on, correct?

[@DKCustomProducts]

@@paulrevere4326 That is what I would do, and that will give you the best power increase.

[@francismarion1351]

Question.. so I have a 2019 Electra Glide Standard. It came pretty stripped down and I have been making g it my own. That said it does have any side deflectors at all. Should I leave it this way or just look for the one on the right side to promote directional airflow? It seems like it can go either way.. Also baffles. Are they strictly for stock exhaust? I have after market headers and CFR slip on. It seems I should have stage 1 and exhaust covered . But open to improvements

[@DKCustomProducts]

Great questions. Removing the left side will create more flow than removing the right side. Less obstructions on the left. It will also feel a bit cooler if you leave the right on and remove the left. Yeah, the CFR baffles are NOT overly restrictive...it is mostly the stock mufflers that are overly restrictive. That said, not all State I's are created equal...there are Large variances. You may find this video helpful/interesting- kzbin.info/www/bejne/fXyYqWaimLapgLc

[@donaldkvarta8723]

Thank you guys for another excellent video. Please keep them coming because these videos or a wealth of information. It's nice to have mechanics like you that can talk about the V-Twin air-cooled motor and get the most performance out of something that supposedlyyyyyyy, old technology. If you take care of it gets your ass home don't it.

[@DKCustomProducts]

Thank you for the kind words, appreciate your comment, and agree with you on motorcycle boots not being made for walking. lol

[@tbo9421]

God, dear God, plz get rid of these stupid temu ads. You'd think KZbin and China were sleeping together with the amount of ads we have to endure. Now on topic great video.

[@DKCustomProducts]

Glad you found the video useful/interesting. 👍

[@Hughes1174]

I’m finding different answers to my question. I have stock 2021 Ultra limited with plans on upgrading air cleaner and adding slip ons. I want to remove the cat Can I do it without retuning (keeping stock air cleaner and muffler). Saw your video where upgrading air cleaner did not need tune. I realize I will need to tune the more I upgrade, but at what upgrade step is it necessary?

[@DKCustomProducts]

Our video is about 2017-2020 M8's, not 2021's. We do not yet know about the 2021's. HD changed the ECM and we have not had the time to get one on a dyno to see if the new ECM will adjust. The 2017-2020's will adjust to removing the cat. I suspect the 2021's will also, but can not say for sure until later this year when we do our testing.

[@Hughes1174]

@@DKCustomProducts thank you for the reply and I’ll be looking out for your 2021 testing info.

[@DKCustomProducts]

@@Hughes1174 Cool

[@garyboman5018]

I just watched a video where a guy removed the right side muffler and drilled out the cat with a large bit, then cleaned up the inside with a cylinder hone and shop vac. Very clever. I'll be doing this when the warranty runs out. Nice thing is no pipe removal necessary!

[@hoopscorner6458]

Simple, water cooled!

[@DKCustomProducts]

There are no truly water cooled Harley's (except for the Pan America and the new Sportsters, which are not really selling). Here is a video you may find interesting- kzbin.info/www/bejne/rYO1pYWPjNJoqNk Thanks for commenting! MB

[@ut1004bp]

Ok, I thinking about adding one Mid frame shield/scoop , but for the mid-frame shields, looking it over, I'm going to have to ask as a matter of engine cooling only (not rider comfort issue considered): Don't you think removing only the right side (rather than the left) would better serve? The left side shield is farther from the cylinder head and partly due to being out from the cylinder and not having a large airfilter box in front of it, its likely can scoop more air due to this, and by removing the Much-closer to the cylinder, right side shield.. I wondering,, wouldn't esp at no or slow movement traffic, that the heat could escape easier as opposed to the left side (since the cylinder is tucked farther under the tank)?

[@DKCustomProducts]

We recommend having the right side deflector in place and no deflector on the left for the following reasons. 1. There is more heat on the right, so having the scoop there also shields the rider and passenger from some of that heat. 2. The air flows much smoother from right to left, than left to right. So by leaving it on the right, it will result in more and faster flow of air past the rear cylinder. 3. If at any point you decide to add cooling fans, then #2 above is even more significant This has been our experience, both in real life testing and with a fan and smoke pen. We did not video that, so we may do that experiment again with the smoke pen & video it this time.

[@paulmcneil5529]

Adding an oil cooler or lower the oil temp 20ﾟ.

[@DKCustomProducts]

???

[@quickshoe6]

Thank you for sharing.

[@DKCustomProducts]

Thank you for your comment! 👍

[@ee5172]

great ideas guys, thanks!

[@DKCustomProducts]

Thanks for watching! Glad you're enjoying.

[@kevinpummel1597]

Don’t forget the air deflectors on the bat wing

[@DKCustomProducts]

Great point that we missed. Thank you!!! 👍

[@larryp4055]

What are fork faings ?

[@DKCustomProducts]

They are wind deflectors that mount on the forks. Here is a link to a photo of some- www.harley-davidson.com/content/dam/h-d/images/product-images/parts/batch-3/57400143/57400143_OB.tif You can see how they block a significant amount of air from flowing over the engine.

[@dannyburgess2781]

What. Tank. Risen. Are they. Kit. Rise. It.

[@jamesmccanne331]

Can triple tree rake be put on a 2019 HD trike?

[@DKCustomProducts]

Yes, there are several companies that make rake kits for the HD Trikes. One place you can contact that sells them, and can install them if you want, is Cut-n-Shoot Customs in Texas.

[@jamesmccanne331]

@@DKCustomProducts do they have to cut the frame to install the triple tree?

[@DKCustomProducts]

@@jamesmccanne331 NO...not on any of the ones I've seen, or would consider using.

[@jamesmccanne331]

@@DKCustomProductsdo you have a triple tree rake on your trike? And if you do, how do you like it, does it steer easier?

[@jamesmccanne331]

@@DKCustomProducts Do you have a after market triple tree rake on your trike?