Doctor Corally - Varioprop S2R - Full Video Manual

How to bind, use and set-up Varioprop S2R radio in Team Corally Cars (Python, Kronos, Dementor, Shogun, Triton, Mammoth, Mooxo)
VARIOPROP UNO S2R LINKING/BINDING PROCEDURE:
1. Switch On the Transmitter with pressing on the Transmitter button for 2 seconds
2. The red LED is flashing slow
3. Power On the receiver
4. The red receiver LED is flashing slow
5. Press and hold the receiver button until the LED stops flashing
6. The linking is finished once the receiver LED stop flashing
Please note! The transmitter stops the linking procedure after the third double beep signal.
►Enter the exciting world of Corally:
world.corally.com/
►For assistance, visit:
support.corally.com/
►Find for You local dealer:
dealers.corally.com/

[@Jonathan-bk7gs]

Thanks for showing me how to use my Arrma Typhon!!!

[@nicolaswosny6914]

I love team corally !

[@franckroyer7515]

Bonjour et merci pour les sous-titres en français

[@mr.miami.3053]

I wonder how many exact of these were produced

[@markusgerhold8116]

Sehr Hilfreich... Gibt es ein Video um den Regler einzustellen? Zum Beispiel die 3 Temperatur Stufen. Möchte gerne auf die mittlere einstellen. Danke und Grüße

[@kamchan7606]

Hi there, I just purchased one of this. And I find that the demonstration you had on here was quite different to the one in your manual. Like I didn't even have to open the receiver box but the binding still got done. Is failsafe already a standard feature for this model? Or you'll need to activate it yourself? Also, I am using a 22.2V 6s Lipo battery, but somehow its size just doesn't fit into the battery compartment. So, can I still use it by not placing the battery fully within the compartment as long as the strips are tighten? Thank you!!

[@TeamCorally]

Binding is done out of the box. Same with Fail Safe. At this videomanual we show all features of the radio, when You lost the connection and binding is necessary or want to change Fail Safe settings. Battery needs to sit tight. Do You have newest 2021 line car? We make the battery compartment bigger.

[@kamchan7606]

@@TeamCorallyI had the 2021 model. And the problem I have now is the car can go forward and Brake but no reverse. Anything I can do to fix it? Thanks

[@TeamCorally]

That's the ESC setup, check the manual attached.

[@LiquidXiron]

I have issue with my Punisher, I’ll check the esc maual again.

[@Kyle_v2]

This is accually a pretty sweet car my dad has one and lets me use it.

[@TeamCorally]

That is how we like it .... father and son together :)

[@franciscocordon6285]

I have a quick question. I have the kronos truggy. It shuts off randomly when running it a bit hard. It is all stock. Only aftermarket is a fan on the motor. Have any advises or solutions?

[@TeamCorally]

maybe the overheat protection turns on? If You bash hard, change pinion gear for smaller (1-2 tooth less). If You still will have this issue, please write at [e-mail], proper person will help You.

[@stellageldenhuys6295]

Help needed!!! My daughters Muraco keeps on running the lipos below 3.0 volts. How do I check or reset the Voltage cut failsafe thing? I want it to cut out at 3.7 volts. Help!!! Also, I want it's punch setting lower on 6s.... the Team corally user manual is extremely confusing.

[@TeamCorally]

Hey. It's a radio manual. Of you have any questions please write us at support.corally.com

[@1979lepeltje]

Nice video! Can you tell me if it is possible to connect Led lights on the receiver for driving in the dark?

[@TeamCorally]

There's one slot on the receiver to plug in LED.

[@1979lepeltje]

@@TeamCorally Thanks for your answer! I have watched the video and thought i saw a empty slot, so this can indeed be used for Led lights. Many thanks for the quick reply.

[@scottbeard7041]

Great video solved my issues thanks

[@diamandt5598]

@Team Corally I have a Corally Kronos V1 and Service Pack 2 is on it´s way, so the car should be fine, but setting the EPA just won‘t work. I put the throttle trigger in full brake position and turn the radio on. No blinking or beeping from the radio. I tried everything to make it work several times but nothing works. I don‘t want to kill the servo so what else can I try to make it work?

[@TeamCorally]

Dear Pierre, Please have a look on page 5 in the radio manual. You can easily set the dual rate www.dropbox.com/sh/5gy5477jfowj4at/AAC3fb7wvHiHDEuOCJopJQc9a?dl=0&preview=Varioprop+S2R+TX_manual_EN.pdf

[@diamandt5598]

@@TeamCorally So the dual rate does the same as the EPA? If so, I already did that.

[@Wooskii1]

I just got a new Kronos V2 and the ESC power button doesn't seem to work, it starts the fan as soon as the battery is plugged in, and all controls are working, but when I push the power button the car and fan stay on and bound while the red light goes off. Any advice would be greatly appreciated! I can turn the light on/off all I want but the car stays on and bound. I can't find anything in the manual or online about the problem. Please help...

[@TeamCorally]

Hey please contact us via e-mail - [e-mail]

[@charlesmcguire9711]

What radio protocol does this use? Thanks.

[@jonpg28]

I replaced my torox 185 on punisher its moves left to right only but I can't get it to do anything else

[@TeamCorally]

Hey. If you have any issues please write us at support.corally.com. You probably need to adjust the end points.

[@harryflow3270]

Hi there I have a murraco my rc is pulling to the left when I press the throttle please could you tell me how to resolve this? Thanks

[@TeamCorally]

Hey. Please write to us at support.corally.com

[@LiquidXiron]

I have an issue with my punisher, car at idle when I hit reverse I can see the ESC receiving signal but it does not moves unless I press the throttle harder. Is that standard operation?

[@TeamCorally]

You have 3 different option on the ESC work. Forward only, forward/brake/reverse and forward/reverse - check the ESC manual to change that if You want. forward/brake/reverse works just as You say. For instant reverse, You need to change the setup

[@LiquidXiron]

@@TeamCorally Thanks for the reply, if that's how it works I'll just leave it as it is.

[@TeamCorally]

It's Your call, but in Our opinion is the best option, that's why it came this way out of the box.

[@mattstork2203]

Is the Batt port on the reciever for adding a fan?

[@TeamCorally]

yes there is!

[@rkonitz]

I would like to know if it's posdible to run the receiver on 7,2V without frying it?

[@Wooskii1]

I think it's in the manual

Manual says up to 6v, but that is with the gas vehicles, where you plug the battery directly to the reciever. With the eletronics ones, the voltage goes from the ESC..a dont know if that makes any difference, but i hope so. I hope you can run it on 3s lipo

[@SentinelGames]

I just purchased a Python V2 and with the throttle limiter switch at 50% it runs fine. However when I switch it to 75% the car moves in reverse all by itself with no transmitter input from me. What do I need to do here?

[@SentinelGames]

Ahh. I didn't understand how the 7:3 / 5:5 switch works. I thought it was something you could adjust on the fly however I now understand it controls the ratio of throttle to break and each time you alter this switch setting you need to recalibrate the ESC. It's not something you switch on the fly.

[@TeamCorally]

Yes indeed:)

[@SentinelGames]

Incidentally, the car (Python) is absolutely fantastic! Built perfectly out of the box, such high quality components and craftsmanship. I didn't even need to adjust the steering trim, it tracked straight out of the box. Handles like a dream too. Amazing. Brilliant job Team Corally - will be buying many more of your cars in the future. 👍

[@scottbeard7041]

I have same problem but mine goes in reverse every time I turn it on!

[@Bluecray]

Mine on 50/50 is good and I've checked throttle is in neutral (the trim) but if I put the switch 70/30 it takes off why? I was told 70/30 is the best setting

[@leegorman3329]

my radix won’t respond to the controller, it recognises the battery cell but will not respond no matter what, it just flashes red,

[@TeamCorally]

please contact us via support.corally.com

[@michaelgarland579]

How do you get ESC thermal protection off on the skeeter

[@TeamCorally]

Hey, it's fairly simple, take a look on the manual, You just need to reprogram the ESC. You can do it with the button, no other things required. Check for the manuals at world.corally.com or contact us via support.corally.com if You have any troubles.

[@michaelgarland579]

@@TeamCorally already did that I reprogrammed it and it's still not working is there a video on how to reprogram it to make sure I'm doing it right can we talk on the phone

[@michaelgarland579]

@@TeamCorally can you please send me a video on how to recalibrate your ECM on the skeeter I looked in the book I kind of did it but I'm not sure if I did it right

[@michaelgarland579]

@@TeamCorally there is definitely something wrong with it the last time I was running it it got hot and I didn't let the truck cool down I just turned it off the immediately and the next day it's stuck on thermal mode

[@TeamCorally]

Please write us at support.corally.com we will be able to help you there

[@diariomotero491]

por favor subtítulos en español, gracias.

[@bigbullman9320]

can you talk please thanks cant understand this at all

[@rc_racing_uk]

would of been nice if he spoke to say what he was doing

[@kinggage]

Turn on captions

[@giusepperuggeri7823]

Mi fi spiace con me hai cjiu so praempte

[@walterlaber7788]

Reden Is schon schwer!

[@giusepperuggeri7823]

No vogio scrivere