Dodge Avenger - Battery Replacement

In a previous video we had a look at a Dodge Avenger that had a problem with the AIR Check Valve and also was in need of a battery. In this video I show you the process of swapping out the battery. In case you missed it: • Dodge Avenger: P2441 A... -Enjoy!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/...
The South Main Auto Amazon Store:
www.amazon.com...
AES Wave Automotive Diagnostic Tools: www.aeswave.co...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.

[@-BuddyGuy]

If you're thinking about calling Eric and leaving a message, don't bother him, bother me. I will give you the auto advice you deserve. For example, here he sprays the terminal nuts to loosen them up a little. That is a waste of penetrant and could damage your lungs. To safely get some purchase, lever your wrench against the other terminal. Battery terminals are located specifically for you to do this. If you get sparks it means you're not holding the wrench tight enough against the terminals.

[@SouthMainAuto]

At what point do you let go? After the heat has loosened the bolt I assume? GREAT TIP!!

[@miguelare3]

Lmao 😂😂😂 what is your hotline number?

[@lesbender236]

@@SouthMainAuto If it gets hot,that means the battery if fine,put it back in and charge them anyway!!

[@greatnortherntroll6841]

I can just see some dumbsh** actually attempting this! =8'O

[@throttlebottle5906]

bah the battery is weak anyway, it would likely just make a nice short term hand warmer :))

[@ericstoneberger4504]

not sure if you'll read this, but I just wanted to personally thank you for uploading content. Currently in college learning the key systems in cars, but what you teach me is far more valueable in alot of ways. Keep doing what you do man!

[@SmittySmithsonite]

He reads 'em all - even my 7 paragraph novels! 😁

[@roadkill5333]

Eric Stoneberger I think he reads most of the comments. This is where I try out some of my new comedy routines. It's a captive audience, and can't throw rotten fruit, if it's bad comedy! At least he hadn't banned me yet, so it's a least a little funny!

[@roadkill5333]

Smitty Smithsonite I've even read some of your 7 paragraph novels!! I'm not into the paperback version, tho!! You need to do them in hard cover editions!! For us hard core comment readers!!

[@Blazer02LS]

Eric shows it like it really is, not how the schools teach it.

[@CvonEssen]

Hilarious!! That's fine entertainment there....

[@chrisgorgas1929]

When I saw the title of this video, I thought, what's so hard about that. Well, you learn something new everyday. Thanks Eric O.

[@tom488]

Eric - change your answering machine message to state that anyone leaving a msg. for car advice WILL have their msg. published on KZbin. Then, once a week or so, just post a video of the messages you get... we'll take it from there :)

[@SouthMainAuto]

Don't temp me....

[@dave_n8pu]

@@SouthMainAuto Sounds like a good idea to me. :)

[@markegan5330]

+1 for this. Great idea

[@CubasAutomotive]

Never know ppl. If some are already ignorant to begin with leaving messages, I'm sure others would leave them just to hear themselves on a video, knowing it could possibly be aired. Ugh ppl.

[@k0rndog93]

The weekly videos would be longer than a feature length movie!!

[@AstroTools]

"Battery removal procedure: Step 1: Remove driver's side front wheel" *Sells car*

[@SouthMainAuto]

Did this on a new Traverse the other day... Step one remove floor mat, move seat rearward, remove plastic trim ( at zero degrees mind you) remove floor cover, disconnect battery current sensor, 3 other random wires and terminals with wires just long enough to reach the posts and then try to lift out 80- lb battery that you can just get the tips of your fingers on, swear, throw a few tools, install new battery and the then go tell customer car is done and it was a piece of cake :)

[@AlvinLuckenbach619]

Saturn Outlook, GMC Acadia is also under back seat and requires special direct vented battery with vent hoses attached. At least the kids never spilled a squisheee on top of the battery hole.

[@ivanblack3234]

@@SouthMainAuto do you charge for new knuckles an fingernails? Lol

[@vipor96]

My Jeep battery is the same under the passenger seat. Had to darn near remove it to swap batteries.

[@throttlebottle5906]

that admits failure, because you bought it to start with lol~!

[@Jay-xb6nc]

Eric, congrats on winning the Cardone challenge! It's so cool what you are doing with the money. We need more people like you.

[@dmayse1000]

??

[@nabob14]

Awesome! This is my favourite vehicle to change a battery on! You have no idea how much my elbow has thanked me for hitting it against the wheel studs or brake caliper... or how much my neck loved having cold salty slushy water dripping on it in below freezing temps while replacing/repairing something down in there... my favorite! Honest! I'm lying.

[@1607rosie]

Eric you didn't get the plastic inner fender tucked behind the fender, doubt it'll really matter. Your still my idol. Your the king of rust and shorts . Keep up,the good work.

[@CTSCAPER]

If someone told me you'd have to go through that mess to change a battery I wouldn't have believed them...until I saw it. That's a silly design and I wouldn't buy a car for that very reason. If that's how they installed the battery what other silliness is in there.

[@70kid8]

My wife has a Dodge with the battery in the same location. 30 minutes every 5 years to change the battery isn't really a big deal.

[@davestout8471]

It's a Chrysler, there's tons of silliness going on.

[@excelerater]

It would have been better on the pass side . Weight distribution

[@roadkill5333]

Chevy makes a Corvette, with the PCM in the same location!! Can you say "ITS WHERE COMPUTERS GO TO DIE"? Ivan at Pine Hollow Auto Diagnostics just did a video on one! It was a horror show!!

[@PandaMan02]

@@70kid8 good luck if you need to jump it

[@AaronBelknap]

What a design snafu! I bet they engineered everything then thought "oh crap, we forgot the battery!" Then they installed there..... Great video. I'm glad you don't return calls. It's nice enough that you film your work for the rest of us to see and work on our cars if we have the right diagnosing tools. I thank you for your work and sharing your knowledge with the rest of us. I wish I knew what you forgot! Keep em coming!

[@greatamericansystems7325]

Spinning that brush on the positive terminal made me realize something I have not seen in your videos. Eye protection. Please. We love you.

[@bill3641]

Eric, I'm not happy , your expanding our awareness of the ridiculous designs of newer cars and trucks is running up the value of cars that are 15 years old. Thanks for what you do.

[@kevinburks110]

I've watched your Jeep hat deteriorate substantially over the past few hours. Its like a time lapse. A few videos ago it was nice and new looking and in this video it's just now broke in!

[@mr.nobody4900]

A true professional ..Is always a pleasure watching work. Mr. Eric O. Two Thumbs Up

[@zigner]

Love the "novel" being left on the answering machine! The logic from these kind of people is, "the request for no calls or messages from youtube users applies to everyone else, but my problem is special, so I can leave one!"

[@realvw]

I been watching your videos for quite a while now. This is the first time I have commented. You sir are the bomb, you should be an instructor. Thanks for all the teaching you do here on KZbin. Bless you and your family.

[@TheTheomax]

Battery's Ball joints and Brakes the big 3 what's not to like about these kind of video's . Then you got electrical issues and whatever else comes through his shop doors. Sensor this and sensor that we got it all in one spot @ SMA LLC. Eric is the man when it comes to keeping all of us entertained.

[@nhra7110]

thanks for the Tiger Tool pliers tip...exactly what I have been looking for, for those 2-piece Chrysler trim clips!

[@arthurfricchione8119]

Who would ever think of looking for a battery in the fender well. Trunk maybe fender well not so much .Thanks for the video Eric, hope your feeling better. 👍.

[@flyboy2610]

Thanks for posting this, Eric! My son's girlfriend needs a new battery in her '08 Avenger. They're coming over for our family Christmas tomorrow. He's going to buy a new battery on the way over, and we'll install it after lunch. Shouldn't be too bad weatherwise. It's supposed to be in the middle teens (f). Looked for info on how to do it, and your video came up!

[@elcheapo5302]

I really needed some SMA today. I feel better already! Thanks, Eric. Looking forward to part 2!

[@siduramaxde]

Thumbs up just for hanging up on the jack wagon youtuber!

[@rhkips]

Wrench + Battery = Intro to Welding. ;D

[@SouthMainAuto]

I literally lol'ed at this one, classic!

[@jdtractorman7445]

Or the fourth of July will come earlier than expected with a marvelous firework display.

[@for2utube]

That, plus burned flesh.

[@alanmatthews5949]

Scottie uses this to reset the MIL light!

[@jamesu]

Good Morning Eric. Hope you are feeling better now. Have a great day sir!

[@InsideOfMyOwnMind]

I just watched an entire video from end to end on how to change a battery in a vehicle that you couldn't pay me enough to own and I'm still happy about it. I'm losing my mind.

[@BLACKSSG85]

Eric next time you get one of them you can unbolt the remote negative terminal up on the strut tower first. That is the same as disconnecting the battery and you can remove the negagive cable end off the battery outside the car. Makes life a little easier. -Justin Sliwka

[@donnierobertson3088]

Nice job again like always

[@Paul1958R]

Etic, Thank you for another great video and glad you are feeling better!! That is an interesting location for a battery. It didnt seem to bad to get to other than removing the fender shield. Ptetty straight forward. SMA#1 God bless Paul

[@baxrok2.]

I like the way that you took that tire off. Comes with a lot of practice. Thanks Dr. O!

[@SouthMainAuto]

and focus....

[@baxrok2.]

​Yeah, don't want to loose a tooth or get yer nose busted up!

[@BigDaddy_MRI]

I was gonna call you. But heard your answering machine. You said you wouldn’t call back. And I cried. But it’s ok. I understand. [sniff]. 😂😂😂😂 Great video. Thanks Mr. O. Love the SMA vids. Keep them coming.

[@davjociestanski5743]

Eric. Thank you for you time to even give a short one on battery change which will help some body do a battery change

[@robertrobinson8242]

What a dumb place for a battery... great videos Mr.O and Thank you for your help

[@vee985]

I didn't see that one coming. Awesome engineering.

[@TylersNeighborhoodGarage]

The original step 1 should have been driving on past the Chrysler dealership. That's ingenious, using the battery as an impact-absorbing feature in the event of a left-front collision. Altima, Accord and Camry battery location? Right under the hood. It CAN be done as long as you aren't having to adapt another make's platform because you don't have the money to develop your own.

[@Jake-ul5nl]

i used to work at walmart TLE my manager said we are to install these at no charge with purchase of new battery. still got to buy the battery but 15 - 20 minutes to install a battery is stupid. normally only takes me 3-5 minutes on a car like the hyundai sonata. great video eric.

[@bobmoy3406]

I was thinking a video to change a battery, Mr O is getting desperate for videos, but after watching it I'm glad he made it. Great job Mr. O. At least the Euro trash locate their batteries behind the rear seat. Also why didn't the Engineers reverse the the post location where the negative is remove first. Lucky for me after donating my Taurus, I now owns only Honda, Lexus, Toyota, and my Euro trash BMW.

[@HarryManI3ack]

Not to be "that guy", but (there is always a but after saying that) that inner fender didn't get tucked back in all the way. Love the vids. Thank you!

[@pdseifert3]

Awesome video as always! I always appreciate your time and effort in making these videos.

[@chrisb3017]

Dodge Durango battery under front passenger power operated seat. Great video

[@0509kj]

10 years on a battery holy @#$& Batman! That's a dream here in Phoenix. We get 1-3 years on average in my experience depending on the vehicle. The heat dramatically shortens their life. Having to do this that often would just make me even madder lol. Guess it's a trade-off to not have the salt/rust. Whoever thought up that location for a battery was clearly not thinking about serviceability, or the little safety item you touched on there. Thanks for the videos!

[@kalanikaau1]

Many years ago, while in a junior college auto mechanic program, we were taught to always disconnect the battery negative cable first ( provided the vehicle was negative ground.) Through the years as a mechanic you did run into situations where it was more convenient to disconnect the positive cable first. Once you've done "arc welding" by somehow grounding the wrench while doing so, you learn to be very careful. The practice is not taboo, you just need to know the consequences, generating sparks near a battery can lead to "kaboom" !

[@GarthGoldberg]

I always keep my 10mm wrapped in electrical tape. And I'm wearing an adult diaper, also for safety.

[@for2utube]

An old mechanics glove, with the tip of the middle finger cut open, works also.

[@mboelts]

"Step one, is removing the left front tire"...HAHAHAHAHA. I'm crying I'm laughing so hard at that.

[@aleblanc3547]

It was a long time ago, but I remember a story about how a bumper had to be removed in order to change the license plate light bulb. I don't know whether or not it was made up, but even 50+ years ago they were complaining about the lunacy the bean counters and engineers made for car owners and mechanics. I guess we can lay a little blame on the government's rules for crash safety while we're at it. Thanks Eric!

[@jimmydeen58]

Great Video.. "So much for the old way of just popping the hood and swiping out the battery LoL"..

[@GarthGoldberg]

So, if you just want to check or clean your battery terminal connections, you have to lift the car, remove the wheel, the inner fender liner, the support brace and the battery hold-down? And then reverse all of that?

[@bill3641]

Heaven forbid , that you need a jump start. You call AAA and they just laff.

[@Blazer02LS]

Jump terminals are under the hood.

[@chrisstoddard1144]

Did you notice that the battery lasted ten years without attention? Much ado about nothing.

[@dmayse1000]

just changed the factory battery out in my wifes 07 sebring damn thing lasted 11 years and very minimal corrosion on the terminals... 30min battery replacement every 11 years i can handle oh and there are jumper terminals on the driver side shock tower under the hood for a jump just in case

[@bigb7157]

Also batteries in the trunk seem to last longer as well. Less direct heat being away from the engine, I’m guessing.

[@lexmaximaguy8788]

Most chryslers..step 1 pour gasoline step 2 light on fire....fixed.

[@roadkill5333]

LEX Maximaguy87 NOT!! Step 1) POUR GASOLINE! Step 2) DISCONNECT THE BATTERY, POSITIVE FIRST, LET THE WRENCH GROUND OUT ON THE BODY, CAUSE A SPARK, WELD ITSELF TO THE BODY, CAUSE A MASSIVE DISCHARGE, OVERHEATING, AND EXPLOSION, RUN AROUND SCREAMING WHILE TRYING TO RUB THE BATTERY ACID OUT OF YOUR EYES, AND LET THE FIRE CATCH THE GASOLINE ON FIRE, WHILE THE AMBULANCE TRANSPORTS YOU TO THE HOSPITAL, FOR DESIGNER EYE PATCHES WHERE YOUR WORKING EYES USED TO BE!

[@throttlebottle5906]

why waste the gas, the often burn by themselves :))

[@lexmaximaguy8788]

@@roadkill5333 LOL

[@lexmaximaguy8788]

@@throttlebottle5906 haha true.

[@alanmatthews5949]

Step 1A. Shake well before step 2.

[@AntonioClaudioMichael]

Great Update Eric O

[@FABAutomotiveDetailing]

Well it’s almost winter are going to start the “what’s up Wednesday’s” again?

[@ethelryan257]

What an interesting place to put a frequently changed out piece of equipment.

[@likearockcm]

Stared sitting down for some repairs (or I never noticed) good idea to save your back👍 There is few injuries as chronic and painfully debilitating as back injury.

[@mph5896]

I can't figure out my car. Hey maybe I'll call Eric O up while he is at work trying to fix a dozen cars per day and ask him. Wait, his message said to beat it. That truly can't apply to me. I'll leave a very detailed message so he will know this is important. Guess I should leave my location as well so he'll know its a long distance call. A week later, I hate Eric O. He never returned my call. DISLIKE!

[@Deviant365]

Perhaps Eric could set up a forum so people can go there with questions instead of bothering him at work.

[@Deviant365]

@@superminer66 These muppets have been told repeatedly not to call him, but they continue because they all want specific help with their vehicles. The SMA community could help each other and Eric out and hopefully cut down on the calls.

[@briantii]

I actually think there maybe a missed opportunity here. "Remote diagnostic consulting" or something like that. Phone based and billed at $15 a minute or something. Done correctly it could be very useful for those desperate for his awesome skill set (which is virtually impossible to find) and could be a good profit center. Would have to figure out pricing - but reserving 30 minutes a day for consulting services might actually make some sense.

[@mph5896]

​@@CALVINLNIKONT When he said don't call me at work don't call him. He even left a message saying don't leave a message.

[@CubasAutomotive]

@@briantii waaaay too busy to deal with that. Plus working on a vehicle remotely is not advisable, especially if the person asking for help is clueless to begin with. It's not the same, not touching, seeing, hearing a vehicle in person. They have forums & cars "just ask" sites for this exact thing. Too many liabilities added with a "hotlines"

[@warrend114]

Hey Eric in the future you can put fluid film on both posts before install to help prevent corrosion

[@norseironworks]

Clever design. Sooo when you need to hook up a battery charger in wintertime or need some start cables from another vehicle you just have to jack it up, remove lots of parts. Clever, very clever

[@m3rdpwr]

Glad I didn't have to replace the battery in my 300M before I traded it in. My New Frontier, the battery was junk in less than 3 years, maybe 18k miles. Brake rotors rotted out in Frontier shortly after, too.

[@zeropointzero]

I just did one a few days ago. Had to replace both terminals because they fell apart as soon as I touched them. The Mopar/Exide battery lost its fluid everywhere. And btw, to avoid sparkie sparks and wiped out ecm's, I disconnect the negative cable lug under the hood. ☺

[@ericsplan1]

Hope your feeling better today

[@petemedina8446]

These are pain in the rear to do stupid chrlslet. I'm actually surprised there wasn't that green corrosion all over the cable ends as sometimes there is. Glad you cleaned the cable end and sprayed it that should keep corrosion off for while

[@tonythediyer8537]

Glad to see you got over the dropsies. ;)

[@SouthMainAuto]

must a been a 24hr thing.... drained me man 🤢

[@AntonioClaudioMichael]

Great job and video Eric O

[@BADD400]

Good video Eric

[@elmecanico4943]

Very professional.

[@jordangreene5243]

I work at advance auto and we do not install batteries on those. It'll actually tell us in the computer when we look up the battery for the vehicle "professional installation required". At that point we just have to refer them to a shop.

[@toysareforboys1]

I like having my battery in the trunk, you can put in any size you want, no restrictions :)

[@langer24106]

toysareforboys Miata?

[@tiredagain6722]

New SMA swag...wrench condoms. For those times you feel the need to unhook the positive terminal first!

[@baddabing4609]

So remove half of the front driverside to remove/replace a battery... Solid engineering ^^ My good old saab got two bolts, replaced in 2-3 minutes time.

[@k0rndog93]

My car has a bungee cord and a 5/16th bolt for the terminals. Easy peasy lol

[@RyMann88]

Most hondas are just as easy. Used to hate Chevy Cruze batteries because of the weird hold down set up, but they're stupid easy also if you know the trick to getting that hold down off (pro-tip, just use a screwdriver).

[@mikechiodetti6737]

Been There Done That. Still a Great Video!

[@ramdodgetruck]

In a previous episode, Eric said the battery is ten yrs old. Chrysler figured you would have junked the thing by now, hence, put it somewhere you'll never see it. Also frees up space in the engine bay.

[@robertsise7898]

Ok. I posted on the last video about this before seeing that you have performed this lovely repair. Bet you dont get free installation at the local Autozone eh?

[@bobl78]

the also could have placed it inside the oil pan or welded somewhere in the chassis... so we`re happy with that Are you feeling better? Upper and lower main seals are tight again ?

[@mikefedele4521]

That dodge looks decent not all rotted out like up here. I coat cable ends too. I've been using the muscle grease from castle I found it conbats the salt and brine pretty good it seems to hold up best so far. That and rottten starter relays/fuse boxes..... 👍

[@SmittySmithsonite]

Hmmm ... SMA frisbees! Just got that idea looking at the hub again. 😉 MAN! Automakers make me mad. Batteries in the trunk, under the rear seats ... and now in the FENDER WELL?? Geeze Louise!! What a fantastic spot for Northeastern vehicles, right in the salt blast. Fairly certain that plastic liner ain't gonna do S!&$ when you're rolling down a slushy, brine and salt-laden highway at 50+ mph. It'll just sit on the battery terminals and work it's crusty magic. BRILLIANT. I can just see a group of engineers around a table playing beer pong, and designing this turd, when someone goes, "Aww s!&% ... we forgot about the battery!" " Ahh, just stuff it in the fender - it'll be fine for the warranty period". 😡

[@GNX157]

Harbor Freight sells composite material 1/4 and 3/8 drive shorty ratchets you could use for that positive terminal.

[@parochial2356]

Not sure if the old one was OEM or aftermarket, but somebody was not thinking when they put in a battery that would need periodic water level checks. How many times do you thing the level was checked? May be bone dry, necessitating this replacement video. Bravo to Eric for putting in a sealed unit, as should have been to start with.

[@user-zt4ry9hm9u]

Pretty much all car battery's are sealed, haven't seen an open celled one for sale in over 10 year's.

[@rayg9069]

@@user-zt4ry9hm9u Still popular after market in Australia where temps kill sealed batteries

[@KalebKronic]

I've seen the trunk mounted batteries and the ones you get to through the passenger footwell(Ferrari IIRC), but this one was new. So glad all my vehicles have had them in one of the front corners up top where they belong. Guessing that car would be a real PITA to jumpstart.

[@terrystoner4504]

Wonder what the battery gestapo would say to jump starting a Cedar Rapids paver with a arc welder? Yeah that happened and I moved the controls to the other side of the paver from the battery to start it.

[@AP9311]

Wonderful video. But hate that battery location!!! Ugh. But that fluid film needs its own intro!! Like a toot or ka ching!!! :) look forward to the next part :) stay warm, my friend!

[@kellyspeppers]

Not the only cars Chrysler put the battery in the wheel well, recall Plymouth did it also. I tape up tools with rubber splicing tape to use on positive battery posts.

[@nicholasgamble4643]

I've actually pulled the positive post first not a good idea but in a pinch it works

[@lesbender236]

With a minimal amount of brain power,they could have put the battery in he other way around so the negative would be the one nearest .In a crash which would probably ground the front one first,it wouldn't matter because the whole thing will be smashed anyway causing acid to be every where and a fire would ,more than likely result

[@davids8956]

At the 10:00 minute mark If you read the fine print it says Advance installs batteries on MOST vehicles. Something people aren't too happy about when they come in and to have a battery installed and find this out.

[@MrStephencartwright]

You can always use a set of electrically insulated wrenches (spanners) that you can get from your local electrical component supplier and they're good for a 1000volt

[@February54]

I did a 2015 Ford Escape battery once and you HAVE to disconnect the positive first. Then you can slide the battery out of it's hole and get to the negative. If you can, always do the negative first, but if you can't, don't worry.

[@sbellock5]

It seems sometimes that the people who design cars either don't understand or don't care that it will someday require service. As a side note as someone who went to NIU, I love the bag of DeKalb corn behind you.

[@donnierobertson3088]

Great job again A+

[@davidostring7627]

Thank you for showing this video, now I know what car not to buy!

[@franknewling1139]

Back in the '60s and 70's, my brother had a gas station with service bays. I don't know what brand, but he had a nice little set of wrenches (5/8 to 3/8, I think) with some kind of coating on the handle shaft and a nice little box to keep them in. He liked to call them his "electric" wrenches. Fancy! He made the purchase after welding a watch band to his wrist. He still has the scars to prove it!

[@markwheeler202]

Were the cables long enough to allow the battery to be flipped when reinstalled? That would place the negative terminal on the near side.

[@dgecse]

What a convenient location for the battery! At least it's well protected by the bumper skin... seems this location could result in a minor fender bender turning into a disabled vehicle!

[@wanderingmercurymarauder761]

If it's a minor fender bender then the battery will be fine.

[@ozzstars_cars]

I need a toot of Fluid Film. I have some crusty nooks and crevices.

[@thewt]

Used to have a printed list of cars we can't put batteries in. Now more often than not that information is found in our parts catalog. In the description of the battery that the car needs.

[@upallnight888]

Wow, a cliff hanger video, I'm on pins and needles waiting for the check valve video.

[@edd6113]

If you get sparks, it's just the car letting you know your doing a good job! Think the designer should live on the shelf where he put that battery!

[@stevemartinez1909]

I bought an AutoZone battery before it lasted two seasons I learned my lesson I only buy interstate batteries I went out of my comfort zone never again

[@justindavis1192]

Good stuff !

[@justindavis1192]

I have done this job before on the avengers . And no autozone nor advance would touch it . At the time I couldn’t find a helpful video . Personally when I did it I was able to reach in with a ratchet and do the ground first with battery slide a little . I was paranoid about grounding out my tools . Next time I’d just go your route and be careful . Good stuff . I think you should start doing the year range of the vehicle so people use it for specific searches . Might raise your following ! Good work

[@deanh7190]

Advance Auto free batt replacement...was just thinking that too. Hmmmm.

[@ScooterVille1971]

Afraid not, we at Advance Auto can not install this type of configuration. Prior to purchasing the battery we would inform the customer that the install can not be performed by us due to it's complexity. Our in store look up flags it as "need profesional installation".

[@stevemartinez1909]

None of them auto stores put that battery in in that car in most garages charge you $50 25 to take it out in 25 to put a new one in just labor I know I got a 2008 Dodge avenger the first battery I bought I had the garage put it in and that's what they charge me for labor $50 plus the battery

[@LrdnBeast]

When I first started at Advance I attempted to install one. No power tools in the rain but had to stop because of a tornado... Lesson learned 💩

[@robertevans6481]

I was thinking that just as he said it....funny thing is I bet they open the hood and then ask the customer, "where is your battery at" Lol

[@bigb7157]

Spent 15 years at advance auto. Definitely did a few of these. Still easier than the Chevy vans with sideposts facing inward under the brake master cylinder with both positive cables corroded together.

[@jdtractorman7445]

I had a 98 F-150 back in the day that I did not have to change the original Motorcraft battery until almost the end of 2007. 10 years old or pretty close to it.

[@oolague6197]

Good job chrysler🖒🖒

[@alphaod]

When you put the replacement battery in, couldn't you have put it in the other way around so whoever does the next battery replacement can removed the negative terminal first? Or are the cables too short?

[@danieldyer1]

I remember my father working on a battery in a GMC 1/2 ton truck. He was taking the positive off first and drew a spark off the metal ac line, opening a pinhole leak and all the freon escaped!