Dodge Charger - AIRBAG & SRS FUSES LOCATION (2011 - 2021)

[@gangstalkingsimulation1319]

So did u remove the fuse

[@diegoc1326]

I have a cop car too but i put the regular seats from a rt and my air light bag is on ima check those fuses and hopefully my light turns off

[@QuiteAlright]

Did you disconnect the battery before replacing the seats and did you maybe try to start the vehicle while seat was disconnected? If you did you will need a scan tool to erase the airbag codes. If not then definitely first check the fuses and then double check all connections and wiring under the seat

[@3Dirty8]

I have the same issue I have a SXT '20, put new seats from a 23' RT and those seats come with a second grey colored1 harness and the yellow harness which connected fine. Yet my 'air bag light' is on Is the second wire harness the issue Or Do my yellow harness not match seat wiring As I tried a '14 as well and realized the pins on yellow harness is different placement (as it disabled my outpark and did not match pressure sensor)

[@3Dirty8]

I have the same issue I have a SXT '20, put new seats from a 23' RT and those seats come with a second grey colored1 harness and the yellow harness which connected fine. Yet my 'air bag light' is on Is the second wire harness the issue Or Do my yellow harness not match seat wiring As I tried a '14 as well and realized the pins on yellow harness is different placement (as it disabled my outpark and

[@QuiteAlright]

Hi not really sure I can help with this one. 14' is pre face lift so it shouldn't fit. 15' and up should fit but there is 6-7 different combinations of seat options and you have to match the right one. For example if your factory has memory seats, heated seats, 6 way adjustment or 12 way adjustment. And RT probably has more options and i would think this is the problem. Now if that would trigger airbag light I don't know, possibly yes

[@elpatrondelmal2261]

So if I remove the fuses did it go away ?

[@QuiteAlright]

No it won't. Only way to take care of it is to diagnose what is going on and fix it. Scan the vehicle using higher end obd2 scanner to get the codes and follow up on those.

[@dmorales74]

My light goes on and off randomly. I’ve checked the plugs under the seat they seem good… would the fuse bring out make it go on and off?

[@QuiteAlright]

No, bad fuse would cause the light to be on all the time. You would have to scan the vehicle while the airbag light is on to get the code and that will point you towards where is the problem. Could be a lose connection somewhere or even a failed sensor, doesn't have to be the one under the seat

[@dmorales74]

@@QuiteAlright Thank You I checked fuses and connections everything seems good. Guess I’ll have to scan it

[@QuiteAlright]

@@dmorales74 That's the best you can do. Let me know what was the code

[@leri3365]

​@QuiteAlright my light is on as soon as car is on and no code from check engine. Replaced fuses and looked underneath seats. Wasnt in any accidents

[@MinooandMockey]

My fuse is always on and the code is B276413, its says the Right B pillar impact acceleration sensor circuit open, i have no idea where is it and how to fix it. Any help is appreciated. Thank you so much!

[@QuiteAlright]

Pillar B is located between front and rear door. You have a code for the passenger side. So you will have to remove plastic cover on top of the pillar to get to the impact acceleration sensor. You want to inspect wiring and especially connection at the sensor. You are dealing with either damaged wire / bad connection or sensor failure

[@MinooandMockey]

@QuiteAlright so on the right side between the front and rear, I have to check for the sensor there correct?

[@QuiteAlright]

@MinooandMockey Yes that is correct

[@MinooandMockey]

@QuiteAlright do I need to take off the panels from the inside or the outside panels?

[@QuiteAlright]

Inside panel. You will have to remove the pillar panel between the door and sensor should be there somewhere. I've never done on Charger so can't tell you exactly. Code points towards it. Often the connectors need to be cleaned and reconnected