DRIMASTER ECO INSTALLATION

We will guide you step by step installing the unit and looking at compatible accessories. The simple installation for Drimaster is fully compliant to building regulations and only requires minimal maintenance.
For more information click here: goo.gl/jRv8Jl
IMPORTANT NOTES TO INSTALLERS
Successful operation of the fan depends entirely upon the unit being installed strictly in accordance with these instructions. Please follow step by step to ensure a satisfactory completion.
Whilst the installation of the DRI-ECO-LINK-HC unit may be achieved by suitable persons, the provision of the electrical supply and the connection of the unit to the mains must be carried out by a qualified electrician.
Warning: Isolate from power supply before removing any covers. During installation/maintenance ensure all covers are fitted before switching on the mains supply.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances.
Means for disconnection must be incorporated in the fixed wiring as shown in the wiring diagram in accordance with IEE wiring or national wiring rules.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
LOFT INSPECTION
Check to ensure that the loft has adequate ventilation. There may be occasions where a loft is so well sealed that additional ventilation may have to be provided by the owner/occupier.
Ensure that all water tanks are covered and sealed.
Check that all water pipes are lagged.
Ensure that any extract fans are discharging to outside and not into the loft.
Check that the loft hatch is tightly sealed.
Ensure that all holes in the ceilings are sealed i.e. ceiling light fittings etc. A visual inspection of any flues or chimneys for leakage in the loft should be carried out by the installer.
If any leakage points are found, or if there is any doubt at all, then the installer should advise the house owner/provider as soon as possible and seek instruction from them before proceeding with the installation.
For more information click here: goo.gl/jRv8Jl

[@mcc9887]

Thank you for putting this on it was very helpfull iv just fitted one ,i think more people will be fitting these as time goes on.. but will have to give it a week to tell how good it is....but many thanks for this

[@nicoskakoullis9901]

Great video to use for installation

[@SS-go7yr]

Thanks for the video. I have a question regarding safety of using PIV's. I have loose Fiberglass loft insulation and I am wondering if it is safe to install one in my loft? The fiberglass particles are certainly unsafe but maybe the filters will do the job? Many thanks.

[@isells]

Thank you for your question and valid concern. Drimaster unit could be fitted with NOX filters see video for more info kzbin.info/www/bejne/q2jKeHuKn65gmbM or visit our website: www.i-sells.co.uk/Search-Results?keywords=drimaster+nox

[@zabotage]

When you say loose? do you mean the "blown in" type or is it in rolls? I'm also interested in this and wonder if you installed one and how you find it?

[@tomohall2510]

I’m trying to set up Drimaster 4 way switch with my nusire drimaster dri eco heat has model I bought from you guys The machine won’t go into binding mode while I’m holding both up and down buttons for 30 sec. A u symbol comes up rather than a line Any idea what I can do

[@isells]

Hi Tom, Thank you for your query. Do you have the Installation Manual for the unit? If not, these can be found on our website on the product page, if you scroll down to the section where it says "Downloads" and you should see the Installation Manual listed there. If you have trouble finding it, then please contact us directly and we can email you one. If you have model DRI-ECO-HEAT-HC, then check out page 6, section 7.7 "Binding a sensor" - it gives some guidance to follow if the binding does not occur. If you try that, see if that helps. If not, please contact us directly and we'll help further.

[@Rc-hb4vr]

How can I attach ducting to sit over the fan correctly

[@isells]

Hello Rosario, Drimaster uses a 200mm flexible hose. This can be connected using hose clip: bit.ly/200mm-Hose-Clip if you require additional assistance please call 02084639696

[@adivicica807]

Hi, I have issues with my PIV, it is show 0 when switch on. Could help me ?

[@isells]

Its probably the setting your unit is set to. Have a look at this video: kzbin.info/www/bejne/ZnrThoV_o9Kilas or give us a call 02084639696