I have the same issue "drivetrain" on my 2015 650i, and the car shakes. I scanned and it says missfire in cylinder 4, and injection switched off. Can you help and let me know from your experience what is the cause? Is it coils, spark plugs, fuel pump, fuel pump relay, injectors etc. Thanks.
@raazrazdhan27222 жыл бұрын
Today I went to buy a used bmw 5series 535i. And while giving the full acceleration I saw this message pop up. “Drivetrains, drive moderately” full performance not available “ Can you please help me out. Should I buy this car with this issue. Is this a major problem.
@engineeringinvestigation62082 жыл бұрын
Get it checked. This message only means that there is some problem on the car when you drive it in full throttle.
@victoralonso53194 жыл бұрын
Thanks bro good video
@damanpreetsingh67115 жыл бұрын
Hi...sir....my car is showing this problem. And its shaking while i start. Is this problem in plug.? My car is vibrating while moving.
@engineeringinvestigation62085 жыл бұрын
If your car is shaking after you start. Then it may not be spark plug. Please do a full diagnostics and see the codes first.
@bukooo793 жыл бұрын
Hi there. I have similar problem .The error shows up only when I turn off the engine.the car working OK . I brought the car to dealer and no error show after diagnostic run. Have any idea what can be. Thank
@bukooo793 жыл бұрын
"Possible to continue journey. Have the problem checked by sevice" this is the error showing on bord
@engineeringinvestigation62083 жыл бұрын
No error comes up? That's strange. If its misfire. Then it will be registered in ecu as a stored fault
@franklinwatson77675 жыл бұрын
I have the JB4, and I got the drivetrain malfunction do to running Map 7 with a E85 blend. Map 7, according to burger tuning must be ran on 100 octane race fuel. went back to Map 2 and everything is fine.
@engineeringinvestigation62085 жыл бұрын
At map 7. Whats the max boost? Is it above 24 psi? If the drivetrain came and if the fault code says that its misfire? I really like to know what gap you are using for your plugs?
@kimchenghong74604 жыл бұрын
Hello
@kimchenghong74604 жыл бұрын
Hello I have problem with my car Bmw i8
@trustgtr335 жыл бұрын
name of channel is misleading..best is to rid of the car, push it of a cliff...
@thefaceofq73745 жыл бұрын
Many BMW forum members have mentioned cause as either bad fuel injectors or spark plugs/coil pack. Good luck!
@gohalos264 жыл бұрын
Having the same problem on my f10. Replaced coils and plugs since I was at 75K miles anyways...but still having drivetrain issue. Happens only on hot days when I'm accelerating
@engineeringinvestigation62084 жыл бұрын
Please scan the car and see the dtc codes. Make sure its misfire or something else. Then we can get an idea about the issue which cause drivetrain error
@myagmarlkhagvajav15974 ай бұрын
F10 fe full performance not available. continue the journey at a moderate speed. have the problem checked by service
@chrisfinta49413 жыл бұрын
I had the same issue yesterday 01/16/21. My cylinder 1and 5 spark plug ceramic cracked half, don’t give any spark . We put 6 new one and running great!
@pekay265 жыл бұрын
I just took delivery of an F90 with 40 miles. Got this error. Back to dealership it goes.
@phillyaccord56354 жыл бұрын
Paul Kim damn man that sucks! What happened next, did they fix it?
@Rockbottomconcreteca4 жыл бұрын
My car has been having this problem for a few weeks now , took it to a mechanic and he said it wasn’t having any misfires , he didn’t have the right scanner to tell me exactly what it is . Do you have any idea on what you think it is ? the drive train malfunction error pops up every time I accelerate thanks in advance
@Rockbottomconcreteca4 жыл бұрын
I have a 2011 535i , like I said he put a scanner on it and it didn’t read any misfire codes she said . What else could it be ?? Stressed out man
@swapnasunil3156 жыл бұрын
Wow ..this thing is really informative. .keep uploading more dude
@Planetyt14 жыл бұрын
Hi there got a bmw 535d diesel 299 hp 2010. if the loss from the stand comes this warning message, what does that mean? (Full drive power not available) the message goes away when the vehicle is at a standstill and switched on after the engine has been switched off My question you know what has to change 👇🏼 1-glow plug control unit? 2-EGR valve? 3-oil transmission 4-oil filter
@ishaielaluof3 жыл бұрын
??
@sadiarehman73932 жыл бұрын
For me, I replaced the oil filter and it worked
@mateimarianlucian7412 ай бұрын
Are dpf peste 50 de grame infundat ok.
@CS-hh4it2 жыл бұрын
I have a code named p00bc n it says about my mass air flow sensor but I can’t tell whether it’s my sensor or the cable connected to the sensor n i keep getting drive train malfunction when I step on the peddle a bit deep
@CS-hh4it2 жыл бұрын
How can I tell whether it’s my sensor , the cables or a leak
@mattbrown11654 жыл бұрын
Interesting video. I have a 2015 X5 M, 32k miles. Last week I received that same message and the car started to shake, steering wheel, break pedal. When I stopped at the red light, I noticed it was idling at around 1200, it idle at about 650. I called my local BMW dealer as I bought there new, with an extended warranty. I drop it off in two days. They are giving my a loaner car and my service advisor said they would need the car 3 days. Does that sound right? By the way, I was going about 25, just changed lanes and had accelerated to around 55 when I got the message and felt the shaking.
@engineeringinvestigation62084 жыл бұрын
Any faults on the ecu will trigger a drivetrain message on screen. Its always better to do a scan inorder to see the faults registered. If its p0300 or 301 till 308.. then its a misfire. And changing plugs solve the issue is most cases. But... at the same time.. there are multiple reasons for misfire.. starting from plugs. Coil. Injectors afr etc... let the dealer check and see what did they find.
@wheymonster4 жыл бұрын
I have this problem 'Drivetrain: Possible to continue journey. Full performance not available. Have the problem checked by your service partner.' My cars a 135i, no signs or obvious problems. I haven't driven the car hard at all for a few weeks and it's in good service. Can you help?
@franklinjunior98128 ай бұрын
friend, I have a BMW 430I with defect code 164040 intake shaft control adjustment with error.. 130E11 camshaft intake valve control signal not plausible
@soudalbattashi87764 жыл бұрын
Hello, I have the same broblem, on 650i 2014,, but once I restart the car and close open the door again,, the car is going back to normal, I took it many times to the dealer in the last 3 years but still comming back, every time I race,, also the car is already out of warranty, I don't know how much this could cost me,, what's your suggestion please,, thanks alot dear
@engineeringinvestigation62084 жыл бұрын
Sure. Let's figure it out. I think you contacted me via WhatsApp
@umit3072 жыл бұрын
Hi ,i got bmw 2015 535d f10,i was on holiday in turkey ,i drive from uk to turkey,on the way back i sow on screen this problem ,4 times on the way i drive 4000km non stop ,now screen dosent show anythink ,can i take dealer or not ,drive fine everythink ok
@MRROBBIEWATTS5 жыл бұрын
Very good Video - Thank you - :)
@ChipZilla694 жыл бұрын
I've got an M240i with the B58 engine. It's due it's first service in two weeks time and done 8k miles. The car has been perfect but I just took it out the driveway and I got the Drivetrain malfunction error and the car was misfiring causing vibration through the vehicle. I've called out BMW services as the car is under warentee thankfully, hopefully it's something simple with the fuel line, electrics or sensor.
@4444nig43 жыл бұрын
I have almost the same issue. What turned out to be the problem?
@ChipZilla693 жыл бұрын
@@4444nig4 they blamed a faulty injector replaced it and have the car back. Seemed fine until first time doing hard acceleration and it happened again. Turned out to be a faulty cam cover leaking coolant and that's what broke the injector. They had the car for six weeks i think trying to work it out.
@4444nig43 жыл бұрын
@@ChipZilla69 shit, 6 weeks are a very long time. But thanks for your answer, that might help 👍🏼
@USABOSS3574 жыл бұрын
hello Can you please give an advise what does this code mean and how to solve it..2013 BMW 328I XDRIVE ..120408 Status history boost presure control: shoot down as a consecutive reaction !!! - 131908-VANOS inlet: cold Start Position not reached !!! I found the answer: upgraded the software using Ista problem solved!
@il3galburnout1572 жыл бұрын
The same thing is showing on the screen in my bmw f10 530D please tell me what exactly is the problem.
@Darild.Peters3 жыл бұрын
I had this and car started shaking out of nowhere , turned off and turned on car and was running perfect, no codes popped up either ??
@sufyankhan33346 жыл бұрын
I am getting codes on my 2013 640d 83k miles 244C00 charging pressure control charging pressure to low 27b900 exhaust back pressure sensor before turbine signal deviation to calculate exhaust pressure too low . Its only dose comes on when i put my foot down and dose got away it self
@engineeringinvestigation62086 жыл бұрын
Seems like you have multiple problems. Check boost pressure. Check Wastegate actuator. Check exhaust valve if you have. Check compression on all cylinders. Then only I can say anything.
@sufyankhan33346 жыл бұрын
@@engineeringinvestigation6208 i spoke to bmw recently and the said there is a recall regarding gass pressure or something i dont exactly remember i will call them again thanks for your time
@abrahim48615 жыл бұрын
I have the same message in my BMW 5 series F10 535d m sport 2011, I lose some power and I'm not sure if the old owner have replaced the glow plugs/coils. but then when i tern the car off and turn it back on the sign is gone!!! what will be it? if any one know please let me know.
@andymitchell3685 жыл бұрын
Abrahim I have a 2010 535d gt I have the same problem the car has full history I’ve had the engine out twice anyway I’m now being told it’s the turbo’s lol I’ve had 39 BMW’s but this has me stumped good look 👍
@abrahim48615 жыл бұрын
I just found an air leak, I bought some parts to get it fit and hopefully that will be it mate, but when the car was with BMW thy have reported that i might will have a problem later in the turbo.
@lungamabele20143 жыл бұрын
Thnx for this video,,mine is a m135i, I parked it for almost a month while I was away..when starting the car the drivetrain malfunction came..its not shaking, nothing...only no power
@kalps692 жыл бұрын
It happened on my M4, but the transmission was skipping gears 2,4 and 6. Basically the car is fucked. Coupled with a leaking turbo I gave up and traded in
@engineeringinvestigation62082 жыл бұрын
It was a bad decision... its dct gearbox. You should have replaced the clutch. Leaking turbo is causing while smoke?
@henryduran52065 жыл бұрын
Thank you for the video, my bmw 528i xdrive shakes and the drivetrain malfunction comes on when I try to speed up a bit. When I shut off the engine the error goes away and then returns when I try to pick up speed quickly. The codes I get are 120308 and 138701. Can you please help me out on this?
@United-Solutions Жыл бұрын
Hi It might be for solenoid coil and break vacume pump or diverter valve need replac
@michaelatmodihardjo89975 жыл бұрын
Hellow im michael from indonesia, im having alot of problems with my F10 M5, could u please help me? By email or whatsapp? Thank you!
@engineeringinvestigation62085 жыл бұрын
Sure. My WhatsApp number is +97431022031
@marioguzza20953 жыл бұрын
I have the same problem and on x5 25d f15 2014. continue the journey at a moderate speed. Full performance is not available anyone know how hats going on losses the POWer only have 57k miles
@engineeringinvestigation62083 жыл бұрын
Please do a full obd scan and let me know the fault codes
@zinidishi72593 жыл бұрын
Hi. Today happen to my BMW 520d F10. Drivetrain car is protected and it slowed down couldn't accelerate what it can be ? Thanks
@itubetube962 жыл бұрын
Did you manage to solve the issue and what was it ?
@shakielmhd3 жыл бұрын
Hi I have a bmw 116i sport f20 it has drivetrain fault come up I have had the valvetronic replaced and the ECU for the valvetronic but still no luck main dealers bmw are saying it needs a new ecu ? Any help would be appreciated
@engineeringinvestigation62083 жыл бұрын
What was the problem with valvatronic? Is the step motor or shaft problem? After replacing. Did you do the adaptation and calibration for the valvatronic? What fsult code made you replace the valvatronic system? Which year is your car.
@shazyshaz5023 жыл бұрын
My bmw is f30 320i when I start it makes miss fire and after 30 seconds it goes smooth by itself what could be the problem even I change the plugs
@engineeringinvestigation62083 жыл бұрын
Seems like rough idling. Did you check the maf sensor?
@TheUmeru6 жыл бұрын
I have a list of errors as well. can you help me identifying the fault please.
@engineeringinvestigation62086 жыл бұрын
Let me try bro... give me a brief about what you have done. What problems you have right now and errors you have on the car. This will help me to understand it better
@TheUmeru6 жыл бұрын
Hello, I have these below list of errors, I hope you would help me out. there is a jerk at idle and the guy told me there is a misfire in cylinder 1. 140001 Misfire, Several Cylinders: Fuel Injection is switched off 140002 Misfire, Several Cylinders: Damaging exhaust gas after starting up 140004 Misfire, Several Cylinders: Damaging exhaust gas 140010 Misfire, Several Cylinders: detected 140101 Misfire, cylinder 1: Fuel injection is switched off 140110 Misfire, cylinder 1: detected 150C11 Misfire, cylinder 1: Combustion period outside tolerance
@engineeringinvestigation62086 жыл бұрын
@@TheUmeru hello bro. Have you checked the spark plugs? Ignition coils? Is the misfire only in cylinder no 1 every single time? Or is it random? I like see know how the plug looks like. Swap ignition coil. If you still have misfire on cylinder 1. Then do a compression test. This will give me further idea on what to check next.
@sajjad.m.abdulganny6 жыл бұрын
I have the same problem bmw f07 . I don't know what I have to do.
@engineeringinvestigation62086 жыл бұрын
@@sajjad.m.abdulganny sorry for the late reply bro. What faults you have it on your car?
@williammathipa5875 жыл бұрын
I had the same problem with drive train, i replaced the turbo and now it has started again
@Ahmed-J7873 жыл бұрын
Same thing been told to me by my machinic . I have changed my plugs and coils the problem solved for few days then again it happened. Then I went to machinic he said change turbo .. as it has a leaking ..but he said may be some other issue also in engine head ..so better sell it .. it will cost you more to fix all these issue ..no sure what to do . Car only give drive train when you srat the engine in morning.. and it shakes also ..After that it become fine..
@HabibiThaal3 жыл бұрын
👍
@VenkateshN-eb2hx Жыл бұрын
Thanks for the video, i am getting the same warning message intermittently - Gave car to local garage and they said everything looks fine but I still get the same warning when I start the car(it vibrates and shuts off). BMW 116d m sport 2013 model. Would be great if you can share your experience on this.
@engineeringinvestigation6208 Жыл бұрын
I am not an expert on the diesel engines. I will recommend a complete software scan to get an idea
@VenkateshN-eb2hx Жыл бұрын
@@engineeringinvestigation6208 thank you and thanks for the prompt response :)
@calebmedleyiii80286 жыл бұрын
thank you, I hope that is the fix in my case. My seems only to happen under heavy acceleration.
@timatinaj14186 жыл бұрын
CALEB MEDLEY III bro can u update what happened with your car and what how did you fix it cause my car is having the same issues
@thesolution3576 жыл бұрын
Taymoure Naji Naji after it happens after you restart the car. If you restart like he says and everything is fine... you still need to go get the codes read. I believe mine are the O2 sensors and probably spark plugs. I still need to fix it, mine only happens when I drive really hard so haven’t fixed it yet, but I don’t believe it’s anything too serious
@medusapicture68265 жыл бұрын
I lost torque on my Diesel 328d 2018 :((((( gas is not responsive anymore, car slowly and smooth accelerating:(((
@d0218douglas5 жыл бұрын
Just happened to me, I thought i broke my car , it was shaking bad at the red light after I floored it.
@wanwann95303 жыл бұрын
@@thesolution357 have you fix the problem?
@eriakiyemba93254 жыл бұрын
After changing bearings I have the same problem what could this be ?
@alex_rpm4 жыл бұрын
I have a f31 what is it? Is not M Power!
@santhoshwilson22065 жыл бұрын
Hi my car shown the same today, it’s 2014 bmw 5 series m sport, but when I opened the door and closed it and run a status check up it shown no faults, the problem shown when I accelerated abruptly. My doubt is if I run the system checking with garage can they find out what’s wrong
@testosteron43995 жыл бұрын
Santhosh Wilson if its a diesel, than probably EGR and EGR COOLER!
@bitcoinchannel77235 жыл бұрын
My BMW F30 problem same Coil Plug problem tq sir share information
@miamitreasurehunter6 жыл бұрын
Thank you for posting this I had the same problem
@kingbvlogz71724 жыл бұрын
I have a 2013 650i gran coupe and it just started doing this
@engineeringinvestigation62084 жыл бұрын
Please do a full scan before conclusion
@alex_rpm4 жыл бұрын
I have a f31 what is it? Is not M Power!
@patrickedwardbassett72284 жыл бұрын
How did you diagnose the problem like that on 1:49?
@wahedminnas75233 жыл бұрын
Good
@danieldejesus8663 жыл бұрын
I have that error code and i replaced plugs and ignition coil. It ran ok before and now that i did that changed the plugs and coil it’s running bad and hesitating. What can cause that?
@engineeringinvestigation62083 жыл бұрын
Please do a obd scan. Lets see the codes first before we proceed
@danieldejesus8663 жыл бұрын
@@engineeringinvestigation6208 system to lean bank 1
@c.k.menamena35013 жыл бұрын
We did the same exact thing changed the spark plugs and a day later getting the drivetrain error. Just paid over 3k in the shop got car back the other day and error is back. They didn’t even bother to check the spark plugs or coils even after I told them this problem happens after changing them
@danieldejesus8663 жыл бұрын
@@c.k.menamena3501 wow that’s crazy. I’m going to take it shop next week and see if they can figure it out.
@992turbos85 жыл бұрын
Why are you using someone’s else’s Channel name
@engineeringinvestigation62085 жыл бұрын
Yes. Thank you for informing me. I will be changing my channel name to a unique name.
@readmore41784 жыл бұрын
What scanner do you use?
@engineeringinvestigation62084 жыл бұрын
I have ista for bmw. And autel for all other cars. Autel also works good for bmw as well
@readmore41784 жыл бұрын
ENGINEERING INVESTIGATION Thanks. Will look into. Does it require only a cable? Or a handheld scanner?
@zakiranderson7225 жыл бұрын
Got to 2:30 too painful gonna look for another bye
@testosteron43995 жыл бұрын
@ENGINEERING INVESTIGATION I Have a big problem with my f01,740d 225kw/306 ps , 6 speed. This error is coming and going for the last 28 000 km and no one can find the problem. When error occures(every 10 days aprox.) car jerks in LOW rpm’s. And one more hint, i noticed it consumes coolant fluid. My mechanic at the latest, said it must be EGR COOLER fault. Because it shoots coolant into the engine by fault
@engineeringinvestigation62085 жыл бұрын
On new m3 and m4.. i have found faulty intercooler. So what happens is.. the coolant is leaking from intercooler to engine. This will cause drivetrain and engine jerks in low rpm. But in higher rpm the car will run fine. Please check the compression on all cylinders. This will give you a start...
@hamzababli6785 жыл бұрын
I really have a question now, I’ve been changing the spark plugs and the ignition coil in my car but the light of the drive malfunctioning still on and it still taking much of gas. What I have to do? Please. Thank you
@engineeringinvestigation62085 жыл бұрын
Seems like you have drivetrain error caused by some other reason. Not misfire. Scan your car. See the fault codes. And find out the reason for drivetrain. Solve that problem.
@hamzababli6785 жыл бұрын
When I change the spark plugs and the ignition coil they was very bad and dirty, I changed them but the picture of the drivetrains still on, do you have any idea to do?
@BullyChicken5 жыл бұрын
I think it might be wiring. I have same issues with my 2013 x3 it pops up everytime but i do not notice any loss of power. I just hit the acnowledge and it goes away.
@engineeringinvestigation62085 жыл бұрын
@@hamzababli678 please do a diagnosis and find out the fault codes
@thefaceofq73745 жыл бұрын
Check for bad fuel injector(s)
@nitheeshvakkekattil99346 жыл бұрын
👍
@engineeringinvestigation62086 жыл бұрын
Nitheesh Vakkekattil i need to make it more better.
@simplelangperorock5 жыл бұрын
Could The Timing chain on X3 a problem?
@LeamsiLolGamer5 жыл бұрын
Hi! I have the misfire and the switch off fault! I changed coils and plugs but still the error on the 7 and 8 cylinder. What should i change? It an SOS question. Thank you for your answer.
@engineeringinvestigation62085 жыл бұрын
Is it always 7 and 8? No other cylinders have any misfire? If its only 7 and 8 and always 7 and 8. Then you must check compression. If its ok. Then check fuel injectors.
@LeamsiLolGamer5 жыл бұрын
@@engineeringinvestigation6208 yes its always 7 and 8. Those Two cylinder are not working. The compression is 12 bar
@engineeringinvestigation62085 жыл бұрын
@@LeamsiLolGamer check the fuel injectors. Try to turn on and off while the car is running. There is option for fuel injector cut off using diagnosing tool.
@LeamsiLolGamer5 жыл бұрын
@@engineeringinvestigation6208 is it possible that it is ecu problem? The left cylinder row is absolutly not working. One ecu fuse was wrong but i replaced it and nothing changed.
@maksczarnota93223 жыл бұрын
@@LeamsiLolGamer I have the same issue (BMW 760i N74 engine) All 12 injectors, plugs, coils, changed, compression is around 11.5 bar on all cylinders. After full cold start when car drops to 650rpm and starts to shake and show Drivetrain malfunction issue, after 2 minutes running when restarted its gone (the message) but still car is shaking and rough starting on 1 gear and reverse. Normal driving, accelerating after that is perfect no shaking no power issues nothing at all, only when standing still and up to 10km/h. Please help someone.
@silvestretoribio22765 жыл бұрын
2013 BMW X3 28i is showing same message. We replace the spark plugs, ignition coils. And the engine light went off. And we thought it was fixed. But after driving the car for about 25 miles same message come on but with no engine light. Can some one help me?? Thank you!
@engineeringinvestigation62085 жыл бұрын
Please do a full scan on the car. Get the fault codes... that will be first step