Dryer Repair - Replacing the Dryer Drum Slide (GE Part# WE1M481)

[@gamingmuscles]

This video has the best repair music I’ve ever heard lol. Great video, perfectly explained, thank you!

[@billthurman7177]

Thank you Steve for your expertise in this area. After watching your video I was able to tackle this job with no problem. It took me approximately 20 minutes from start to finish and now we can dry our clothes without the horrible screeching. Thank you so much for your help.

[@talspen]

Update: Woohoo! I did it! I fixed the dryer all by myself..Thank you! My parts arrived today from PartSelect. I replaced both drum slides and drive belt..cleaned out machine/ducts, heating coils checked, felt checked, checked rear drum bearing, cleaned out the back of that plate too...Working and sounding better than ever now. :) Thanks

[@talspen]

Thank you! for these tutorials..This is my exact dryer! I am the home diy diva around here,so I followed & replacing the belt, my belt was broke and sure enough found that my dark tab slide was broke and white drum slide was worn..Ordered our replacement parts from partselect online and hopefully will have this fixed when parts get here this week! Again.I can't.Thank You enough!. I recommend partselect to all my friends/diy buddies now ;)

[@kevinmcconkey990]

Thank you so much for posting this step by step video - very helpfully!!

[@partselect]

Hi, Thanks for your question. Drum slides or glides are what provide support to the front of the dryer’s drum and a smooth surface for the drum to rotate on. They're usually made from nylon, plastic, or teflon, and depending on the make of the dryer, they'll have a cork or felt backing. Hope that helps!

[@scottjones8067]

Wonderful Sir! It took me approx 30 minutes compared to you approx 10min but it worked! Only issue I see is as you are facing the dryer the felt strip and looks like some of the plastic is worn away. I was able to replace both strips and at this time it works no squeaking! Again thank you for your video!

[@lennyjaythomas]

Thank you! Took me about 20mins to do this. Ordered the part from your website and received it in two days. By far the hardest part was putting the door back on.

[@pharflo]

Thank you for providing this video. It was much easier than reading a schematic. I followed your steps and got the parts replaced with no problems.

[@charliefarr4866]

Thank you so much ! Due to COVID19 stopping work for me, I could neither afford a service tech or any more destroyed clothes. One of my slides was severely worn and the other was completely gone. $12 in parts and it's all fixed.

[@partselect]

Hi, Bill! Thanks so much for the wonderful feedback. We're very happy we could be of help to you. Great job on the repair, and take care. Cheers.

[@oc9357]

Where is the high limit located at in this model?

[@partselect]

It's no problem at all, Konrad. Here's the part number required for your model, for the top bearing: WE14M124. Let me know if there's anything else I can do. Cheers.

[@stephenpagano2669]

Thank you so much. Never could have done this without your help. Replaced coils, skids and belt.$aved lot$ of $$$

[@dpittman70]

Everything Lenny Thomas said was my experience. Thank you for the video and instruction. The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I replaced the 2 drum slides and no more getting caught.

[@partselect]

Hi Daniel, great news! Glad we could help and that a fellow DIY-er was able to help you in your hour of need!

[@danh8540]

This video was very informative and I completed the task in under 30 minutes. I ordered the parts from the website and they were here in a few days. Thanks for the posting this video.

[@partselect]

You're welcome, Dan, and thanks for the kind words.

[@partselect]

Thanks for the feedback! :) We're happy to have helped. Good job on the repair.

[@migus37]

what's the best access to replace the heating element/igniter?

[@SubmitThis]

That was my issue plus a cracked Top Bearing. The video is a great way to drive business to your site. I wound up purchases the supplies from there.

[@trainingtreeranchllc4868]

Great video! Helped a girl fix her dryer and put it back together! Thank you!

[@julianzug]

Thank you for this video! Do you have a video on replacing the heating element in this dryer? Most videos show this being done by removing the drum but it seems to be one piece on this model. Thanks!

[@libsrcrazy9634]

Great video. I have this exact dryer. When i turn it on i get a buzzing noise and it wont spin. Any ideas? Thanks

[@partselect]

The drum slides shouldn't be worn out after two weeks. Can you tell that they're worn out, or are you just experiencing the same problems? Sorry for my confusion, it's sometimes hard to completely understand the issue without being there!

[@slipnorris5882]

I checked my GE dryer, squeaking noise, clothes getting caught off the top, how many slides would I need to buy, because I need all of them.

[@amandaq141]

Motor hums but the barrel does not turn. Took it apart and checked the drum slides (gray). Intact but worn. The felt is worn. Both drum slides and felt probably needs to be replaced. One white drum slide no longer has the hook to keep it in place. Used double sided tape to keep it intact. Unsure why the drum won't spin. Any suggestions? Thank you

[@stevenjrrice5694]

When replacing the top glides, is it recommended to replace the felt strip underneath at the same time? Also, since it is already dismantled, I might add that NOW is a great time to clean out the lint trap!

[@partselect]

Hi, while replacing the top glides I would suggest replacing the felt strips as well during your repair.

[@kenfitzpatrick4775]

great video!~ i have a GE Model GFDN120EDWW - do I need to take out the Drum to replace my Dry Sensor thermostat? thanks in advance!!

[@partselect]

Hi Konrad, Thanks a lot for your question here! Great job on the rear bearing repair. Are you able to provide the model number for your dryer? If so, I can give you the exact part number you'll require to replace your front bearing. Thanks again, cheers.

[@saguenayauto]

Hello I have the same dryer and and it make a squeek sound when tumbling. Is that the parts i have to change to get rid of that sound? Thanks

[@craignewman3238]

Thank You for your great knowledge. This made the repair simple. Dryer works great thanks again

[@joshhillmania3343]

Model number for the dryer? I cant find it anywhere

[@mikerandolph5827]

Kudos for your great videos!! I have the same model as in this video, but the tag with the model # is missing. Could you please share the model #. I am looking to restring the element and can't find the right part #. The only difference I can see between this video and my machine is the bearing on mine has 4 slots for slides. One other question.. are WE1M481 and WE1M333 the same part? Thank you!!

[@partselect]

Thanks for the kind words, Mike. Unfortunately, because this video was released quite a while ago, I'm not sure what the model number of this dryer is. As for your other question, both of those parts have been replaced by the manufacturer. WE1M333 is now WE1M504 and WE1M481 is now WE1M1067. Having said that, both parts are almost identical, with the main difference being the material and color. I would recommend replacing the bearing with the part that looks most similar to the original one on your dryer. I hope this helps with your repair!

[@stevenprice9186]

Hi Steve! We have the dryer in this video. We have clothes catching at the top. Is it probable our problem is the slide drums? Also it was squeaking the the felt? was coming out. We stuffed it back in and now it is no longer squeaking. Is that ok or could the be a fire hazard? Need your input for sure! Thanks for your help in advance!

[@partselect]

Hi Steven, thanks for watching! I doubt there is any fire hazard involved, but the drum slide does sound like it is worn from your description. This can cause clothing to be caught and damaged and also decreases the efficiency of your dryer. It is an easy repair; just follow the video! Best of luck with your repair!

[@Gothery15]

Thanks for the video! Really made everything easy to understand and saved a lot of frustrations.

[@RapIsDeadly]

My dryer just stopped before the cycle was done. I looked inside and saw that the felt was hanging out and was stuck in the drum. So I've got a 18 inches of felt partially hanging out from inside the door. Can I just put the same piece of felt back on...or do I need to replace the "slide."

[@alexnowell6627]

Anybody know how old this dryer is?

[@JudyDelValle33]

Hello I have model #GFDS140GD0WW the start switch is good and the door switch. Nothing happens when I press start (drum doesn't turn, and I can smell had inside the drum) could it be the ignighter?

[@chrismak4859]

Thanks buddy! I have a GE dcvh515gf1ww that is tearing clothes, clothes get caught on the upper inside of the drum. I am hoping this will fix my issue, as it feels like there is too much wiggle room between the drum and door allowing clothes to get caught up in there. I just ordered the OEM slides, wish me luck!!! Great video and for some reason I really like the music haha!

[@partselect]

Thanks!!

[@partselect]

Hi Konrad! What fantastic feedback. I'm so glad your second repair with this went equally as well as the first, and that we were able to help you hang onto your washer and dryer! Your comment would be pretty inspiring to first-time DIYers - if you don't mind, I'm going to share it with our Facebook fans this morning :). If you'd like to check it out, our page is Facebook [dot] com / PartSelect. Thanks again, Konrad. Cheers!

[@madmanbobtaylor9531]

I got a GE dryer model GFMN100EL0WW it starts runs and stops again . it says to clean lint . I cleaned all the lint even the sensors but it didn't make a difference . what else can I check ?

[@lorddan666]

What are the drum slides for?

[@nateLegakis]

Our dryer has model number gfdn110gloww and it's squeaking. do you know what parts we would need to fix it and how to fix it?

[@partselect]

Hi Nate. I've entered your model number into our system and can't seem to find a match. If you want to double check your model number, I can certainly help you figure out why it's squeaking, and what part(s) you'll need to fix it!

[@nateLegakis]

Sorry, the model number of our dryer is GFDN110GL0WW and I think I discovered the part number I need is WE14M124. Somehow the top of that plastic bearing was worn down and parts of the plastic were actually missing. Great video, by the way!

[@leonardochen6017]

I have model dcvh515gf0ww take so long to dry, which parts do i have to replace and what is the part number? thank you for your help

[@partselect]

The problem your having could be caused by a few different parts. I'd suggest looking at the drum seal - part number WE9M30 (see if it's torn or worn) or the blower wheel (part numberWE16M15) make sure that it is tight to the motor shaft. Start there and let us know how you make out!

[@leonardochen6017]

***** Thank you for fast respond. Still not helping, what other possibility ?

[@partselect]

Leonardo Chen Check to make sure that the dryer has good steady air flow - and check the dryer's vent to make sure that it's not clogged or partially clogged. If the vent is okay then start with testing high limit thermostat (Part Number WE4M80) and test with a multi-meter. Next, have a look at the igniter ( Part Number WE4X739) check for continuity and the flame sensor (Part Number WE4X448) check with a multi-meter. Have a look at the drum bearing slides (Part Number WE1M1067) Make sure you disconnect the power before testing those parts. Let us know how you make out!

[@kristinejensen7194]

clean your vent from the dryer discharge to the outside

[@luisvgarza]

HI IM HAVING PROBLEMS WITH GE DRYER HAVE E61 ERROR CODE IN THE DISPLAY SO PLEASE CAN YOU HELP ME TO FIND THE PROBLEM AND OF COURSE I BUY THE DAMAGE PART IN YOU STORE ,, THANKS FRIEND

[@partselect]

Hi there, I think what you might have is a problem with your main control board. The E61 code is indicative of improper voltage; seems to be something people experience after power surges or electrical difficulties following severe storms. If your wiring is at the correct voltage I'm afraid your control board might need replacing. Try heading to our Instant Repairman page and entering your model number in order to get the process of repairing your machine under way. www.partselect.com/Instant-Repairman.htm

[@ricksterling7944]

Great video although why BONGO'S?? Ugh....I can't "un-hear" it!

[@NathanThePrezPretlow]

Why my GE dryer goes off in 3 minutes ?

[@donjackson9823]

I replaced the drum slides and after two weeks they are already worn out. What else could be the problem?

[@Dave_Rearend]

i have this exact dryer in the video and it runs fine when not loaded but when i load it with clothes it makes a rattling noise after about 5 minutes. any help?

[@partselect]

Hi David! Thanks for the question! It sounds like you may have a defective idler pulley. The pulley is located on the left side behind the motor and rotates on a spring tension shaft. Hope this helps with your diagnosis!

[@joseagelviss2105]

I have model DCVH660EH0BB,enter service mode have E02 ERROR CODE in the display cause inlet control thermistor in short circuit , what is the part number? thank you for your help...

[@partselect]

The part number for the inlet control thermistor is PS1766014.

[@mmegllc]

I just did this with the same exact model dryer. It was working great before but made that squeaking sound. I pulled it apart just like in the video and replaced the Drum Slides. Something happened because when I put this all back together, the dryer drum is very hard to turn. I can run it with no clothes but as soon as you put even a tiny amount in it stops spinning altogether. Many websites say it's a motor problem but it was working literally 20 minutes before I took the face off and now that I put it back together, it's not. What happened to my dryer??

[@partselect]

Michael Majoris What is the model number on your dryer?

[@bobjimenez4464]

I was thinking that when I paid $1000 for my dryer it would have had Real Bearings to support the main weight bearing moving component. Shame on GE for being so recklessly cheap by including nothing more than nylon wear pads in the design of a fairly expensive household appliance. Excellent video though, you explained the job nearly flawlessly..forgot to re-connect the two wiring harnesses, but nobody is perfect. Especially the Design Engineers at GE....shame on them.

[@doctorfeinstone6524]

It's the exact same dryer they made from the mid and late 90's. Just in a different cabinet

[@andrewkagan1389]

My dryer (same as the one shown in this video) was having a problem with clothes getting caught and or black marks, but no squeaking. I replaced all 4 slides along with the felt. The dryer seems to be working well, but now it is squeaking. I took it apart again, and the slides and felt appear to be in the correct position. Any ideas?

[@rupmayur]

HOW I INSTALL COVER NOZZLE AND RETAINER INSIDE DRUM FOR GE 8,3 CAPACITY FRONT LOAD GAS DRYER WITH STEAM FOR GE MODEL # GFDR480GF/485GF

[@partselect]

We do not have a repair video for this, but it appears that you would have to remove the main top to access the nozzle holder that is located on the rear bulkhead. The cover appears to be attached to this part and you may wish to remove the front panel and drum for easier replacement, although it does not appear necessary.

[@darlaparker1125]

A real good easy repair video

[@alexanderlutz5132]

Outstanding video, thank you very much!

[@elizabethgarrison9496]

Thank you so much. This was very helpful :)

[@partselect]

Hi Elizabeth, thanks very much; glad to help!

[@leonardochen6017]

Thank you very much, very helpful

[@partselect]

You're welcome!

[@danielrealpozohdez410]

GREAT VIDEO

[@richnyert]

my dryer won't start

[@lenalynx]

Thank you so much for the video (it helps that this is my exact dryer lol

[@musicisitall]

or buy a miele...

[@rra022001]

why in the F*** are there no drum support rollers? To hell with this GE Adora dryer. Its no wonder GE WAS the company of choice. S*** for brains engineering.