DSG 7 Speed Mechatronic Installation (DQ200)

[@kadeemmeggett6324]

Would this unit cause my gears to not engage once fear is selected

[@TheGeeksofNature]

Excellent job

[@gabeebanks5985]

When removing the mechatronic unit does the gearbox need to be selected in neutral first ?👍

[@mariocars7720]

Good evening mechatronic removal / refitting how many hours? adaptation / calibration ... suitcase there for how much in total?

[@jean-remyjrledone1284]

very serious company ,I set again the repeared and reset mechatronic DSG7 without any pb ,pay attention to the little join when set it on the gearbox.

[@rmsyster]

Can you tell me what a 0 clutch is? Mine is broken and it costs like €9000 euro's according the mechanich. Please advise.

[@bvipul1]

What is a memory child part in mechatronics?

[@raymondbisset]

Has the top 2 selectors got 3 positions, I can only move the top left selector in 2 positions. I pulled the mechatronics unit off because the car would not move and I got a P 0841 code & a small discharge of oil out of the breather. Im not sure if I have also a G box issue?

[@Leon_Brown]

So you dont have to put the breather seal back after filling?

[@290Noname]

No

[@amatpenting3060]

Thanks for watching bro

[@matroksu]

So what about passat b8 with that transmission? change that oil and mechatronic oil? or not? and how much milage? thx.

[@linasvaici]

I have 2010 vw golf mk6 1.6tdi dsg 7 speed gearbox code MLE. Would my car work with the same gearbox removed from golf mk6 1.6tdi dsg 7speed but different gearbox code? Or I need exactly same gearbox code MLE?

[@jaystheone1]

What was the awsner to this?

[@reubenmatthew6759]

Hi, My Passat 2013 with DSG 7 speed engages when engine gearbox is cold (especially mornings) but doesn't engage when the engine/gearbox is hot. After turning off/On, gear selection happens but Car doesn't move. What could possibly be the issue? Need your support please.

[@Ecutestinglimited]

Hi. Please email our technical support team at [e-mail] with the following information. Your vehicle's make, model and year of manufacture, the symptoms of the fault including all fault codes, and the part number printed on your mechatronic unit. They will be able to advise you further. Thanks.

[@468garage6]

hi there i just followed your turtorial on the replacement .Firstly my original units valve body cracked at the accumalator housing . i then replaced it but used my original board .The car drove but it could only drive in d2 and s2 . Then i saw your video and did the correct bleeding , basically did everything you did.I then now left it in neutral and removed the unit . before installation i measured the selectors to 25mm and made sure the selector forks are neutral while the shifter was in the neutral position . I got everything fitted but i cannot start the car due to me getting a U0101 error code , which means "no communication with tcu/tcm. any help would be great . The car is stuck in park now , park light is flashing and dash says please put vehicle in park.

[@Ecutestinglimited]

Hi if you are getting no communications to the DSG mechatronic there may be issues such as poor fitting, bent pins, fuse or feed issue. If the vehicle all checks out as good you are welcome to send us your unit for testing and rebuild if required: www.ecutesting.com/common-faults/volkswagen/volkswagen-golf-audi-a3-dsg-7-gearbox-problem/

[@468garage6]

@@Ecutestinglimited the pins we bent yes, thanks for the reply

[@alltheusernameswastaken8936]

@@Ecutestinglimited Dam, you guys are awesome for assisting OP

[@mrsingh1696]

@@468garage6 whichs pins ur talking about where is fuse?

[@mrsingh1696]

i have same problem but i was on highwar when i changed from D TO S TO OVERTOOK a truck i lost whole gearbox n now pnds flashing with esp light is on errort code u0101

[@ProfitableSalvage]

When refitting and you say change forks to neutral does the car gearstick inside car need to be in neutral or park?

[@Ecutestinglimited]

Hi. Yes, the car gearstick and gearbox selector forks should all be in neutral when re-fitting. Cheers

[@JRamirez943]

⁠​⁠ I’ve got a u0101 error code. 09 Audi a3. Fuses and relays are good no crank no start. Car starts if I jump relay for starter. Power is going to the tcu plug. I unplugged it from tcu and oil came out mech unit. Tried to clean. No luck. P flashing at selector inside car. I have a mech on order but want to be sure before I fit it

[@JRamirez943]

@ecutestinglimited

[@Ecutestinglimited]

Hi. We would recommend checking the TCU has a good ground at the connector, as well as good communication lines (CAN high and low) to determine if the fault is with the mechatronic or the wiring.

[@dustyfruitypie1633]

I thought VW changed the oil to a mineral oil, on recall, but you are telling people to use an synthetic oil. Am I missing something!

[@ritcherklooster324]

is it normal when theres fluid in the tcm electric board on the mechatronic unit?

[@nitro_rc_dude8158]

No.

[@fernandonhamussua92]

When I put everything back, where should the gear lever be? N or P?

[@alltheusernameswastaken8936]

I might be wrong, but the lever is electronic and not mechanically connected and as such its position does not matter.

[@290Noname]

In Neutral

[@benaustin7850]

We are doing one and have lined everything up, we get a clunking noise and the engine almost does a back flip

[@shane.bacchus]

Do you have to do any programming of the mechatronic ?

[@Ecutestinglimited]

Hi Shane. When we retain the original programming when re-building the unit so no additional programming will be needed when re-fitting it back to the vehicle. All you will need to do is follow the re-fitting procedure, replace the oil and you will be good to go! Cheers.

[@a.h7761]

Hi there How do you pressurise the accumulator please

[@hifihighend]

Perfect🥂

[@yatyatim9321]

Thanks you for your explanation ..i'm technician Volkswagen from Malaysia can you explain the true adaption for me

[@yatyatim9321]

When mechatronic fluid need to replace n how much kilometers i need recommend customer to replace mechatronic fluid

[@Ecutestinglimited]

Hi Yat Yatim, "Volkswagen says no need to change the fluid again. But independents say it needs to be done every 4 years." good-garage-guide.honestjohn.co.uk/askhj/answer/79979/how-often-does-the-oil-in-the-dsg-gearbox-have-to-be-changed-

[@wiggumo]

Hi how much to replace this for me

[@Ecutestinglimited]

Hi. Select your car make and model on our website here: www.ecutesting.com/common-faults/volkswagen/volkswagen-golf-audi-a3-dsg-7-gearbox-problem/ for accurate prices. Thanks

[@wiggumo]

@@Ecutestinglimited thanksdo you provide the installation service as well?

[@Ecutestinglimited]

@@wiggumo Unfortunately we do not. However you can follow the steps on this video to re-install your unit if you get it repaired with us. Alternatively you will need to contact a qualified technician. Thanks

[@bobansupergenije7512]

120 eur

[@michaelkehdi9278]

Super crank enta

[@TheCoBBus]

I just paid 5000€ for the unit, fitment, testing, and oils…..

[@syedmesfer1879]

Hi I am from INDIA, I want to learn to repair Auto Transmission.

[@petar_d488]

What makes this f***ing thing rattle so much? I am in a middle of a dispute with Skoda because of this crap, its like marbles in a tin can.

[@JRamirez943]

Flywheel going bad nothing else. If dsg

[@petar_d488]

@@JRamirez943 Service says some noise is normal, they are not admitting a problem, my car is under warranty, what do I do, I could use advice.

[@juliewanyoike9609]

worn out release bearing in the gearbox

[@zeljkomilos7244]

Hi where Are YOU located do YOU service australia

[@Ecutestinglimited]

Hi. We are located in Derbyshire in the United Kingdom, however we offer a worldwide service so feel free to send your unit in either by filling out our online test form at ecutesting.com, or by giving us a call on [phone] Monday-Friday 9am-10pm (GMT). Cheers.

[@yanickgraham6661]

Hi do you guys have an email

[@Ecutestinglimited]

Hi. Yes, you can email our technical support team on [e-mail] or by phone on [phone] 👍