Easy power upgrade - Stihl MS 250 muffler mod

[@dannyhensley8306]

Long as you find em accordingly ur set. Just don't blow ur saw up running to lean with muffler flow changes. Don't forget fuel reburn from pullback either.

[@timberandtools]

Yeah it’s important to set them properly but also to be careful with who’s running it. I won’t run a saw that’s tuned a bit hot or that’s ported dull. Turns to much heat and will damage p and c if your forcing a full chain on a saw like that

[@ivanhernandez2371]

Amazing increase in power and faster..

[@timberandtools]

Yes it makes a big difference 🔥👌🏻

[@justsomecoolprayingmantisd6422]

I got that pipe from Amazon for cheap so I bought it. I had it totally different but redone it.

[@zeromark202]

Sounds great!

[@timberandtools]

Thanks 🤙🏻

[@wht240sxka]

My buddy had that exact welder and it did good on 1/4 inch or thicker but couldn’t get it to run great on thinner metal unless I hooked up the tig, which I also wasn’t a fan of since it was a scratch start. Miller and Lincoln is where its at…

[@timberandtools]

Been getting it better with the thinner stuff but yeah, you nailed it. Thicker stuff welds great! Traded a millermatic 251 from 2004 we bought new. Thought it was a good deal at the time haha

[@wht240sxka]

@@timberandtools just go get you a cheap Lincoln from Home Depot for light stuff. Makes it a little more convenient too if you have .035 or .040 wire in the snapon and .025 in the lincoln. Instead of changing spools and tips. I have a lincoln 180 and a 140 set up differently for mig and a separate tig setup with argon for my stainless and aluminum. Since big box stores sell em now, makes it a lot easier(cheaper) to do.👍🏻👍🏻

[@timberandtools]

@@wht240sxka not a bad idea!

[@justsomecoolprayingmantisd6422]

I'll video my exhaust build on mine here soon and post it.

[@timberandtools]

Absolutely 💯

[@justsomecoolprayingmantisd6422]

Getting ready to build exhaust for my 036 Pro 😎🤝🤘

[@timberandtools]

036 is a great saw 💥💥

[@justsomecoolprayingmantisd6422]

@timberandtools - thanks buddy 🤝. I am doing final preparations on it and will post video tonight hopefully. I had to clean up my welds a little bit because I believe my gas was about out on welder and looked crappy. I’m ocd on my welding, but as long as it’s burnt in and holds is all that matters right lol. Ill let you know when I post it

[@timberandtools]

@justsomecoolprayingmantisd6422 sounds good!!👌🏻

[@justsomecoolprayingmantisd6422]

I fabricated me an exhaust for it 🤝. I will post video if you want to check it out sometime

[@timberandtools]

@@justsomecoolprayingmantisd6422 Post her up!

[@justsomecoolprayingmantisd6422]

@Timberandtools - hey buddy I finally posted a video even though I didn’t get it finished or it’s not running, but just wanted to share and show ya. I’ll be giving you a shout out in my description 👍🤝🇺🇸

[@timberandtools]

@@justsomecoolprayingmantisd6422 nice!! I’ll check her out now 👌🏻💥

[@timberandtools]

@@justsomecoolprayingmantisd6422 just subbed

[@justsomecoolprayingmantisd6422]

@@timberandtools subscribing you as well friend 🤝🇺🇸. Sorry I didn’t even think about it before or I’d done that sooner

[@timberandtools]

@@justsomecoolprayingmantisd6422 thanks!

[@bdixon2668]

The easy way to mod the 250 is grab an AUS muffler from your dealer for $25..it’s already what you’d make..have done it to a few..

[@timberandtools]

Aus as in Australian? What’s the muffler like?

[@bdixon2668]

Correct, available at your local dealer…the front “hole” is the full square. Then do the screwdriver tweaks to the cover plate and you’re done. On one of mine, I used a punch to reach in and make the baffle holes, angled towards the exit, much like the cover plate louver trick. Makes it super simple. 👍

[@oscaresquivel9822]

Can’t hear with the music you got man

[@timberandtools]

Shoot !! Thanks for letting me know for some reason this happened on another video I have it set low when I edited it but people commented about one other video being the same way

[@garyleppla9314]

Dirt Bike Chainsaw !!!

[@timberandtools]

@@garyleppla9314 hahah brappppppppp

[@frios011]

That’s a hell of a lot of work for NOTHING!

[@timberandtools]

It really is not a lot of work and also very noticeable gain in power