ECU MASTERS PLUG N PLAY KIT (TURBO IS300)! Finally a TRUE Plug and Play Kit? Step by Step Guide!

[@motaxhinothgodson2405]

Ha that’s funny I’ve been looking for plug and play kit for my 01 for 4 years and now that I’m doing an ls swap I stumble upon this 😭🤦🏽‍♂️

[@Barely2JZ]

Curious as to why LS rather than NA-T?

[@lomon3877]

@@Barely2JZI regret not ls swapping now that I’m knee deep into na-t, it would’ve been way cheaper and arguably cooler to ls swap

[@trivium2590]

Please do a follow up video on this car/ecu combo!

[@youngbullsgarage7322]

You just saved me so much of a hassle man thank you I’ll be posting the build soon when I get back home

[@TrackstarMediaworks]

Thank you so much for the support

[@thejspencer6176]

Ordered mines a few days ago and finally glad some decided to make a video

[@ultrablue2]

Did you ever do a follow up video with the automatic IS? I’d like to see dyno numbers and tu ability. Any drawbacks?

[@dan91sgarage]

Me too, the ecumaster setup looks great. Would love to build an is300 / gs300 + turbo, my only concern is how much power a stock auto transmission can take?

[@skippypeanutbutter9136]

@@dan91sgarage the platform is old enough to drink. This has been covered extensively in at least 2 forums. Auto trans can take the most abuse of any stock offering (manual or automatic). The main thing is you have to shim the auto trans to hold the higher power. I think you're good to ~400 WHP, or more, reliably

[@thegillfamily8704]

thank you for this video and the step by step for ecumaster install... question, or in your opinion... the ECUmaster pnp adapter for the 2jzgte vvti should be quite similar in installation, and pinout, yes? I have a JDM 1996 Supra with a 2jzGTE VVTI engine. thank you again.

[@jameswood9709]

Ethan is THE MAN!!!!!!!!

[@BillerProductions]

Thanks for the video planning to purchase one for my build!

[@ESherbinFox]

Applaud you for going through this....

[@TrackstarMediaworks]

👍👍👍

[@Mrsark5919]

Great info , top notch knowledge .. Keep up the good work

[@TrackstarMediaworks]

Thanks for the support 🙏

[@Kawichris636]

Got the same setup on gs Can’t wait to take my car to you get it dialed!

[@TylerF30]

What did you do with the b1s1 b1s2 02 sensors just disconnect them??

[@Kawichris636]

@@TylerF30 only need 1 wideband sensor in your down pipe to read afr’s no other sensors are needed anymore being standalone

[@okistash3075]

@@Kawichris636 hmmmmmm

[@911engineguy]

Great video... Looking forward to trying one of these.

[@TrackstarMediaworks]

Thanks for the support!

[@danthomas86]

Been waiting for a video on this!! 😁

[@TrackstarMediaworks]

Awesome thanks for the support!!

[@danthomas86]

@@TrackstarMediaworks own a is300 in the UK, manual swapped and turbo and so will be watching the progress ✌️

[@jvh22a]

Great info! Thanks

[@TrackstarMediaworks]

Thanks for the support!

[@jyudat4433]

this is crazy. where do guys like you learn all this stuff? aside from yt vids and forum posts is there literature and books and courses and what not?

[@AtomicFirecracker116]

I need a part two

[@lokiiddqd]

would love one but guess ill have to check if the wiring is still similar to rhd is300s

[@CrazySquirrel98]

Will it work for auto n manual transmission

[@brotherdarknessgaming4479]

Man i need the one for my gs300 2jzgte so bad, im boost cutting so hard

[@radiodunja]

the yellow cables from the adapter (adapter to ecu) are included in the kit

[@RamRam-wb9nw]

Haltech makes one for is300 but not gs300 but seeing this video I'm subscribed to him and I'll buy this instead

[@larrycorpuz2644]

Do you make standalone harness using factory harness ecu for Is300? I planning to the 2Jz on the boat

[@johnnyjeffers4764]

Been trying to find a video on this set up for a while, great stuff brother, are you planning on putting the ecu on the inside and tucking the wires?

[@TrackstarMediaworks]

We did a slick engine mount on this setup! Going inside is definitely a great option as well!

[@johnnyjeffers4764]

@@TrackstarMediaworks I have a 2004 Lexus IS300 sport cross and In the process of putting on the turbo. But just been on the fence about the harness. You guy got an IG?

[@tezzaking1014]

Hi very interesting video I have a Toyota altezza sxe10 with a 1jzgte vvti jzx110 I am wondering if the Ecu Master will control the engine fully and is just the engine transmission alone is not controlling

[@reececarpenter7426]

Do you know if you can raise the rev limiter, even with e-shift? Or will the trans still shift at 6800rpm?

[@isaiahsainz1040]

You are doing gods work sir, thank you for this video

[@geraldstorch6400]

I just installed my EMU black set up or actually my tuner is and I got my car back from him this weekend for some reason starting or like a hot start. I will have to give it a little bit of gas and cranking it and he is telling me normal because of the drive by flyers is there anyway possible I can make adjustments to where I just keptthe car without gas

[@spagez]

Great video. Since the stock IS300 ECU is retained, will I pass an OBD2 Emission test with this setup?

[@TrackstarMediaworks]

As long as the tune is set up correctly and the modifications ! Yes you should be able too!

[@fazfici6449]

Where did you put the emu black. Same location in the engine bay or were you able to relocate it inside? I feel like it won’t reach so I figured I’d ask before I continue with location.

[@rocketpoweracademy6658]

How do you run your cam and crank sensors? the grounds are factory spliced together, how do you read resistance?

[@mrjerrylee]

does the 2JZ-GTE plug n play kit also can use on 2jz-ge ecu?

[@2SSteppin]

My emu state says inactive and when I go to output assignments they Al say not assigned ?

[@2SSteppin]

Never mind I’m an absolute goofball and didn’t load the base map

[@b.s.mboostedsuspectmotors5441]

Do you have to calibrate the throttle body or does stock ecu controlling it

[@ScottDambrose]

Is this PNP for a 03 GS300 GE VVTI A340? I have an AEM V2 that no one wants to wire/ touch in Florida.. harness is discontinued..easier to swap ECUs and find a speed shop.?? Been bouncing around shops.. Titan, Induction, and they will not touch the wiring. They just want to sell me parts…

[@masteroogway6199]

with this ecu, in e-shift can you select gear 1-5 and the auto transmission not change the gear?

[@tripphopper3374]

Were you able to come up with a method to keep the stock ecu in its factory location and be able to put some kind of cover on it that would fit over the yellow plug n play harness wires?

[@ManicsVideos]

You can tuck everything into the factory box just gotta cut a small whorl for the harness to come out of

[@CJ-uu3lk]

Can I turn off my check engine codes and light with this plug and play? I need to get my car inspected and in Florida any check engine code won’t pass and I want to install this unit? Any ideas???

[@GREMDAMENANCE]

So you have to buy these separately ?

[@kevinc9934]

could you use this same ecu to also delete the DBW?

[@jasoncruz2142]

Can you tune my car with a dyno in Florida ??

[@TPMach1]

Hey do you have one for a 2001 IS?

[@gbriggsy5958]

what would you recommend for a 1998 lexus gs300 2jz gte vvti

[@roberttuckerjr4718]

With this black ecu master ecu will you still be able to pass emissions test that plugs into the 0bd2 connector?

[@drainis]

Wow, I'm definitely getting this for my IS build. Is that a stock motor, like the pistons/rods? How much boost are you guys running?

[@TrackstarMediaworks]

Stock motor and trans running 10lbs

[@drainis]

@@TrackstarMediaworks Awesome. Are you running on E85 or premium? Thanks for the reply.

[@920.streetstyle]

@@drainis these cars use 91 or higher from factory

[@drainis]

@@920.streetstyle I know, but when some people keep the stock compression, they'll convert to E85 to avoid blowing the engine with more boost

[@overbuiltautomotive1299]

@@920.streetstyle they do not like 87 as me how i know lol

[@justinmagana9630]

Is this turbo motor running the non return style fuel system or is it using a return system. Does this ecm allow to run individual coil on plug as well ?

[@marioandultrachap]

Hey so im a little confused are you able to control the drive by wire on this because when i go to look the product page it says this: "The ETSC-i throttle body must remain connected to the stock ECU to correctly control the automatic transmission. For this reason, the EMU will not have control of the ETSC-i TB." Im not sure what that means can the stanealone still control drive by wire or is that something completely different?

[@rogermurillo5608]

Does this work with the 2jz gte sawp in the is 300? Ok thank you

[@matthewamaro5834]

Will the plug and play kit work on a total engine swap? I’m putting the 2jzna-t into a 300zx, I have the stock ECU but 2 connectors are cut ( i think they are from the body harness)

[@Darkvoidproductions1]

I would also like to know as i'm doing the exact swap on my 91 z32 xD

[@MHPDRIFTING]

it makes more sense if you want all gauges and stuff working in the original car 🙂

[@aestheticgarage]

I have an 2001 Lexus is300, would I still be able to do this in a 2001?

[@negritoz32]

Can i ask question what kinda laptop can i use to tune. That laptop support that softwarewear. Thanks in advance

[@danthomas86]

Any follow up vidoe on this.. How she do on the dyno?

[@TrackstarMediaworks]

It did very well on the Dyno! Unfortunately we had a busy day at the shop that day and were not able to capture it on the Dyno!

[@brendanedwards1416]

I noticed in the last clip of this video where you did a pull, I heard a slight hiccup, did you find out what that was? I have something similar going on

[@brendanedwards1416]

Like around 4K rpm’s (estimating) it seemed there was a slight hesitation

[@ThatAznRice]

Is your build a na-t on a unopened engine? If not what do you have done to the engine?

[@tahasultan7409]

Were is your shop located???

[@chrisej207]

Are most stand-alone ECUs programmed to run on windows instead of Mac?

[@lucygoose23]

Is there a part 2?

[@eriklopez4720]

Can u have ac woth that ecu?

[@PH020]

i wonder if this is similiar information for the 2GS300, theres not much support for the GS's even though there pretty much the same car... does the emu black compatible with the GS300's?

[@TrackstarMediaworks]

I would contact ecu master USA to make sure it’s supported!

[@king_sin2533]

Did you use a turbo kit? if yes can you send me the link please?

[@negritoz32]

Where do you install you iat sensor

[@damnitdang]

Do ecu master leave pigtails in the pnp harness for gauges? Clt,afr, psi? So we don't have to tap into a wire to use for out gauges

[@TrackstarMediaworks]

Yes it does !

[@Nyaght]

I mean would it work for my 98 gs300?

[@drainis]

Hey, are you guys running e85 on that thing? Thanks for the content.

[@TrackstarMediaworks]

On this car I believe we were on pump gas 93

[@negritoz32]

Is possible to you to send me or paste actual firmware and base tune for the is300

[@b.s.mboostedsuspectmotors5441]

How much power are you making on 10s Psi

[@ManicsVideos]

Do you have any imagines of how you mounted the ECU?

[@AlexanderJuholaJones]

Thinking about getting this for my 2003 GS300. I'm in France, to pass an inspection here none of the dash lights can be on. So no check engine and no traction control lights, ABS etc. OBD2 port must also work. Does this harness and ECU cause any check lights or codes on the factory ECU?

[@TrackstarMediaworks]

If set up correctly it will not throw any codes or lights

[@shaunkeefe4279]

Will this work for a manual 04 is300 I'm getting ready to boost it and I need some guidance

[@TrackstarMediaworks]

Yes it would depending on your set up but we all always recommend checking the ECU Masters USA website for compatibility

[@chriscole2020]

i need something just like this for my SC300. im still on auto. will this work with the SC?

[@Pelllaw26]

Believe this kit is more towards the vvti engines. The plug and play worn work but the ecu will. They do have a pnp kit for the sc300 but it's for the ecumaster emu and not the black series. U honestly probably don't need to buy the black one if you can run the emu.

[@shagmike8672]

Still liking the setup?

[@TroyCityMedia]

Do you enter in the injector size? Saw you test them but didn't hear anything about selection

[@TroyCityMedia]

Nevermind lol i must have missed it getting a drink just replayed it

[@cailiyahphillips]

Will this work for a non turbo stsup

[@motoringinc2568]

What boost controller was used?

[@mr_iggan]

Where did you mount the Intake Air Temp sensor?

[@2SSteppin]

I welded the bung onto I’m the intake pipe

[@offlinemve5054]

Is there a way to make this work with a 01 is300? I know they have slightly different ecu’s

[@TrackstarMediaworks]

Check the ecumasterusa website to check and see compatibility! 😎

[@frankiewalnuts]

can this handle 700hp single turbo 2jz?

[@shadowbuilt915]

I know it’s an older video , but you mentioned it’s your favorite ems. Is this still the case ? I’m really considering this for k swapped Honda vehicles.

[@TrackstarMediaworks]

Yes highly recommend ECU Masters for this!

[@shadowbuilt915]

@@TrackstarMediaworks thank you for the input ! Any videos of any of them coming up ? Also considering this for B series vehicles.

[@asian380]

is this on a stock exhaust? If so what components was used to mount with the headers to fit ?

[@2SSteppin]

This is turbo so no not stock exhaust

[@caribbeankartel5758]

What’s the platform you use for the tuning??

[@TrackstarMediaworks]

Depends on the vehicle . On this one ecu masters

[@prussnblk6457]

Just the harness is over $800

[@jasonjordan1053]

Is this better for auto? wound you recommend for 5speed?

[@TrackstarMediaworks]

I would recommend the 5 speed if you have the option.

[@mikesmods]

does all the gauges and cruise control still work?

[@TrackstarMediaworks]

Yes !

[@shagmike8672]

Would you still recommend this ecu for the IS looks easy? Thanks in advance

[@TrackstarMediaworks]

Very much so!!!

[@shagmike8672]

Awesome, just got a boosted one and ive been looking at ecu this one seemed to be the best option

[@TrackstarMediaworks]

Definitely is the best option for you!

[@migueltovar9702]

What turbo kit is that?

[@williammcgrory5795]

do you have a kit for the gs300 ?

[@TrackstarMediaworks]

Ecu masters USA does and we can install !

[@OnlyImBad]

What turbo you got

[@eze8024]

This let's you keep the stock ecu so you can keep the auto trans working as it should? :O Does the obd2 port still function for diagnostics and 0bd2 plug in state inspections?

[@trilliamogdlocog4986]

Have you found out if the obd2 works with it?

[@eze8024]

@@trilliamogdlocog4986 no clue. Not trying to be the guinea pig

[@trilliamogdlocog4986]

@@eze8024 I'll let you know here in a bit I have a gs300 I'm tinkering with

[@804MRMAN]

​@@trilliamogdlocog4986Sooooo what was the outcome

[@trilliamogdlocog4986]

@@804MRMAN Traded my GS before I finished the project, but really unless your running high hp I'd just go piggy back. Ecu black is pretty expensive for what you get but thats just my opinion now.

[@altezza2jzking886]

Are you having issues tuning the is300. I have a buddy with this same set up but on his gs400 with a 2jzgte vvti swap and his issue is the throttle body is wanting to close at wot. I’m my self have this same set up for my is300 2jzgte swap vvti I haven’t installed it yet due to him having the issue. Maybe you can shed some light on where to start.

[@wannabecarguy]

Just yesterday My car started doing that. Factory ecu. Gonna inspect the encoder. Soldier joints.

[@TrackstarMediaworks]

Fortunately we did not have an issue with the throttle body wanting to shut at wot

[@wannabecarguy]

@@TrackstarMediaworks on another IS300 the lead free soldier joints cracked. I quick repair was all it took. On the accelerator position sensor.

[@wannabecarguy]

kzbin.info/www/bejne/gmjYo4iMe91nesk

[@attzelonvenus]

i have a question do i buy the is300 adapter or the 1jz adapter because im going to engine swap my is300 with a 1jz vvti ?

[@TrackstarMediaworks]

Great question when it’s comes to getting the correct hardware we always recommend contacting ecu masters USA for compatibility questions!

[@andrewmaulkin5064]

@Trackstar Mediaworks how go I go about getting one of these harness as iam doing a 2jz ge swap in my is200

[@TrackstarMediaworks]

Check out the ecu masters USA website and order it!

[@andrewmaulkin5064]

@@TrackstarMediaworks thanks for your help 👍

[@PhazerMike]

First🙂

[@TrackstarMediaworks]

Awesome bro 💪

[@KickRocks873]

Another "plug and play" kit that makes it impossible to put the cover back on the factory computer box.

[@timothywilkinson6177]

What turbo manifold is this?

[@TrackstarMediaworks]

Sorry! Don’t remember what turbo manifold brand it was! Lots and lots of cars lol

[@overbuiltautomotive1299]

did you all add any ring gap

[@TrackstarMediaworks]

Wasn’t something we dealt with on this build !! Thanks for support!

[@overbuiltautomotive1299]

@@TrackstarMediaworks understood thanks and be blessed

[@AIR.FUEL.]

Does it throw any lights in the cluster!?

[@Kawichris636]

No

[@AIR.FUEL.]

@@Kawichris636 thanks

[@xjv5835]

How much horsepower is this ecu rated for ?

[@TrackstarMediaworks]

ECUs don’t have a horsepower limit necessarily. Your engine build will be your restriction. Not ECU

[@xjv5835]

@@TrackstarMediaworks thank you brotha I appreciate it , I was gunna run the Ecu master black with the pnp harness for my NA-T built stock auto

[@natel-adventures]

does it work with the 2jz-gte swap?

[@TrackstarMediaworks]

Hey we always recommend checking the ECU master USA website for exact compatibility!