Arduino Hydroponics, DIY Hydroponics System using pH Sensor & EC Sensor, Hydroponic

[@РэйЧехов]

Man, this explains a lot. I making marks while watching it. And already remade half of my scheme. Thank you

[@chimpofm]

Totally amazing video. Finally i can read ph and ec at the same time. This is perfect for any recirculating hydroponic system. We would love an IOT blynk version of this using a esp32.

[@sp3cialck]

Yep, i'd like to have the same system using a esp32 to run with home assistant!

[@ralphbooger4756]

what range of ec is it reading? specs on tdm meter says it only has range 1000ppm, my ec calibration fluid is 1800ppm, is it enough for hydro?

[@chimpofm]

@@ralphbooger4756 ppm and tds are conversions of ec. Ec basically reads resistance...

[@ralphbooger4756]

@@chimpofm so if the ppm range is 0-1000 ppm, that would mean the max ec value this board can read is under 2.0 ec? which would be on the low side for hydro? im a little bit confused about the ppm to ec conversion, ive seen 3 different ways to convert it, on one scale was 1000ppm = 1.9-2.0 ec, another scale showed 1000ppm as 1.5-1.6 ec. im trying to figure out if i can use this board, in my setup i would need to accurately read the ec at 2.2... and even a little bit higher to make sure it is not too high... so around 2.4-2.5 atleast. could it be adjusted to read like 500-1500ppm or am i misunderstanding this completely? sry bout the big post but im confused lol

[@chimpofm]

@@ralphbooger4756 ive never exceeded an ec of 1.5 and those were trees... i only work in ec so i dont worry about conversions . 0.35 babys. The 0.56 after 3rd set of leaves. Then you can calculate ec required by checking consumption.

[@quirijn3865]

It was so easy to understand thanks to the slow yet articulate speech and with vey detailed information about the project!

[@j1-31g.laxmiprasanna8]

Mini Project ah?

[@nickstaresinic9933]

Very informative, thorough, and particularly well presented. (And the "soldering tango" music was a nice touch, too.) Thanks!

[@sudheernagala4642]

Bro meru konara.

[@sudheernagala4642]

Maku echi brooooooo😊

[@nousagi7437]

How about using stepping motors to dip and retract each sensor? dip the sensor for a period of time like 5 to 10 seconds, make an average of all readings done in this time, store it, proceed to the next sensor, do the same task for all of them, and display the information after the probing process is finished. Of course this should be done in still water, like a tank connected in series to the pipes system.

[@nachnamevorhanden3335]

stepper motors can not swim.

[@samsteel4456]

@@nachnamevorhanden3335 smooth brained fella arncha?

[@TheKash19786]

Very Informative and interesting

[@babalolasulaimon-h8q]

I'm working on a water quality monitoring project using ESP32 WROOM, pH4502C, and EC Board v1.1. I'm facing challenges with connection and coding the components, especially during the pH offsetting, which isn't producing the expected results. I'd really appreciate your help in resolving these issues. Your expertise could make a big difference in achieving the project's goals. Looking forward to your guidance! Thanks!

[@lucasamiri4794]

So, very helpful. Thanks a lot

[@ahmedmabrouk9891]

best channel

[@kebunkita4260]

Very helfull video thank you very much

[@s4chin_verma]

Very useful and Informative video Thank you ❤

[@express375]

Is there a facility were this could be made to order, with credibilty that it would work, thanks really clear instructions.

[@Venkata_CV]

Very nicely explained. Thank you!

[@LiFeeIsSMusicC]

i have not understood what is that IC1 you put in the final board between the two capacitors ... Thanks for the amzing video!!

[@chemeng-industrialacademy]

Can we check ph of harsh chemicals like concentrated sulphuric acid and potassium hydroxide without damaging it, and what about its accuracy, and reliability?

[@khurramshahzad2899]

Great brother

[@olaoluwaraji2335]

Nice video. Would the setup work if its only the Vcc pin of the TDS you switch on/off instead of switching both Vcc and ground. Thank you

[@mr.anonymous298]

Very well explained tutorial! Thanks a lot, sir!

[@ElectroniClinic]

Glad you liked it

[@egoistzxc]

Can you use NPK in direct water?

[@KomplikevychOstap]

Hey, thank you very much. Just wanted to check if using NPN and PNP will solve this problem, and here you are, you gave a result. So, also if you are better in electronics, what about using mosfets like N and P type will it also work? Because, I suppling sensors from separeted source and it has a huge current strength, so think I can burn bipolars.

[@KomplikevychOstap]

So, maybe i will clarify, you used 2 pins of arduino but i want to use only one, so i want to connect NPN to arduino pin, and PNP base to NPN collector, so then when NPN will be open PNP will also open. But that way we need to deal with high current.

[@prestonashworthmusic]

This is great work, thank you!

[@aminhassan9648]

Excellent , I learn a lot from this video. my problem is in the code. how to combine them together

[@nuroo1]

Awesome. Thank you Sir

[@PhanTiDu]

I really wish there was an step by step video for people without any pre knownledge:(

[@mark3dprinters150]

Great work now we are expect the same results with esp32

[@ElectroniClinic]

next i will make the same using esp32

[@isfandriyasintasari6335]

Let me ask, can this system (using 2N3906 PNP transistor type and 2N2222 NPN transistor type) work if using ESP32? please answer

[@gazorbpazorbian]

How often does the sensor ph sensor has to be calibrated ? Can you leave it in the water for extended peroids of time?

[@khurramshahzad2899]

Thank you

[@naveenvaid4318]

great job sir but i want to auto calibration pH meter code if you can plse

[@simunhprak2296]

hi sir do the libraries are install from arduino library or i need to download from your library?

[@afiffarhati4580]

what is the role of the ph sensor module (or shield), the little card that links the probe to the arduino card? I do not have this module and I cannot obtain it, How could I replace it and make everything work?

[@rafalc.4352]

How long you can keep ph sensor in a solution? Is it reliable? Thanks

[@digimxorg2516]

Sir I am using diy ec meter in this circuit which has ec1 ec0 and VCC and GND what will be the circuit for breadboard it have 4 pin

[@LinoTech]

ciao, sto riscontrando questo errore durante la compilazione dello sketc Compilation error: ‘fdevopen’ was not declared in this scope Mi puoi aiutare?

[@bmlim6238]

12v 입력이변 7805가 필요없이 바로 vin에 접속해도 되었을텐데.... 5v가 필요하면 5v출력단에서 얻으면 될테고..

[@rendycahya457]

SIr i hv question for Turbidity sensor in your website, why when I turn the bolt knob on the A&D module nothing happens and it doesn't change to 4,2 or 4,1

[@mikael4716]

Do you experience that the PH sensor over time gives incorrect values? Does it need re-calibration or cleaning since it is submerged in water constantly? Thanks for inspiration

[@ElectroniClinic]

ya, it needs to be recalibrated. But the expensive ones needs recalibration after months.

[@99klicks59]

I have a Problem i can enter the PH calibration MODE with “ENTERPH” but not able to “CALPH” when I enter this word in CMD Serial monitor nothing happens.

[@danyamohammad6437]

great

[@siddhant.jaywant]

Hello Thanks For the Video! Can I get the circuit diagram of pcb i.e. Arduino Development Board use.

[@adeharrisibiza]

a couple of q´s - can i use an esp32 instead of the uno? do i need to do 12v conversion - and not simply power from 5v ? thanks

[@ElectroniClinic]

you will get all answers, next week i will use esp32.

[@simunhprak2296]

hi sir i got this problem (Compilation error: no matching function for call to 'SimpleTimer::setInterval(long int, void (&)())') it is not working what should i do?

[@Fachripm_Fai]

Sir how if i use esp 32 to connected the transistors?

[@electronic7979]

👏👏👏

[@hamadalkuwari2754]

Do the temperature , ec and ph sensors effect each other when in the same tank?

[@ok-mj3nh]

hi sir, may i know which software u use to draw the schematic diagram at min 13:13 ?

[@lauren9457]

Is this hardware compatible with pic microcontroller?

[@vincenzogammella3158]

hello there is someone how have the project ready to sell I'm very interested to buy some tanks for future answer and very beautiful video congratulations

[@juwonggaming7070]

hey brother why my temp output is -127C, my EC is -0.3 and pH is 20+? can you help me with this?

[@somupanditvines9908]

Sir I want to control it by my phone & P.C what can I do for it 🙏 Please Tell Me Sir

[@ElectroniClinic]

you can use Arduino IoT Cloud, this way you can use your computer and you can also use a cell phone application for monitoring and control. Watch my video on Arduino IoT cloud.

[@mewtshorts8257]

can i read sesnor values 24/7

[@naeemhaq3504]

Assalam o Alakum. whats your qualification? good videos

[@srevinUreuqnoC]

Jai Shri Ram bhai, I think he is a "Genius" :D

[@martinkaspar5095]

Dude - well done: good day - great vid - awesome. How to draw a sketch diagram - here!? - i need a sketch diagram for wiring; i want to do some work with sensing ph in Coffee and water - Can you help here out!=? Look forward to hear from you

[@ElectroniClinic]

circuit diagram is available on website. check link in the description.

[@jayprajapati-ge9ds]

how to install libraries for code and use it

[@krakeshpatra4686]

Hi Sir I this device with full working model

[@amitbakshi5083]

Where can we get the components for commercial Hydroponics project applications

[@jameslockhart1028]

How can I contact you, in hopes I could commission you to help me finish the code in order to run a peristaltic pump for ph down

[@jairosadiwa3536]

Can anyone tell how to achieve a higher reading ppm since the TDS sensor can only read up to 1000ppm??? Thank you

[@bestankit88]

Awesome, what was the total hardware cost of the project?

[@erlandrewabrasaldo3320]

may i know the unit of the EC?

[@j.mithranjegathesan7449]

can i use the program for arduino uno?

[@ElectroniClinic]

yes, arduino.uno and nano are same.

[@nicholasleehing1897]

Where can i find the code?

[@jairosadiwa3536]

Hello I just want to ask what is the purpose of temp. Sensor? Thank you

[@QuantumNachos]

good for hydroponics

[@DeniskaNYC]

Great project. Thank you for sharing. Any plans to do something similar on NodeMCU base and Blynk? Would be great to get data on your phone. Thank you again.

[@ElectroniClinic]

yes, i will be doing the same project using ESP32.

[@chimpofm]

@@ElectroniClinic comming soon ?

[@CNCwt]

@@ElectroniClinic Yes, would love to see this same thing implemented using the ESP32.

[@bestankit88]

Looking forward for the video using ESP32 sir

[@mayankverma8318]

Hii brother. Can you please make a automatic water level indicator just like kiyani tech made. Kiyani tech used only ic instead of complete arduino board so circuit became quite difficult. Brother i request you to please make such project by using complete arduino board (instead of only atmega chip).

[@fernandomaldonado599]

Link caido 😣

[@khurramshahzad2899]

Sir please connection in diagram and program install code

[@ElectroniClinic]

these are available on website. check link in the description.

[@khurramshahzad2899]

@@ElectroniClinic ok

[@khurramshahzad2899]

Thank you gret job for Pakistan

[@amirulmateen8483]

hello brother, need the code from your website🥺

[@ElectroniClinic]

It's available on electroniclinic.com

[@j.mithranjegathesan7449]

sir can u do this video again but by using arduino uno R3 PLEASE

[@ElectroniClinic]

Arduino nano and Arduino uno are the same. You can use Arduino uno without even changing a single line of code.

[@j.mithranjegathesan7449]

@@ElectroniClinic sir is the way of connecting the components same

[@ElectroniClinic]

@@j.mithranjegathesan7449 ya same

[@j.mithranjegathesan7449]

@@ElectroniClinic thank u very much sir for clarifying my questions. Is there any chance i can contact u personally sir because i have some doubts about my project

[@ElectroniClinic]

@@j.mithranjegathesan7449 you can contact via Instagram

[@dcompanyproduction3421]

Hi bro I saw the ur project we are doing same. Can I buy this project with all connections done and i want it before June 2

[@muhammadfawzy4967]

bang nakk

[@afiffarhati4580]

what is the role of the ph sensor module (or shield), the little card that links the probe to the arduino card? I do not have this module and I cannot obtain it, How could I replace it and make everything work?