Absolutely great work guys can't wait to see more videos little trick with the Saito crab is that it can be turned around
@thomasm.hindiii66052 жыл бұрын
Hi Rob, nice to see that you are back at it....
@charleshart69922 жыл бұрын
Great progress!
@ScrapYardDog642 жыл бұрын
Hilariously funny but informative, excellent video work, best RC channel bar none!
@pdtech45242 жыл бұрын
Like factory but better! ⚠️👍😁
@markgurney87252 жыл бұрын
Thank you for doing this. I have the kit and have more confidence building this model
@Vass8812342 жыл бұрын
Excellent!
@MarkCroucherRC4fun2 жыл бұрын
Thoughtful installation those far thanks for sharing. I built the VQ Tiger moth nice build.
@Rcmodelgeeks2 жыл бұрын
Cheers Mark
@alvinrcflyer97472 жыл бұрын
Another great video guys, thanks for sharing, I’m sure you already know this but just in case , on all of the saito single cylinders, you can reverse the carburettor which would lower the throttle arm more inline with the original servo position on the model, and also you would then have the high speed needle exiting out of the top of the cowl, rather than the bottom, you would obviously still have a similar issue accessing the low speed needle tho, Thanks again guys , all the best Alvin
@ronwebb32422 жыл бұрын
Fantastic and coming along nicely. Can’t wait to the next episode covering the servo install ‘down to screw level’.
@lukelane54632 жыл бұрын
I'm sure you can rotate the carburetor 180 degrees so the needle valve is at the top and throttle arm at the bottom. I done this on my 125a when installing it in a Christan Eagle.
@alfiecartwright96552 жыл бұрын
Great video guys, looks like you’ve done a great job on the kit and can’t wait for the next video
@andrewpotter12062 жыл бұрын
G'day I love the detail of the panel and glad they included the yokes,looks like a really nice kit.Hope the heat isn't too bad for you.Good news my new residents has a garage and a workbench,so I'll be building a 1/7 scale Tiger Moth (crop duster version) ,that Dad flew when he was with Aerial Agriculture,VH-PCB ,and is now on display in Walcha Pioneer museum NSW,..Cheers lads,stay cool!
@Rcmodelgeeks2 жыл бұрын
Awesome!. i look forward to seeing the progress..
@vulturedroid98042 жыл бұрын
With that much steering throw you could tether race it with the wing off. Good for engind run in at normal flight speeds.
@pcplayermalc2 жыл бұрын
Awesome video..again. I love the banter. Could you make the yokes move with the correct surfaces?
@Rcmodelgeeks2 жыл бұрын
Strangely enought i did think about that...
@pcplayermalc2 жыл бұрын
@@Rcmodelgeeks It would make it better than factory!
@MrCdix2 жыл бұрын
Did you remember to drill a hole in the firewall for the steerable nose wheel. Great video from mad Colin and captain Rob 👍👍👍
@Rcmodelgeeks2 жыл бұрын
The tube for the steerable nose leg push rod was factory installed!
@MarkCroucherRC4fun2 жыл бұрын
@@Rcmodelgeeks but better
@RCJunky2 жыл бұрын
Could just rotate the niddle vale so it comes out the top or fit a remote needle valve kit.
@ColinJamesPoulter2 жыл бұрын
All I can say is "just like factory but better"
@darkofc2 жыл бұрын
👍👍
@chksix2 жыл бұрын
Damn, I wanted to see you put the screws in the servos.
@Rcmodelgeeks2 жыл бұрын
You can have that pleasurre in the next video hopefully ;o)
@russcole56852 жыл бұрын
Late to the video,. It's a shame there was no room to fully invert the engine, makes for lateral balancing easier and give access to all needle valves. Sort of a poor idea having the front leg mounting block so large