I should have been a carpenter (a hammer, speed square and a hand saw) or an electrician (a couple screw drivers and a pair of pliers) I think of that every time I’m trying to remember which blow molded case, in which drawer of which toolbox holds the special tool I need for this 2 minute job!
@jamessikes53695 жыл бұрын
"Cause i work in a lot of stuff deep in holes.....dont!" I watched that like 5 time lmao! Love you!
@Ram2253spd5 жыл бұрын
James Sikes LOL
@flatratemaster5 жыл бұрын
😉🤣🤣🤣
@billbeckett10215 жыл бұрын
The best part about being an independent tech is you get to buy ALL the tools. Now I see why you need to edit your vids!
@charliemagoo79435 жыл бұрын
Back when i started you could use an open end adjustable wrench to change spark plugs. But back then you changed the plugs on a monthly basis or 500 miles whichever comes first
@pjg33115 жыл бұрын
I bought that 9/16 with the extension for the shitbox 5.4 3V engines I occasionally work on, I like the built in extension because if you go off center with the ratchet it doesn't transfer the sideways force to the spark plug. I work in municipal fleet and a lot of the small Honda GX engines on our generators and air compressors etc. have 13/16 plugs. I have a few of the GW 5/8 with different length extensions and the one 9/16, and a general set of Powerbuilt rubber insert sockets for most regular things.
@codysautodiagnosticsprogra87065 жыл бұрын
I remember my first time trying to get 14mm plugs out of a bmw that has the offset🤦♂️ got the same Matco kit and love it as well. Thanks Mike
@andygilbert18773 жыл бұрын
When I started I had a socket for 18mm plugs (thread size, can’t remember the socket size) which I used quite often on Villiers engines. This was 1975, on various Army kit.
@bryanbeane73285 жыл бұрын
If I remember right my old Yamaha YFZ 450 quad was a 14mm plug lol reason why I had one way back when.
@chrispollock75075 жыл бұрын
LOL about 2 months ago our shop had a Toyota Matrix in for a turn up that required a 14mm socket. Well our newer junior tech took a 5/8 socket and manage to wedge it into the hemi tube, so much that it was like a pressed fit. 3 tech and 2 hours later we got it out!
@flatratemaster5 жыл бұрын
BTDT, it sucks
@svengrootendorst2875 жыл бұрын
Thanks for the info. Last week I changed the spark plugs from my '08 bmw 320 and found it odd that the plugs didn't go in straight so I was a little bit nervous about cross threading.
@anthonygm855 жыл бұрын
Perfect topic, I just ran in to spark plug sockets problems on some old motorcycles I'm working. I've my 5/8&13/16 for years,ineed to buy like 6 new sockets metric and sae ones 14,18 11/16 I'll be need multiple styles of each
@richardsawdon34014 жыл бұрын
I appreciate your video. A few of the spark plug sockets that you demonstrated had an extra drive hex in addition to the female square connection fitting for the ratchet. I'm wondering if anyone has found it useful to turn these spark plug sockets by wrench instead of ratchet because of some reason, such as a clearance issue? Thanks for any information.
@Fordrally895 жыл бұрын
I've broken spark plugs with the magnetic sockets...maybe it's just operator error. Anyways I went back to the traditional rubber insert and no problems
@flatratemaster5 жыл бұрын
I haven't warranted any of the Matco set ye
@Billdavis19745 жыл бұрын
Bought a set of those Matco magnetic spark plug sockets a couple weeks ago, best ones I’ve ever used!!
@flatratemaster5 жыл бұрын
Love it
@mikeprice83072 жыл бұрын
Are they thin wall?
@Billdavis19742 жыл бұрын
No they are like standard spark plug socket
@feildcar4578 Жыл бұрын
I have a set of Schwaben spark plug sockets they also work very well and I actually prefer them over my matco ones.
@mecalpsha44735 жыл бұрын
Don't forget *18MM* for us who work in motorcycle shops
@vicm6945 жыл бұрын
Don't get me started on Honda boat engine 18mm plugs. I had to grid the crap out of a socket to get it to fit.
@mecalpsha44735 жыл бұрын
@@vicm694 the Snap-on one is much slimmer profile
@Jordan-ym5gf5 жыл бұрын
I've had 7/8 before too lol
@pelotas565 жыл бұрын
I remember doing my first sp plugs on a mini Cooper, way back when I ain't even know it was a 14mm 12point. Snappy was the only one that had it and yeah that socket was stupid expensive 😭
@michaelsieber66014 жыл бұрын
5/8 and 9/16 are what i use the most tune ups on tritons are my money maker as long as I don’t have to bust out the lisle extractor
@awilson56365 жыл бұрын
If you work on Chevy Express vans a double swivel 5/8 socket can get about 7 of 8 spark plugs through the wheel well on 4.8s, 6.0s, etc. And the last one I get with a regular 5/8 plug socket and small extension from below with a ratchet.
@mecalpsha44735 жыл бұрын
What brand socket you use them?
@awilson56365 жыл бұрын
I use a Snap-On double swivel 5/8 spark plug socket, but other brands make double swivel spark plug sockets as well.
@dickskinnersshopandsnapont67185 жыл бұрын
I might have to start going to the Macko truck they got some nice little doodads here in there
@shawnz2415 жыл бұрын
I have the Matco swivel set and those 13/16 oes are useless but I love the set. My Matco dealer gave me the 14mm 12 pointer but Matco should rethink that set.
@JUSTINATV5 жыл бұрын
Sunex makes a pretty good kit. Great video and topic!
@joehyundaitech79615 жыл бұрын
I only use 5/8 because I only do spark plug replacements on fords I have been been working on fords since 1997 and that is all I have ever needed but I also only do them on the focus and the escorts because there mine . at my dealership I dont do them because I dont get paid enough for tuneups or brake jobs
@du8864 жыл бұрын
I've only ever changed plugs on old junk so 13/16 is the only spark plug socket i've ever had lol
@P.A.C.E.automotive2 жыл бұрын
9/16~14.3mm. Great content 👍
@ZERONEINNOVATIONS8 ай бұрын
I have 5/8 short swivel powerbuilt rubber one but I don't like it. Rubber portion comes out and get stuck on plug top all the time. Koken is selling the plug socket with metal clip inside and I heard it's better than magnetic ones. Also, I want the one that comes with a extension already permanently attached to it. 6 out of 8 times, my 3/8 extension come off just after the sparkplug socket and I have to use a small needle nose pliers to remove it from plug hole. (Ford 4.6L)
@niteninja01335 жыл бұрын
Can you do a video on the difference between a mechanic and technician?
@Itsdazeni5 жыл бұрын
Good to know about those 14 mm sockets thanks frm👍
@eliasaviles90692 жыл бұрын
the chevy equinox uses a 9/16" socket for spark plugs though.
@Hipsters_N_Hippies5 жыл бұрын
A/C! I fully understand where your coming from...sadly.
@88FCRX75 жыл бұрын
Hey FRM or anyone else really but what uses 18mm spark plugs sockets is that like a lawnmower or yard equipment spark plug
@Ferkle8712 жыл бұрын
Now here's my question,is the rubber in the socket warrantied by snap on or would I have to buy inserts to use as time goes on?
@billhanley935 жыл бұрын
9/16 is used on some Toyota’s and gms too
@niteninja01335 жыл бұрын
I have a duralast one that i love and its cheap, and lifetime warranty. Has a magnet and not that stupid rubber crap inside there that sticks to the plug
@GCraigmile5 жыл бұрын
Just like you I have many many spark plug socket kit or master kit.
@christopherallencomer57382 ай бұрын
Thx. God bless.
@XXGunzNClipzXx5 жыл бұрын
Lol what are the odds I was just like “wtf “ when I checked my gfs 16 Civic and it’s a 14mm lol I had to use the paper inside the socket method to guide it back in xD
@mikeeustice44525 жыл бұрын
And dont forget snapon made an offset 5/8 socket for only one plug on one engine in one line of truck it was the center plug in the drivers head on the 4.3 liter gm in the s10 series blazers and pickups due to the steering shaft then they wonder why we all swear.
@briangolas28844 жыл бұрын
Good video. Informative. Thanks for posting.
@therealist66702 жыл бұрын
Soooo is a 12 point spark plug socket better than a 6 point socket?
@cesaraguilar90962 жыл бұрын
Any tips on changing sparkplugs on 4.9v8 cadillac DeVille fwd?
@patrickrich99765 жыл бұрын
The Matco swivel set look like autozone duralast. My main sockets and tools is snap on and Matco but flat rate master if I need something specific for a job I would go to auto zone or advance. Still life time warranty. Working on someone else stuff most time there not going to pay for the tool plus the repair it’s unrealistic
@93sundance5 жыл бұрын
The newer GM 3.0 TT and 3.6 use 14mm.
@nicknicu17875 жыл бұрын
Good to know about those deep holes you have to attack at an angle... LOL!
@ahoorakia3 жыл бұрын
forgot about open socket for car like GM with LT1 engine when there are no room other wise
@juliossntana34143 жыл бұрын
I swear that's how I sound after a long day lol "the ending "
@ifitsnotbrokenfixit11935 жыл бұрын
Great video FRM
@docvince8883 жыл бұрын
hahaha like the way you include your out takes!!!
@GearHeadsGarageChannel5 жыл бұрын
Eghlughelugheeghhhhh!! lol me too FRM it happens all the time especially when Im tired when filming
@garethriley4505 жыл бұрын
Hi. Love the video's. Im in my 30's looking to retrain to be a mechanic. Any tips or advice?
@philh92385 жыл бұрын
what do you do now??
@garethriley4505 жыл бұрын
I'm a chef
@georgebonney905 жыл бұрын
Thx FRM 👍
@christopherbarone36025 жыл бұрын
14 twelve point socket have not seen on yet 30k spark plugs is due to gdi problems
@flatratemaster5 жыл бұрын
And going back to copper cores
@InCountry6970Ай бұрын
No link to buy the set ???
@salvadornevarez7934 Жыл бұрын
Where can I buy the set?
@altonriggs23525 жыл бұрын
Good stuff thanks
@donwilliams4953 жыл бұрын
Is there a flex with a short extension that will work in a 1999 ML320? I had to make one but apparently MB has one listed and maybe other companies. MB part number is 112589010900.
@mrturner695 жыл бұрын
smaller engines use 13/16ths aswell
@robertvinscent65685 жыл бұрын
9/16" for 2009-10 Toyota Corolla also. Or at least I know it is for the Canadian Models.
@joshuamyers31855 жыл бұрын
Canadian GM has 9/16 also...took for ever to get plugs for a Spark (if remember right)....guess the Canadians use them
@nahumdass79783 жыл бұрын
Hey when you do videos can you hold the tool in the frame longer and as your hold it there try not to talk with your hands and shake around the tool in the frame. I would like to get a good look at the scale and details of that tool you are showing
@blakewaddell4515 жыл бұрын
I ran into 18mm on a new car so I had to use a regular socket
@ronaldjohnson1474 Жыл бұрын
As a mechanic in an independent shop, why didn't you mention 18mm spark plug sockets? They don't exist for no reason.
@nitrous07me5 жыл бұрын
“Deep & holes” 🤣
@frugalprepper5 жыл бұрын
Back in the day you also had 3/4 for the weed eaters!
@FishFind30005 жыл бұрын
FrugalPrepper's Garage & Garden pretty sure I still use it.
@frugalprepper5 жыл бұрын
@@FishFind3000 I used mine 2 days ago! Before that is sat in shed toolbox for 3 years though :(
@MrMSA905 жыл бұрын
Some Toyota’s use 9/16 spark plug sockets
@garyvickers49375 жыл бұрын
Hahaha i like the ending
@DriveShaftDrew5 жыл бұрын
thumbs up and shared yes sir great collection forsure but im sure there are a lot more out there like for smaller engines chainsaws weed eaters, lawn mowers and other stuff all depends what you work on right i know for myself i have a few specialized spark plug sockets for espar units and refers as well
@TonupTodd2 жыл бұрын
I now own a 14mm and a 9/16 in... and I'm not sure why. LOL
@chrischiampo76475 жыл бұрын
3/4 in My Lawn Mower FRM 🙈🙁🥺
@foodskewed91975 жыл бұрын
Kia and Hyundai used 13/16” too
@joshuamyers31855 жыл бұрын
Haven't seen in long time...older stuff (metal intakes) used them
@foodskewed91975 жыл бұрын
That’s why I chose the word “used” past tense
@ronijr49183 жыл бұрын
No they don't it's 5/8
@foodskewed91973 жыл бұрын
@@ronijr4918 their older stuff did. I’ve done several. It thanks for your input
@ronijr49183 жыл бұрын
@@foodskewed9197 Ohhh okay cause I've never worked on a kia older than 2010 so i though you were referring to some what newer models
@Dieseltechbrian5 жыл бұрын
Wish you were doing you tube videos 13 years ago. I would have saved a ton of money
@mikkehdez5 жыл бұрын
That’s what she says you go deep in hos lol
@michaelmobilautodiagnostic67055 жыл бұрын
I bought a Matco spark plug socket set a while back I was wondering if I might of got one with two 9/16 sockets instead of one with a 14mm socket?
@flatratemaster5 жыл бұрын
One 9/16 socket is deeper than the other, why no 14🤷♂️
@ozzstars_cars5 жыл бұрын
I know what it is like to go deep in the hole.
@flatratemaster5 жыл бұрын
😉
@wysetech20005 жыл бұрын
Do you still remember? 😁
@scuba4221235 жыл бұрын
the magnets break up in the gearwrench brand and the pieces can fall into the cylinder
@mecalpsha44735 жыл бұрын
Do they break up pretty fast with normal use, if so I will be the MATCO ones?
@scuba4221235 жыл бұрын
mine broke after a year I had one warrantied but they still hold the plug! I don't have the matco ones but a few snap ons they do work well
@flatratemaster5 жыл бұрын
The matco set i have doesn't have that issue
@mikeprice83072 жыл бұрын
DAMN!
@ironcross4205 жыл бұрын
HAHA, You said Deep Holes. Been there done that.
@Yotataco045 жыл бұрын
Land Rover and Jaguar uses 9/16 because there 3.0 and 5.0L engines are made by Ford.
@kevinbeck6419 Жыл бұрын
13/16 you still use them on Chinese scooters
@Ram2253spd5 жыл бұрын
Here for all the deep in holes comments
@aldonco5 жыл бұрын
What you really need is air conditioning in that shop.
@hunterdenley48385 жыл бұрын
I work on diesels...what is this foreign language lol
@blazebox715 жыл бұрын
5/8 probably the most sold spark plug socket of all time ever lol
@dummkompf3 жыл бұрын
you should really invest in an a/c unit for your shop. You're so sweaty, I can smell you through my screen!