So I am 68 yrs old, my smart ecobee is defective as are neighbors also; I can't pay for labor so changed to this honeywell with your help! Didn't know if I could do it, but I DID IT!! Thank you so much from a senior citizen without experience. I saved more than $350.
@dragonstunna Жыл бұрын
One thing you should mention is how to change the cycling frequency to match your specific heating system. For that thermostat model press the 2 arrow buttons at the same time for 5 seconds; the first setting function (called 5) will change the cycle frequency (2, 3, 5 or 6 times an hour maximum), if you have a steam boiler set this to 2, if you have a hot water boiler set this to 3, gas/oil furnace uses the default 5, and electric furnace should be set to 6. The manual explains more of this and other advanced settings on page 9. This particular setting is really important because if you have a steam boiler it should not be cycling more than twice an hour, by design its not effective at higher cycle rates.
@joeyosetek3 жыл бұрын
That was a very smart idea with the plate. Thanks for sharing.
@EverydayHomeRepairs3 жыл бұрын
Thanks Joey!
@MinecraftPro97k3 жыл бұрын
Absolutely love your profile pic
@patsingleton48597 ай бұрын
Thank you so much for this easy to understand video. I am a new DIYer, and I was able to install the thermostat with no problems. The switchplate covered the imperfections perfectly!
@punkymunkin Жыл бұрын
This was perfect - covers all the installation issues in easy to understand laymen's terms.
@ForrestTrottierАй бұрын
Very professional video and great explanation of the process.
@1942nn3 жыл бұрын
This is the best video showing how to install this thermostat correctly. The large wall plate is a great idea. I do not have this issue as I can sand the drywall and paint over with exact same color (saved from a recent home painting job). The large wall plate makes this look better though. I love it.
@EverydayHomeRepairs3 жыл бұрын
Thanks Kim!
@plhm333 жыл бұрын
Thank you...Excellent and cost effective way to cover wall damage. We followed your directions exactly with no issues, and installed the same thermostat.
@EverydayHomeRepairs3 жыл бұрын
Perfect, glad the solution worked for you 👍
@SsCsBs3 жыл бұрын
Hi, I just wanted to thank you so very much for making this video which helped me change my thermostat. Was waiting on a tech but I love accomplishing these repairs by myself so much easier with your help! Much appreciated :)
@EverydayHomeRepairs3 жыл бұрын
Nice, way to take the initiative and save some money. We have a lot more videos out there what's next on the list 😉
@SsCsBs3 жыл бұрын
@@EverydayHomeRepairs Yes! Thank you so much! My beloved dad would've been proud lol. I subscribed & will look to see what else needs repair :)
@lx950202 жыл бұрын
Just swapped out my thermostat. The swap is the easy part....the difficult part was figuring out where to put the drywall anchos because of all the damage to the sheetrock and the wacky position of the stud. I followed your instruction and my thermostat is working great and looks great with the wall plate. Thank you for this video!!!
@bobsleep71543 жыл бұрын
The installation of the electrical switch plate was a wonderful fix to the problem when switching between thermostats. Thank you for sharing.
@EverydayHomeRepairs3 жыл бұрын
You're welcome!
@lesleopold98933 жыл бұрын
I really find your simple fixes that add value to my home and answer a common issues!
@EverydayHomeRepairs3 жыл бұрын
Thanks Les, glad you are finding value and we will keep the videos coming 👍
@skim68982 жыл бұрын
Thank you for your wonderful teaching. I changed thermostat without technician's help. God bless you!!! 🙂♥️🙏
@BryanTorok2 жыл бұрын
Instead of drilling MORE holes and putting in more screw, I suggest using 3M Command Adhesive strips. They are designed for hanging pictures, so they are more than strong enough for holding a thermostat. And, they can be removed without damaging the wall. Also, I don't get why when people are painting they don't remove the thermostat, switch and outlet covers. It takes about the same amount of time as using masking tape and gives a much nicer job. In the case of the thermostat it is light enough that one could leave it hanging by the wires until the paint dries.
@leighbratcher19982 жыл бұрын
Just finished swapping, installing my new WIFI thermostat, your hack with the wall plate is great. Thank you!
@BryanTorok2 жыл бұрын
Great idea for covering the wall damage. Also, switch plates do come in various sizes. So, if you need to cover a larger area it is likely you can get a larger plate.
@jim7smith2 жыл бұрын
Totally awesome tip on the wall plate cover-up! I'm stealing that technique right NOW.
@fredsanford3362 жыл бұрын
Your simple fix saved our marriage. Thank you.
@kathyjurgens7153 Жыл бұрын
Thank you for such a clear and watchable tutorial. Very helpful and much appreciated.
@allencoke11277 ай бұрын
Thanks for making this video available brother! I see now what my wiring mistake was for my A/C unit blew hot. Fixed now 👌
@richbarb63533 ай бұрын
I was going to cut a piece of indoor paneling as the replacement backing, but I like your idea much better.
@gstamp893 жыл бұрын
Of course I got a faulty one and the screen never lit up with numbers at all when I put the batteries in. I know you weren't thinking that's what you were demoing with this video, but that's what I came here for so thanks man! Good idea with the light switch plate too!
@EverydayHomeRepairs3 жыл бұрын
Thanks for the feedback Greg 👍
@steveschultze1612 жыл бұрын
Love it. I had to do this with my downstairs thermostat. Looks great. Thanks for the video.
@gordongustafson96862 жыл бұрын
Great idea using the triple switch plate. Thanks!
@Trainspotting9442 жыл бұрын
Great idea man thanks for the video. So much cheaper than buying the ones meant for the thermostats at $10 and up apiece. Appreciate it.
@EverydayHomeRepairs2 жыл бұрын
Happy to help!
@nunyabiz761811 ай бұрын
So many questions on wiring this thermostat and people left without replies from the host.
@frankligas22492 жыл бұрын
Timestamp 7:14 When installing batteries, I would recomend to put a piece of tape on the back or bottom of the thermostat with a date on it indicating when the batteries were last changed.
@anthonyheak3479 Жыл бұрын
Great trick/idea with the light switch cover. Thanks for sharing! I will use this trick next time.
@garygrella17232 жыл бұрын
Hey , that switch plate for mounting is a great idea. Thanks , it solves my problem .
@nguoidonghuong2 жыл бұрын
Wonderful and thanks for the video. I like the idea with the plate. I wish I saw your video earlier, just spent $28.00 CAD for the plate.
@EverydayHomeRepairs2 жыл бұрын
😂
@extence57 Жыл бұрын
Do you have to remove the jumper to install red wire? I noticed the jumper is still in place but I cannot Turn the screw with a jumper in place. Thanks.
@vincecarere2 жыл бұрын
Wow! this is exactly what I've been searching for. Thanks
@cpsadp992 жыл бұрын
Such a clever idea. I am installing the same model and I think I have the same paint problem. I am doing this for sure. Thanks for posting the video. Cheers
@JMatthewTurner3 жыл бұрын
This video is flawless.
@jasonbwilliamson3 жыл бұрын
Nice video and clear instruction. You got a new subscriber and I'm going to install this exact thermostat this weekend.
@EverydayHomeRepairs3 жыл бұрын
Hey Jason, best of luck on the project!
@SimilakChild9 ай бұрын
the light switch plate was a great idea! i was thinking a thin piece of wood painted white.
@lovet66262 жыл бұрын
Thank you for the video. However, my old thermostat has a total of 7 existing wires: Green(G),Yellow(Y),White(W2),Red(RH)with jumper(RC), Orange(O/B),Blue(C) and Black(W/E). The Honeywell thermostat RTH2300B has B,O,G,Y,W, NOT USED, R & RC Does it mean that this thermostat RTH2300B will not work for me? if it does, then where the Blue(C) and Black(W/E) should be connected to? Please advise. Thank you
@amandablair56322 жыл бұрын
That was very thorough
@gbinman Жыл бұрын
good idea. I was a little surprised that you didn't use flat headed screws to mount the plate to provide a flush surface.
@LarryLawfer Жыл бұрын
Thanks for your help, but I have one more question. The wiring in my house is old and I dont have color coded wires and I don't have 4 wires. I only have two. One is still hooked into the base plate and one is loose. I need to know where to connect the loose one. Any help with this?
@renecuevas41282 жыл бұрын
tnk u great idea. never think posible but u did it nice n easy. tnk u bro. blessings from fl. we never use heat here😎
@CrisVazJr Жыл бұрын
Great job, love the hacks, will definitely be using them!
@vincemorath6762 жыл бұрын
Clever solution. Thanks for the video.
@homestar929 ай бұрын
You could make this even cleaner by cutting away drywall, putting in a 3-gang low-voltage box, and using a blank 3-gang plate with a hole drilled in the middle for the thermostat wire (it's all low-voltage so the field modification of the plate shouldn't matter at all in terms of code). This gives a secure mounting point where the plate could be replaced in all sorts of neat ways. You could swap it for a different color plate, or a metal one. The possibilities are endless. Obviously in this case, the stud in the way made that option not viable. But if the damaged area doesn't intersect with a stud, installing a low-voltage box behind it seems like the ticket.
@jenduffield1963 жыл бұрын
Thanks for this idea!! It looks great!
@EverydayHomeRepairs3 жыл бұрын
Hey Jen, thx!
@nathanielnorthrup7 ай бұрын
Just installed mine using your video. Thanks for the help! Also, my yellow and blue wires are backward too....any idea why they do that?
@wesleychurch796910 ай бұрын
I have a old house. When I removed the old theromost an black and white was connected. However, I found a red as well. I have this exact thermostat, can you tell me what wire I should attach where?
@jerrymontalbano3222 Жыл бұрын
Thanks, you were very thorough. One thing always comes to mind and what if you should have a "blue" wire and there's no "Bl" etc. for it? Do you discard it with a piece of end taping? It's amazing, that this Honeywell 2300 only supports the batteries to keep the thermostat working and the bluewire probably kept it on.
@MinecraftPro97k3 жыл бұрын
Yes, perfect!
@abiesilvers494410 ай бұрын
Hi! Great video! I had my old thermostat (white and rogers) which I removed because it was defected and the temperature I kept setting it to would auto drop form 71 to 62 and the heat would never turn on. I followed your instructions and put the yellow wire to W and the red wire to RC as per previous thermostat. Now the heat turned on but the thermostat isn’t controlling it. It won’t let me turn it off or it won’t follow the temperature i am setting. But it is reading the temperature in the room. Did I do something wrong?
@marshallandroxy3 ай бұрын
Thank you for the video - I have a problem - When running my upstairs air conditioner, the induction fan cycles up and runs for a minute, then turns off - repeats a few minutes later until a/c turns off. From what I've read induction fan shouldn't be turning on if the a/c is running (it doesn't on my downstairs unit). Unit is running fine otherwise, red light on circuit board is solid (no errors). Ideas as to why the induction fan cycles off/on when running a/c? Only difference in mine here is that Ive got red into RC and a jumper between RC and R.
@daverodriguez85962 жыл бұрын
Thanks for this video. I am having trouble with adjusting the thermostat temperature to 80. It starts at 68, but when i press the up arrow to raise the temp it jumps immediately back down to 68 degrees. Any idea how I can remedy that? Thanks
@MrLeona0172 ай бұрын
Good afternoon
@PatSchreibeis21 күн бұрын
Of course, I had to have an old thermostat that has wires that this model of Honeywell doesn't support (W2). Just my luck. Nice video though
@luismiguelramirez24892 ай бұрын
Very good video I have 5 wires white, red, yellow green and black. You have blue and I dont and you don’t have yellow,😮 please tell me what should I do? And should I switch it to electric or heat pump? Because is on gas or oil thank you
@tonysgarlatti3611 ай бұрын
Great idea! Thanks for the tip!
@monicaballentine28252 жыл бұрын
Ty my bf ripped it out I need put it back ty ty I appreciate it
@EverydayHomeRepairs2 жыл бұрын
Happy to help 👍
@indistinctchatter66773 жыл бұрын
Brilliant. The official backer plate costs $18 and has to be ordered. This looks better!
@EverydayHomeRepairs3 жыл бұрын
Yeah, I was pleased with the result. Best of luck on your project 👍
@jefferyhicks36783 жыл бұрын
Thanks for the video! I'm having an issue with my trane touchscreen thermostat, I have a package trane heat pump. When the outside temperature falls below 40deg, my pump struggles to keep up and I know the the auxiliary should be kicking in but it doesn't. I have to turn on the emergency heat before the temperature will come back up. I don't think the thermostat is wired correctly, any help would be greatly appreciated 👍
@EverydayHomeRepairs3 жыл бұрын
Hey Jeff, I am pretty limited on my heat pump knowledge but it is my understanding that a properly wired thermostat should kick in with supplemental (emergency) heat if the temp is close or below freezing. You could investigate a bit more the wiring diagrams online and compare to your setup or just call in a local HVAC to do a quick check. Usually this should only be a minimum charge of $75 - $100. Best of luck!
@lindaloftus87802 жыл бұрын
Thank you for video. When I installed new honeywell thermostat I wired it according to the color coding and could only get heat. When switching to cool I also got heat. Maybe connecting the blue wire to y I can get a/c to work.
@MRMSW-we2bk Жыл бұрын
Awesome job! Thank you!
@leeroy4188 Жыл бұрын
I don't know where in my circuit breaker the thermostat is connected, can I work on installing with out turning breaker off? Thanks
@EverydayHomeRepairs Жыл бұрын
If you are comfortable you could flip the switch at your furnace and then confirm no power at the thermostat wires with a non contact voltage tester.
@katrinaransom21433 жыл бұрын
Well done.
@dennisbruns3155 Жыл бұрын
You said to connect the blue wire to the Y slot. Did I hear you correctly, since I would think the blue wire would go in the B slot, unless that is for a black wire for wiring with a black?
@fredripley69092 жыл бұрын
Great video , For some reason my fan will not shut off when I install this new thermostat , I have all the wires in the right place ,I have a natural gas furnace with a air conditioner ,I put the switch on "oil,gas " on the back of the thermostat ,however , when I have reached the right temp , the fan just keeps going . Any ideas as to why ?
@user-tm4gx7sv6m Жыл бұрын
Great video, thanks
@beachbums20083 жыл бұрын
The wall switches over you right shoulder do not have a cover plate over them. Just wondering why not.
@EverydayHomeRepairs3 жыл бұрын
Hahaha, good question. This is a condo I am flipping so just in the middle of the remodel.
@crabbymccrabface36582 жыл бұрын
Hello, I bought this thermostat to replace different make and model thermostat. The one I'm replacing had 6 wires. I called the tech support line and was told that it would work if I followed the installation diagram for the 4 wire procedure, taking off the blue and the brown wire. It doesn't work. I have a gas furnace the thermostat switch is on the gas setting. I don't know if I should have taken the jumper off of the thermostat. Also, I noticed that you used the blue wire instead of the yellow regarding the diagram. I did take a photo of the old wire connections and have the old thermostat to describe how they were connected. Any help would be appreciated. Thanks.
@EverydayHomeRepairs2 жыл бұрын
I would go to the furnace and look at the circuit oars to confirm what color wires are connected to each of the terminals on the board. Some times the past technician or DIYer switched up the Comoros causing confusion.
@crabbymccrabface36582 жыл бұрын
@@EverydayHomeRepairs I'll do that. Thank you much.
@sueponder44355 ай бұрын
Do you have any experience installing a Google Nest Power Connector on an electric furnace that doesn't have a control panel? The strip that holds the thermostat wires and furnace wires are on top of the furnace. It's a weird setup because the furnace is what I would say is a half size furnace and then the water heater sits in front of it inside the closet so it's hard to reach. I had no issues installing the actual thermostat but it tells me that it's not strong enough and I may have issues with the batteries draining fast or the furnace may not run as smoothly. I can see the letters on the front side of the strip that hold the thermostat wires but can't see the back side where the furnace wires connect. I have read the instruction for attaching the Power Connect and understand how to do it but without being able to see the back side I'm hesitant to try it. Plus the wires coming out of the furnace attaching to the strip are not the same color as what the thermostat wires are.
@michaelryan2126 Жыл бұрын
Hello I installed the thermostat but had red, green, yellow, white and blue. after connecting it the furnace did not engage and start nor the blower.
@louisdiep56382 жыл бұрын
Hi, Thank you for the video. I tried to replace my bad thermostat with RTH2300B with the same set up as before, which only use Red and Green wires. The White and Black were not used. That said, after I installed with just green and red wires, my boiler didn’t run as programmed. However, when I switched FAN ON, it runs but ignore my settings. It kept burning nonstop. Can you help? Bad thermostat or bad boiler? Thanks Luigi
@wanderlustly3135 ай бұрын
Can I change the green backlight to blue?
@kenanddeniseheaton7808 Жыл бұрын
I only have a white and black wire. Will this product still work? It’s for a gas fireplace.
@anewdawning1 Жыл бұрын
My moms has a yellow wire also. Where does that go?
@KD-mz5xv3 жыл бұрын
amazing hack :) thank you
@EverydayHomeRepairs3 жыл бұрын
No problem, happy to help!
@kennycrosby38303 жыл бұрын
I have a 6 wire thermostat need the wiring sequence
@kenneth07953 жыл бұрын
Same here. I have 7 different colors, ahhhhhhh
@McmM-cv9sb Жыл бұрын
I like it good job 👍
@juliebales67463 жыл бұрын
GREAT info
@EverydayHomeRepairs3 жыл бұрын
Thanks for watching!
@Glorksnork2 жыл бұрын
If I have both an RH and RC wire do I just put them in their respected slots?
@DuyDepTraiPhoBaTrieu2 жыл бұрын
Honeywell needs to sell their own version of backplate, I can't find anywhere lol.
@misodinamosa Жыл бұрын
Thank you!
@mauriciorivas4674 Жыл бұрын
I have i thermostat with only two wires and only gas heat can i installed those heat only honeywell?
@zloungeact2 жыл бұрын
Great video
@michaelhodgson1201 Жыл бұрын
My old furnace has 3 wires, 2 white one black to a mercury system. Will this work on my old system. ? 2:34
@magdalenas8713Ай бұрын
Not so much how to install Honeywell or any other thermostat - this video is: if everything is perfect and you already know how to install and wire the unit then this is how to make your wall look pretty. Does not help me install a functional unit that gets my system running but does help me ‘install’ the plastic unit casing in a manner that looks pretty.
@yournext20128 ай бұрын
I have a black wire instead of blue do i put in the Y slot
@user-lk2hn3pw2e8 ай бұрын
I hooked up all the wires to my new thermostat did the things that says to do but still will not come on
@user-lk2hn3pw2e8 ай бұрын
My Honeywell rth2300 does not work after I installed it on the wall
@fighting4022 жыл бұрын
Do I got to set a time for each day? Or can I keep heat running on same temperature each day
@norlee29152 жыл бұрын
My old thermostat have combine OB. This 2300 doesn't. So wire the OB to W?
@Espresso1393 жыл бұрын
My existing stat has 5 wires: RC, W, Y, G, and C Is the unit you installed compatible with this configuration?
@yorgilikas30292 жыл бұрын
Good job! Thanks
@MarianoAgaraFernandez2 ай бұрын
Hello, how are you? Is it possible to replace a Honeywell TH1110D1000 device (with 5 colors of cables, I have the other color C) with this device? I have a hot/cold unit with 2 Honeywell TH1110D1000 controllers, but my intention is to replace only one. Regards
@gunit68153 жыл бұрын
I only have two wires running to my thermostat. Will this work for our furnace?
@EverydayHomeRepairs3 жыл бұрын
Assuming the thermostat only controls heat and not AC? If so, it should work 👍
@yvonnesavoie7474 Жыл бұрын
Where do I put wires that are green, red, black & blue
@rogermcgrady176328 күн бұрын
If there's no white but it's black. Where does the black wire go. No ac unit
@100vg2 жыл бұрын
Pretty clever!
@linuslejeune1318 Жыл бұрын
What if there is no C terminal for a blue wire
@universalpressurecleaningp1197 Жыл бұрын
Do we need to leave the jumper wire on to install for the AC
@chloegirl5899 Жыл бұрын
I can't get the red wire to go in, the screw won't back out.