Evinrude E-tec 25

[@vangogvincent818]

Четкий мотор. Тоже такой хочу. Ты счастливчик

[@danmurphy1994]

Dude those are some badass maneuvers you're doin on such a small boat. I tried that in a 1550 V hull (with 4 people about 170lbs each) with like a 7.5 hp mercury i believe and the rear left corner began filling up with water when I banked too hard

[@Idk154]

7.5?! You mean 75 right?

[@caseysummersett6243]

Thanks for the info. I did buy a 25 etec to replace my 15hp 4 stroke yamaha. It was a great move all around.

[@Turbotalkin]

Top speed?

[@johnrhodes4949]

Thats a neat boat i like the design!

[@geetarnut]

I'M A 28 YEAR OUTBOARD MOTOR TECH AND JOHNSON AND EVINRUDE 25 AND 35 MOTORS ARE VIRTUALLY THE BEST! THE ONLY OTHER 25 I LIKE IS THE TWIN-CARB YAMAHA MOTOR! IT LEAVES THE PACK BEHIND!!!

[@samdittmar5142]

Sonny Cannon the old mercury 25 hp 2 strokes were the best 25 on the market

[@andrewstevens9246]

Sonny Cannon don’t forget about the good ole 9.9 Johnson! I have 2 of the 1979 models and wouldn’t trade either of them for a new 9.9 Mercury. The more I run them the better they run.

[@jimjohnson2576]

What about the 2013 50 HP Etec (E50DTLAFA)? Thanks

[@MrSp8282]

Thanks Kyle.

[@MrSp8282]

It's not a jackplate but a Tilt and Trim unit. CMC PT-35 is what it is. 5.5" setback. Thanks

[@garyspetzman1440]

How do you like the cmc pt-35? I have the same motor.

[@meganknowles4754]

one thing do not change your pitch from aluminum when going to stainless. it will decrease your power and 0ef9r, less . been in boat industries for almost 15 years

[@kylecomeaux553]

Thats a real nice boat.

[@alecfranklin522]

dose yours have trim I am going to by a short shaft but I can't find one with trim. I want to be able to get it out of the water for shallow water

[@MrSp8282]

It is a CMC Pt-35 aftermarket tilt & trim unit.

[@alecfranklin522]

Is the switch still at the end of the tiller

[@MrSp8282]

Alec Franklin yes it is. I ordered the factory switch and wired it myself. It was a pain but works great

[@MrSp8282]

Current River Marine in Doniphan, MO

[@caseywells2657]

I just fried a Mercury 25, am looking seriously at this Evinrude. Is that a jack plate on your boat. I have not seen one on a 1546 before, thats the boat I have. It looks awesome. Can you tell me more about the jack plate? Thanks

[@codyi]

Still running good? Any problems so far?

[@AirlinersHD]

What is fuel consumption per hour at full throttle?

[@chrisma9056]

Nice I want 1 now

[@MrSp8282]

I get around 27 with tunnel hull boat. Around 31 with regular boat

[@kevinahmir5070]

Instablaster.

[@bryansmith7765]

Nice boat and motor. I had a Alumacraft MV 15/46 tunnel hull with a 25hp yamaha with a 13 pitch powertech SS prop on it. One thing I liked about the powertech props is that the blades where cupped to help prevent cavitation(bubbles that cause your prop to freely spin). I loved my boat, if I was floatin, I was runnin. How do you like your Etec? I have always like Evinrude/Johnson's but ever since BRP bought them, I have always heard they went down hill. Still better than Mercuries. Wouldnt own a Mercury if you gave it to me....lol.

[@MrSp8282]

Bryan Smith We love our motor. Great power and decent speed

[@950hpvette]

I have a 25 hp mercury sea pro 2 stroke on a 14'3" Princecraft Yukon utility aluminum boat. dry weight 240 pounds. I have a stock 10x13" pitch 3 blade aluminum prop. If I want to go to a stainless steel prop could I keep it the same or would I have to go to a 10x12" pitch bc the stainless weighs more? thanx.

[@MrSp8282]

Stephen, it really depends on what rpm's you are turning at WOT with your normal load. Generally the rule of thumb is to drop 1" pitch when switching from aluminum to stainless. I would recommend getting a tiny tach to verify your rpm's at WOT to set your pitch properly.

[@BigGoch02]

What size transom? 15" or 20" not sure which to get with a short shaft motor, and I don't have a jack plate. Maybe getting a trim plate like yours

[@MrSp8282]

It depends on what size transom your boat has. If the transom is 16" then short shaft motor, if 20-21" use the long shaft motor

[@EV1NRUDE]

Why do you even have that trolling motor?? Thata the engine u need!

[@BigKahuna_outdoors]

Nice was looking for a upgrade. Notice the tiny tach how many RPM's at WOT? What is your input on this engine?

[@MrSp8282]

I set it up to run near max rpm with me only because I hardly ever run it by myself. If I was only looking for speed, then 13 pitch would be almost ideal. The motor is great, good on gas, plenty of power for me. Looking for more speed/power, then get a 40 or 50 hp 😀

[@squidinkRC]

Hey, My dealer said i need a fuel pump after it not running reliably, Its a 2011 25 hp. What should I do? I'm very mechanically inclined.

[@MrSp8282]

Squidink if you can replace it, then do it. Mine was under warranty.

[@squidinkRC]

Shogun82 should I trust their diagnosis? Is there a way to rebuild it? Should I simply buy a new fuel/ vapor pump? They are around $300 I want to make sure I’m fixing it correctly to solve my issue. Thankyou for your help

[@MrSp8282]

Squidink if they’re a reputable dealer, they should’ve hooked it up to the exec software to read error codes. If not, you’d have to have the tools and knowledge to diagnose yourself. I don’t think the pump is rebuildable like the older days unfortunately.

[@Mrfishingexpert]

Thats a cool little rig for creeks like that. We have a 20ft Stratos 201 Pro Elite with a 225hp Evinrude Vindicator, but we also have those little 8ft bass raiders with a 30lb thrust Minnekota. We are looking to get like a 3hp outboard for it, but dont really want a Mercury. Do you know if they make Evinrude, Johnson, or Yamaha in a 2.5hp, or 3hp?

[@northamericanproductions]

Dalton Keels No, evinrude does not make a true evinrude under 15hp. Evinrude and mercury both use tohatsu engines in their 15hp and under portable engine class. You have to buy an etec to own a evinrude engine. "Note" evinrude does build a 15hp kicker though. I own a 25hp etec and love it. Great engine.

[@Wingnut353]

They 15, 25 and 30HP e-tec all have the same block so weigh the same 150-180lb depending on accessories.

[@thomasmiles8308]

What was the price of this motor

[@MrSp8282]

around $3300 out the door.

[@BigGoch02]

What size transom do you have? And shaft size motor?

[@MrSp8282]

16" transom with tunnel hull. 15" shaft motor

[@caseysummersett6243]

Im thinking about picking up a 25 etec. what kind of speed are you pushing wide open?

[@johns2453]

a fuel pump replacement on a new motor...i have a 25 dt suzuki thats 21 years old and had no issues at all.. general maintenance. lets see if that e-tec can go that long. i seriously doubt it.

[@KennyGarland]

big difference is anything made 20+ years ago had more hands on inspection during manufacturing and qualified journeymen on the line. today most manufacturers employ cheap labor techs who couldn't care less about a thousandth of an inch.

[@kirkbourgeois2560]

Did it come with electric trim

[@MrSp8282]

That’s an aftermarket tilt/trim unit

[@GoofieNewfie69]

why do they call it a tunnel hull if it's a flat bottomed boat

[@MrSp8282]

Mazda rx7 Pocket tunnel would be a more accurate term. Tunnel is located in center and extends about 3 feet from stern.

[@TheVinylSock]

Where did you buy the motor for 3300$?

[@danielready22able]

thats some nice shit boy

[@dronerz5172]

Those are some sharp turns 😂😂😭

[@EV1NRUDE]

Yeah

[@jannowak4977]

Fajniejsze niż czterosuwowy.

[@Marciorlopes]

Amigo qual e a velocidade final km

[@MrSp8282]

Marcio r. lopes about 43 kph

[@levijones1874]

Sold

[@АлександрХрамов-г7ч]

Запуск хороший, но почему то чувствуется, что от шума и вибрации никуда не деться. Печально, что нет ДУ, затекает спина при долгой езде.

[@Moturnak]

Александр Храмов .....затекает спина......КУПИ САМОЕ ДЕШЕВОЕ КРЕСЛО ОФИСНОЕ ДЛЯ КОМПА,СНИМИ С НЕГО СПИНКУ И ЕСЛИ РУКИ НЕ В ЖОПЕ ПРИМАСТЫРЬ К ЛОДКЕ....цена вопроса 2тыс руб...ВСЕ!!!! Или тупо будем сидеть и писать ,что мотор на румпеле и спина устает.....САМОМУ ТО НЕ СМЕШНО ТАКОЕ ПЕЧАТАТЬ?

[@Moturnak]

Это из серии-"ВСЕ ПЛОХО! МНОГО ЕДЫ И ТАРЕЛКИ БОЛЬШИЕ!"

[@geetarnut]

WHAT RIVER IS THIS. WHAT STATE???

[@MrSp8282]

It's called Big Slough Ditch that connects to the St. Francis river in NE AR.

[@thomasmiles8308]

Top speed?

[@yahatinda]

Watch out for the Chrocabas hanging out alon dat bayou boy. dey come out at twilight and can strip the flesh offen a big man in tre minnits.

[@Baley345c]

How fast

[@MrSp8282]

About 28mph with tunnel hull 4 blade. About 31 on regular hull with 3 blade

[@drakemccarthy7312]

how slow does it troll down too?

[@MrSp8282]

Drake McCarthy I've never clocked it but it slows down pretty low

[@dylanfournet6080]

talk about turn and burn

[@AAE-cg1il]

Keep that etec pampered………there are no more coming.

[@angelawelch2532]

That thing is moving SON for a 25 horse

[@BigGoch02]

Sweet thanks!

[@MrSp8282]

Powertech SRA4 12 pitch

[@terezinhaalvestereza7964]

ai sim isso que es motor

[@rezh.6193]

A Honda would start first time.

[@MrSp8282]

Rez J operator error. In gear start protection working great

[@brandonmurphy4657]

Made in china

[@yamahabradley]

If its in forward gear the engine should not roll over.

[@MrSp8282]

Robert Bradley it will roll over but won't start

[@rondouglas584]

Beware of this motors . Had one for 8 years . An final cut ties with the company .

[@MrP020372]

Brilliant!