How To Connect a PA System with a Powered Subwoofer & Audio Mixer

[@justinreilly3107]

Not sure if you mentioned it but I just hooked up a sub onto a bus channel and it works great because I have independent control over the volume of the sub on each channel of my mixer using the monitor 1 send

[@expertisland]

It's always a great way to get more control over the subwoofer

[@cathyharrity8050]

I like the combination of 2. Alto ts412 with the affordable but excellent quality Harbinger S12 subwoofer. All around great sound and under $1,200 for 2 speakers, 2 stands one subwoofer and all cables needed. Decision based on watching your excellent tutorials

[@av7809]

How do you like the alto subs? I recently bought a pair of Harbingr 12” pa’s next are the subs

[@cathyharrity8050]

@@av7809 Altos cost 100 hundred dollars more per speakers 🔊 but are rated much higher than Harbinger. However their 12" speakers and subwoofer are very good especially the new Bluetooth Vari lineup and unless you're playing for crowds of over 60 people the subwoofer does an excellent job and ties in with the Altos just fine at $120 less than the Altos that's why I bought their subwoofer. The Harbinger veri V2312 were not as clear outside and didn't carry the full sound the Altos do. That's why I got the Altos TS412 PA speakers. I thought the Harbinger Subwoofer was enough for my needs and saved me a bit of money. The Vari 2312 is still a great buy for the money and probably the best option in its price range 😀

[@jamesbrown-bp7sr]

Never mind, I figured it out. The video was extremely helpful. Just starting out as well.

[@jamesm.8362]

Great instructional video! Clear, Precise, Informative! Thank you!

[@expertisland]

Thank You 🌴 Glad it was helpful!

[@izzyrod5124]

What if you have 2 12 inch subs instead of one.

[@cathyharrity8050]

What microphone 🎤 boom do you use. Like all your, this was no exception "excellent" clear informative tutorials. The guy to go to!

[@coachmatt5245]

I just got myself some used Yorkvile NX55P speakers - I need some help on how to setup 2 Yorkville NX55P speakers with a Yamaha MG10 Mixer and a DJ Controller - Numark Mixtrack pro - I helping my son getting this setup for his starting role to become a DJ music services Dj setup - Mixtrack Pro controller 2 PA Power speakers Yorkville NX55p Mixer - Yamaha MG10 Cables requirement - Currently 2 XLR cables - Male/female ends - RCA cables with 1/4 " ends - How to connect Yorkville 2 NX55p speakers to a Yamaha MG10 with a Dj Controller

[@LionofJudahministriesintl]

Hi. I learnt a lot from ur channel. Can u pls make a video how to connect 4 tops and 2 bass?

[@rdavkid]

This would be a great video. I have 2 tops and 1 sub mad looking to get 2 more top and 1 more sub

[@73prd]

I always thought you run your subs from aux send from desk and your 2 main speakers out of mains? That way u have individual volume control over mains n subs, setting them.up like u have means when u turn up the mains the sub volume raises also???? I'm so confused

[@ParanormalResponse]

Subs will take on all the low frequencies it is rated for, It will throw all other frequencies not in its range to the mains. The mains will then take the full range frequencies through the amp one ( class D) and the Higher frequencies through Amp two. (A/B ) Built in , powered speakers.

[@73prd]

@@ParanormalResponse so should I daisy chain my subs with my main speakers or separately

[@Yotubez]

So if I have 2 subwoofers do I just take an xlr from the mixer to an in at the sub and send an out to the in of the speaker and repeat the same with the other space at the mixer for the other sub and top?

[@carlrathburn8722]

Thank you very much for your video! Very helpful! How much for everything that you used in this videos including all speakers, the mixer and xlr's?

[@williamrivera6818]

Great job thank you so much

[@fainiac4201126]

If I had the mixer going to 2 separate subs, then went out from each sub to individual top speakers. Where would I connect another speaker for a monitor? Out from the top speaker or out from the sub? I am using Alto Professional l subs and Mackie Thump tops.

[@derkleinekaiser]

I've seen other people go from the Audio Mixer Main left and Right and go into the regular PA speaker, and then out to the subwoofer. Essentially, opposite of what you did. Do you recommend that or why do you go from the outs to the subwoofer and then the PA speakers? Anyone can answer.

[@jttruong2681]

I have the sane question as well. And I think I have the answer for that. 1. In this video the subwoofer have crossover and the speaker doesn't? 2. The reason some will go to speaker first because there speaker have crossover but their sub don't. Like mine I just bought 2 alto ts15s and found out they don't have crossover but my ev zlx 12 p speakers have crossover.

[@robertkeller6015]

Youre a gentleman and a scholar thank you for sharing that truly appreciated! If i may ask a question i just purchased a rockville dual band eq and it has 1 sub out xlr▪︎1/4", 2-ins,2-outs for channels1 and 2. My set up consists of 1 Harbinger 18" 2000 series sub, 4-15's 4000 series and 2 -12" 4000 series and last but not least a Harbinger L12 mixer too much to sort with my dyslexia lol,could you please and thank you help with this setup so it will sound as optmium as it could get i would be forever grateful

[@emeteriozamora3235]

i was lucky because i see your new video for set up 1 subwoofer and connect 2 main speakers.yah...i have 2 pa speakers thump 12 inch 1300 watts so.. my question is whats is right power subwoofer for 2 speakers.... something your set up.thank you for sharing your video godbless

[@neilmusician1143]

Please make a video on Live Sound Stage sound system for outdoors. thanks

[@Lamar4ya]

Should I run my single 18 inch sub woofers out of my A15-in Yamaha’s or should I run the 15 inch Yamahas out of the subwoofers or does it make a difference ? , thank you, Lamar

[@sabuandmanju3595]

Well explained

[@expertisland]

Thanks 😊

[@brehoffm]

Does the crossover still have the same effect if I run the wire from mixer, to the top, then to the woofer? Or does that defeat the purpose?

[@enriquegarcia1547]

How would I go about with the purchasing of this complete system? Who should I call? Thanks.

[@goodmanshealth]

I have a similar system and was told to run from the board to the top speakers and then go out of the sub into one of the top speakers. Is there any advantage to going from the sub first? Also it means using 4 xlr's instead of 3 .

[@blabla494]

Going into the woofer first, then out of the sub into the mains removes the low end from the tops.

[@edgaraleman6053]

Josh burdge is that all it does just remove bass from tops?

[@markmohammed2057]

​@@blabla494How important is this if your tops have dsp and fir filters etc .im in the same pickle i have operas 15 . Will the crossover make them louder?

[@kapisithekid2843]

Amazing tutorial. I have a question. I want to use only one subwoofer and one top. How can I make it possible to have a stereo sound 😊from only these speakers…I was thinking of coming out of the mixer (L&R) into the subwoofer like usual. Then, if I only take a (Left) out from the sub, then into the one top, can I still get both sounds of the (Left & Right)?

[@-TimZambra]

Do you have a video where you look at the subwoofer cross over and getting the balance right with the tops and mixer? I have a Behringer 15" sub and two vonyx 15" tops with a XENYX Q802USB mixer which I run my dj controller, right and left, through the compressor channels.

[@expertisland]

I will be making a Video about the Harbinger 18" subwoofer Soon And will Try to add your Question to the Video.

[@-TimZambra]

@@expertisland Thank you :)

[@djmikeyblair4650]

​@@expertislandhave you made that video yet?? I'm interested in this question as well

[@willvargas4477]

Best daisy chain video!

[@djwildb77]

How about if you want to utilize the Harbinger's true Stereo function? Making the 2310 left the master and the right the linked-in speaker. What cables would be need?

[@expertisland]

I will be making an overview video All about the Vari V2310 Lots to Talk about including the true Stereo function.

[@ameenblue21]

So what happen if you have the harbinger 10s that don’t have adjustments on the back?! There just strictly input

[@brehoffm]

My sub only has one input/output (EV ELX 18). If my mains left and right are stereo, do I lose any low frequencies meant for the opposite channel? Or are the low frequencies in mono so both L and R get the same sound?

[@gillesbuvat5865]

Great video!

[@expertisland]

Thank you.😀

[@DJMaSoySauce]

Thank you! Very helpful!

[@raynger88]

Hello, I have a Mackie ProFX 12v2, 1- Bose Sub1 and 2-Bose S1 pros which I inherited. Please give the proper way to connect my system. Would like to connect my IPhone for music, 1 Shure wireless mic and how to separate my Bose Sub1 with its own control. Thanks in advance!

[@NoOneToldMeThat]

Can I connect a Harbinger subwoofer to Thumper XT Bluetooth speaker - without a mixer? So I’m sending music to the Thumper powered speaker thru Bluetooth - and need to connect the sun. Thumper works awesome I just can’t get any cable combo that allows the sun to work.

[@tonyy815]

Hi , I just got my alto professional 2500 w subwoofer, still waiting for my XLR cables to connect it to my mixer , can I connect this subwoofer to my 2 jbl eon 712 , without the mixer ?

[@jerrysell3139]

Hi. I recently bought a LD System IOCA 18A Sub to compliment my Peavey XRs with Peavey SP Dual 15's. Black Widow Equipped. Non Powered. I need help. Can you tell me the best set-up for this arrangement? I'm at a standstill. Thanks. Jerry S.

[@zdbzdbzdbz]

good instructional vids.. so hooking up a mixer to sub's input and out to mains....you have to run back and forth to the stage to adjust sub's volume?

[@expertisland]

if you have more cables and a mixer with more output options you can always do better.

[@sexychef3333]

Love your videos. Very informative. I'd like to get some input on a system I'm using. Currently running 2 guitars, bass, 3 vocal mics, and drum kick thru a soundcraft ui16. Main outs to a pair of powered Mackie Thrash 215's. Not a bad sound but missing lows. Considering adding a pair of powered Mackie 118s subs. We play anything from small bars to larger banquet halls and outdoor venues. I want to keep things simple as I am running sound from stage. My thought is running main left and right outs to their respective subs and then running out the high pass outputs to the tops. Will that keep the mix from muddying up? Thanks

[@expertisland]

Great setup, I think you're good with both top-down and bottom-up wiring. Double-check the manual to make sure mackie may have a better suggestion

[@nicholasberdugo6346]

How do I connect 2 subs and 4 speakers with my dj controller

[@djmorry8748]

Very hard to get info wiring two active subs in from one aux out or 1 mono out from the mixer!

[@aaronjademusic5197]

I had asked 2 different people at guitar center and I got 2 different answers. Does it really matter if I come out R/L out my mixer to my sub 1st OR to my top powered PA THEN into my sub? The other night I went from top to bottom sub and it sounded alright to me but IDK for technical reasons.

[@nugeman7779]

Can you go from your mixing board to your mains and from the mains to the sub?

[@korospds]

please need help how to contacted Electro-Voice ETX-35P to another EV speaker no sub

[@oleglang5750]

I have EVs ZLX if I want to add an extra m-audio speakers to it I know it needs to be done the through ZLX output. Do I have to enable anything else on the ZLX (does extra speaker considered subwoofer and needs to be enabled)? If yes, how should I set left ZLX and the left M-Audio? Thank you!

[@GreyWolf_444]

I have the same hook up with the exception of my computer and now I hear a high frequency when I turn the faders up do not have a clue what's wrong.

[@IetitaiaSamuela-ew7sj]

What is your speakers are passive, would you connect directly to the amp from the sub output

[@sp-sc2lh]

can I use the main input for sub and control room for tops

[@leesmith2072]

Wouldn’t you keep your sub on a separate channel to your mids so you can adjust the sub without disturbing the other speakers

[@expertisland]

That is a good Add-on I personal like to control the Gain and cross over actively from song to song.

[@Yellowjacket1977]

That makes sense. I really want to control my sub separately from my tops, so how would that be wired through my 100' snake? Currently, I'm sending channels L & R from the mixer through Snake and out of A & B into the sub-speaker L & R as he does here? Then to the tops.

[@Yellowjacket1977]

@@expertisland So are you saying add a separate crossover to be able to split your subs from your tops?

[@ramiromaldonadojr]

Does the limit signal on the sub suppose to stay on because both power light and limit light signal stays on I have 18 inch sub Harbinger

[@ZyberFlix]

Can you plug in subwoofer directly to pa speakers? Without the need for mixer?

[@expertisland]

Yes you Can

[@rhandyyaya9053]

Thanks for making this video. I need your help. I have Harbinger M200BT and trying to hook up a VS12 sub. I can’t seems to make it work. The mixer came with two speakers that is hooked with 1/4 cable. Please let me know if you can help me. Thanks.

[@expertisland]

🌴Good News I have a video on that here is the link👍 kzbin.info/www/bejne/ambVnXudhZdlopYsi=iv7lTqGXW4qehcYs&t=367

[@ReccoRowson-le4zo]

Hi I would like to know what subs would go well with my EV ELX115 pa speakers they are not powered speakers and I have the Crown XLI2500 to power the speakers and I need a good mixer

[@metzger723]

Hello, I have the Harbinger M120 PA system (purchased circa 2016-2017 but still works really well). I’m thinking of buying the Harbinger S12 sub to pair with this system. Do you know how I’d connect the sub to the amplifier for the PA system? Also, is there a way to divert some of the bass frequency from the PA speakers to the subwoofer?

[@Peregrine101]

The video shows one answer which will work in general for the first question. The difference would not to use XLR cables, because the outputs on the mixer use a different cable. The subwoofer is able to use those on the input side. The tricky part is the connection from the subwoofer to the speakers. You need a special cable for that, as the speakers lack XLR connections, too. But those are available. Your second question is not addressed very extensively in the video, but the answer there is the crossover dial on the subwoofer. This dial sets exactly what you are asking for. It works out the exact point where the subwoofer hands over ("crosses over") to the speakers. What the best setting for your liking is, you have to determine by experimenting for yourself.

[@venomdrinker7277]

I have 2 Alto TS415s and a alto TS318 sub how do i connect that? I also have a mackie profx 12 mixer

[@georgeortiz5941]

Hello my name is George Im using JBL speakers but don't have a mixer to connect to...can I connect my speakers from the subwoofer to the tops and how to do so.....

[@djql1958]

What is the setting on the subwoofer and the speaker you didn't say but I understand the connection i just don't know what you set the top speaker too and subwoofer

[@user-jz9of8cl4j]

Hi. I would like to know how can I plug a voicetone H1 TC HELICON (pedal for voices) to a Harbinger mixer ?

[@omaipeter]

Can I use only one subwoofer connected to 2 speakers? or Should it be 1 subwoofer to each speaker?

[@michaelreed5173]

I'm coming from my controllers ddjsz2 to external mixer, my main out of controller left and right to line left and right on external mixer, can I run top speakers left and right speakers to main on external mixer and run subwoofer on central room on external mixer to separate top speakers from subwoofer can that be done?

[@PunkRockConservative]

I have the harbinger M100-BT PA and the S12 Subwoofer with no pass through when the sub is connected, any ideas ?

[@fausto412]

I just acquired 2 EV XLZ 12 BT speakers for the house. I'm wanting to get a sub but unsure about just how much sub I need to give me good solid clean bass and can 1 single sub do the job for both PA speakers or do I need to acquire 2 smaller subs? which is more economical and which is more bang for your buck? I may get a mixer too but then doing that means I need a controller and laptop and I'm not ready to spend so much money right now. Just trying to get a banging system for my pleasure and the occasional house party.

[@mohev]

Hi I have one Mackie reach, can you advise me on what sub that I would need please Mo U.K

[@brandonbrenton1680]

I read that you can’t used a powered mixer with powered speakers is that true?

[@SUPAROCKINDJSMASH]

TRY THIS SAME THING BUT SHOW HOW TO ADD A DBX DRIVERACK PA WITH MIXER & POWER SPEAKERS

[@expertisland]

DBX DRIVERACK is a Cool piece of Hardware with the App controlling the Cross-over And EQ. One Day maybe.... one Day.

[@justingarret4776]

@@expertisland If I'm using a dbx gorack where in the audio chain should this be. I've been going from my controller xlr to the dbx gorack to the sub and then out to the mains. I set the gorack volume at max and just use my controller to control volume. Recently had someone tell me I should be going 3.5mm jack from laptop to gorack and then into the controller and out to the sub and use the gorack to control the volume. Thank you!

[@isaacw9240]

How would you hook up 2 subs & 2 top speakers?

[@elbertobenza449]

Good day! Is it possible to set up 4 alto tops and 4 alto subs on a mixer only? If not, what additional accessories will this set up work? Thanks.

[@noobm8888]

Hey, My father recently got 2 Subwoofers and 2 Speakers just like from the Video except I've been having trouble with connecting 2 speakers and 2 Subwoofers to Mixer. I also seemed to have trouble on how to setup the Subwoofer to make sound. It's my first time with these Subwoofers (The Microphone hasn't arrive yet so, I'll just try to test it when it arrives)

[@ricklitton]

Nobody ever gets an answer

[@chanxiong7421]

You can connect the main output (L) on your mixer to your (L) subwoofer input then connect the output on that subwoofer to your (L) your speaker input line. Do the same for the subwoofer and speaker side (R).

[@shaunsmith6150]

What would you recommend 4 me to hook up ekx 18 subwoofers to my yamaha 12u mixer

[@braxtonferrell7982]

Okay so I need help I have the speaker and I have the 12 in sub I have one cable but I’ve plugged it in so many different ways and it won’t play bass I’m completely lost

[@amitkapoor6845]

How to connect 2 (Two) Bose S1 pro (L & R Stereo) to 1 (One) Bose Sub1 through Yamaha MG10 XU

[@djromeograte8180]

I posted a video test for the S12s. Are you guys going to post a test of the S12s as well? I would love to see that!!!

[@expertisland]

Hope this week for a video, and I just watched your video on the S12 good talk on the Sub.

[@josephfranco1495]

So I have two 18" VS18 vari of the latest harbinger's 18 inch subwoofers, and two 4115 speakers. How do I connect them together?

[@elsiellamas8000]

How do I hook up my custom PA to a secondary floor unit to be used as a sub. If this cannot be used as a sub what do you recommend another custom PA?

[@leethatsme1988]

Hoping someone could share some advice. I have 2x PA speakers with 15inch drivers. There is no model or any numbers on the cabinets but the drivers are 15inch eminence drivers. I have an old kenwood amp that as an output rating of 8-16 ohm. I think the drivers are 4ohm i will have to test them with a multi metre when i can but my main question. My amp says " lower impedance capability" on the front. Would that mean i could use the amp on these PA speakers.

[@mikeplaysjazz3487]

Nice video! It helped a lot. Question. Which setting should I put the output crossover in?

[@tnkpro4sho]

Good rule of thumb is between 100 and 120

[@bullskull1166]

I have a BEHRINGER Xenyx x2222usb... I have two 15in powered speakers running out of the MAIN OUTPUTS L and R of the mixer... Then I have one 15in powered SUB running out the SUB OUTPUTS 1 and 2, I have each cable running out of the mixer to both the sub INPUTS on the sub... Is this ok? I wanted to do it like this so I can control the sub separately... Im just not sure if I have it correct...

[@iexecutionzi8400]

Any mixer would work that has the appropriate plug in ports?

[@mvcnow]

Can I use my Simmons drum amps as a p.a? How would that set up work?

[@DJ_Unique_UK]

I’ve got 2 ts412 tops and I use ts215s 1250watts, sound on the set up doesn’t sound great and I can’t find anyone who’s done a video on this set up please give us content on this I’m not sure if it’s compatibility or there’s something I’m doing wrong

[@aaronjademusic5197]

What does LPF stand for on my powered subwoofer? It starts at 40hz to 180hz and so how do I adjust that frequency? Thanks

[@expertisland]

The Low Pass Filter (LPF) is a crossover filter network that allows frequencies below the set-point to pass onto the subwoofer driver Lower the tighter the sound.

[@MrSollex1]

Where do you plug in the second Subwoofer then ??? You plugged both right and left out from the mixer to just 1 sub. I don’t understand… why both to the same sub ?? Isn’t Left to the left sub and Right to the right Sub ??

[@expertisland]

If you have 2 subwoofers you are right ✅️ is the easiest way to get the job done.

[@whattodo8593]

Basically he's using the subwoofer's crossover to effectively route the selected range of freq to the loudspeakers

[@Yellowjacket1977]

I believe this example is if you only have one sub as I do. I'm only running one sub. I assume if you own 2 subs, you would come out of each sub to a top speaker.

[@SuAmigoElilegal]

​@@Yellowjacket1977 hello I do also have one sub so I use this setting but I have a question I have 2 more power speakers , how do I connect those 2 extra ones. Do I use the top load speakers outputs left and right for each side 🤔 and by doing this is it putting overwork on the subwoofer sence is just one and 4 power speaker sor is it okay

[@Yellowjacket1977]

@@SuAmigoElilegal Good question. To be clear, your coming from the mixer, to your one powered sub, then out of the sub to a pair top FOH powered speakers, then out of that L-R pair into another pair of powered speakers? I'm not the expert, but it doesn't seem that the powered sub will be overworked since it's pulling the frequencies it needs, and sending the other frequencies to the 4 FOH top speakers. I'm very new to powered speakers having just bought my first pair last week. (I bought a pair of Yamaha DZR12 2000W 12 inch Powered Speakers), so I'm coming out of my 18" JBL Powered sub into these new Yamaha's and experimenting with different settings.

[@SuAmigoElilegal]

Hello can I also connect an extra power subwoffer trough the monitor input and then from the output of the sub to the other floor monitors

[@Cowboyninja70]

How do you control the sub from your mixer. I have the same speakers your showing. Hooked it up just like you?

[@shalva098]

In case of two sub and two tops, how can i set a proper connection?

[@joshaaron80]

I’d like to buy a s12 sub. Can I hook it up to the m200bt? Thanks

[@naarendranarain2890]

How would you wire up if only using Bluetooth?

[@aliboy123]

What mode are the tops set at? Club, Standard, Slave ?

[@jttruong2681]

Live for sure

[@omaipeter]

Do you always need to have a subwoofer connected to mixer then from subwoofer to speaker? Is it OK to connect mixer to speaker directly without subwoofer?

[@djmorry8748]

You probably have got the answer already but just in case - yes of course you can connect without a sub woofer just connecting speaker's to left and right main outs on your amp or mixer!

[@ppiercejr]

What would I do in this setup if I need to add 2 more speakers that need to be delayed for a much larger audience space?

[@sami011212]

Easy just hook the new speaker to the output of the previous one, to the input of the 2 new speakers you just add. So again plug your cables in the speakers the one hooked to the subwoofer on the outputs and plug the other end to the cables on the inputs of the new speakers you just add.

[@ppiercejr]

@@sami011212 that won't solve my problem of delaying the speakers, which I solved by using a DriveRack VENU360. Certainly more of a pain and more expensive, but that is sometimes the way to solve the issue

[@sami011212]

Oh sorry I was thinking that the speakers are close to each other, because I do that in all my events, but in my case there is only 12 foot between the two speakers.

[@eliasjabbour5781]

Hey guys I have questions for you can I connect 2Mls. 1000 , 2 pa v4115 2500w and 18 inches sub harbinger to lv 14 channels mixer Thanks again

[@miroslav8817]

Thanks for video man! Please tell me is the one cable from the sub to mixer enough if you want to connect just one top from the sub , using one main output. I try that and it looks it is just fine. Or i have to connect sub with both mains from the mixer , like u did?

[@georgeogrady449]

There are left channel and right channel which one you go for different speaker

[@djaga4404]

Would a ddj go from master to xlr input 3 and 4?

[@BrainInSkull]

Thanks for the info. Is there a way to use this subwoofer with the Harbinger m200 PA? The speakers are passive but the mixer is powered. Cheers.

[@expertisland]

Yes You Can Use the 3.5 stereo output connection here is the link to the Cable you will need guitar-center.pxf.io/DVNXA2 Livewire Elite Interconnect Y-Cable 3.5 mm TRS Male to 1/4" TS Male. Good News We Will be having a video on the M200 coming up in the next few weeks.

[@user-ch7nx4yx7x]

Sir indeed to connect 2 subwoofer with splitter

[@expertisland]

Subwoofer link together

[@pampolletta5673]

If I'm correct thru does not work Bluetooth for a powered sub how do I hook up jbl irx112 to a sub no mixer sorry for ignorance new at this any help from anyone appreciate it thanks

[@rolandjuliuselvis]

I watched this video hoping to resolve my question about connecting mp powered P.A. system to a power subwoofer and I was disappointed. I thought that he would explain how to hook a p a system to a powered subwoofer?? Again, hooking up a p.a. system to a powered subwoofer.... I can't seem to get any right information on this ??

[@loverlyvalera626]

Can i use one subwoofer for my pa 2speaker sound system?

[@expertisland]

Lots of people do that, but you have to look at the type of music playing and the size of the space you're playing in.

[@ralphgeronilla]

Does it matter if your xlr to 1/4 is balanced or unbalanced?

[@josephkim6892]

Where do u plug the power amp into?

[@Tony-ds2nm]

Hi, can xlr cable for microphone be used to connect between subwoofer and full range speaker? Or is there any specific cable to connect between the speakers? Thankyou

[@GrimYak]

Same

[@RukeRadams]

Does this way still run stereo?

[@mikewood9514]

hi. i have a question. if i have 2 active p.a systems ( bass and tops). can i do the same thing but use one for left and one for right?

[@expertisland]

If you do that you Need to run everything in Mono. or Mixed Stereo.

[@mikewood9514]

@@expertisland thanks so much for that info.