thanks for that one, i notice you have nice clean tidy work shop..unlike mine..
@82McKinley7 жыл бұрын
Has anyone ever tried this method on a conversion varnish, ie post-catalyzed varnish?
@femfic25517 жыл бұрын
could you do this on a floor? i just re-finished my floors and there are some "dust nibs" and a few kitty hairs that unfortunately found their way onto my floor before the finish dried
@williambranham62495 жыл бұрын
I love our cat. Kitty hairs in a finish could be the start of carpeting.
@danieldavis560617 күн бұрын
Like magic!!!! Worked great!!!! Rubbed a satin polyurethane with this method...removed every single defect, it also removed the streaks that were driving me nuts. Thank you!!!!😊
@mikewest7128 жыл бұрын
gotta change that name
@sammathis2 жыл бұрын
This is the simplest explanation of this process that I have seen yet, thank you for sharing.
@cabinetguy308 жыл бұрын
what's the soap to water ratio and what kind of soap ?
@atcjmas3 жыл бұрын
I would think just enough to make suds. A drop or two per 8 ounces
@scootertheturtle3842 Жыл бұрын
He says “4zero steel wool”, but I believe he means it as “#0000 steel wool”. Be careful people as other types of the wool than 0000 will be too abrasive
@phi924911 жыл бұрын
Thanks. Rubbing out poly can be tricky especially with thin coats. Lacquer is much easier to rub out but I do not have that luxury with the current piece.
@kyler60865 жыл бұрын
Can you lower the sheen with this process too? IE take a satin sheen poly down to a more matte finish? I'm almost to this point on the table i'm building, and i'm trying to get a duller sheen than what was available with the oil based poly.
@Dan-vo7vc3 жыл бұрын
Lemme know if you found a good answer to this question!
@AmericanWoodworker11 жыл бұрын
In the story and this video we use dish soap.
@331LX7 жыл бұрын
Can this method be used on the oil based minwax polyurethane finish?
@kyler60865 жыл бұрын
Yes it can, but you'll need more coats with oil based polyurethane, as it puts down lighter coats than the typical water based. I don't even sand between coats until I have at least 3 coats down first.
@thedodsons383 жыл бұрын
So will this rub out brush marks on water based poly? I’m struggling lol
@briarfox6377 жыл бұрын
This is a good technique. I use it a bunch with my shellac finishes.
@bgm19115 жыл бұрын
Half way into the video....thank you for explaining why you are doing the steps. Too many videos just show a process, never an explanation, which does nothing to help understand and learn the process.
@jameskrys528610 жыл бұрын
I was going to try this on a maple guitar neck i just finished with Minwax clear poly. I did the first stop with the 4-0 steel wool. For the second step, I had a damp sponge and a bar of Lava soap and a light bulb went off above my head. I rubbed out the neck with the Lava soap, then automotive polish/scratch remover and it came out shiny and orange peel free.
@mitmaks11 жыл бұрын
can you do this with gloss polyurethane?
@SarcastSempervirens3 жыл бұрын
just use higher and higher grades of wet sandpaper, like up to 5000 grit and then finish it off with paste wax, buff it and there you go
@robinjoly92629 күн бұрын
This may have already been asked. I used a Varathane brand oil based satin spar-urethane on a table top. How long would I have to wait before using this process? Is 24 hours long enough?
@StormLaker2 жыл бұрын
I'd be afraid to use 400grit- maybe 600-1000 grit would be better to prevent over sanding?
@whitey07079 жыл бұрын
I'm a novice, and am working on an oak coffee table now. I notice that you mentioned in a reply about a year ago about low spots - here it is {Any low spots (like pores in oak or minor indentations) will show as little shiny spots}. I have been watching many videos, and I really enjoyed yours and found it quite helpful. My question is how to get rid of the low spots? I have put multiple (3) coats on, and it seems that they just keep reappearing. Quite frustrating. Sorry if this is a basic question; as I said I am a novice.
@whitey07079 жыл бұрын
Connor H Thank you! I appreciate that link; it was helpful.
@williambranham62495 жыл бұрын
Yes Conner is right. You need a perfectly flat surface in order to have an even sheen. You have to sand forever when preparing the wood and or or fill any pores or small low spots before putting your finish on.
@kerryschoolfield15374 жыл бұрын
I have a question. Should this method be used on an oil based varnish? Or should the water be substituted with mineral spirits?etc.
@sl90542 жыл бұрын
Best video ever, I tried this method and it honestly gave me the best finish I've ever done....silky smooth thank you!
@saiyedmurtaza46036 жыл бұрын
My finish is always very soft and doesnt really harden so soft that i can make a deep scratch without putting any pressure with my nail I let it cure and have tried the best brands we can get here which makes me think there is somethink wrong with my application process what could it be
@williambranham62495 жыл бұрын
How long do you let it cure,? Check the manuf. date of the product. It may be possible that it could be old. I'm not sure if age can affect the cure time.
@RealRuler211211 жыл бұрын
Good video and really makes it seem simple. This may be a silly question, but what kind of soap is appropriate for this purpose? Dish soap, hand soap, laundry soap, soft soap, dissolved bar soap... Or am I overthinking it and it really doesn't matter as long as it's lubricative rather than abrasive (such as Lava soap)?
@gregl22492 жыл бұрын
STILL NO ANSWER??? HAHA
@phantomcreamer5 жыл бұрын
I never use soap and water with steel wool. Steel wool breaks down as it is rubbed and small pieces can become logged into the finish and wood. If it is soaked in water, it oxidizes leaving spots of rust in the work. You can get away with it if it is the last coat, but you will have quite a flat matte finish because 0000 isn't even a very high sheen to finish with.
@MyREDTAIL5 жыл бұрын
Question.? W hat Color & Brand of Stain is that Board, That your working on.? Thanks for sharing etc.
@JLP22245 жыл бұрын
MyREDTAIL it’s quartersawn mahogany......
@Chels_EfraenАй бұрын
Finally a videa that explains this
@telosfd11 жыл бұрын
Can i spray it with lacquer for better polishing after this?
@chuckd24837 жыл бұрын
You should remove the dust after every sanding.
@donmac181110 жыл бұрын
This is good when you need to rub one out.
@zedudli2 ай бұрын
ACE video!! My finish on an antique box restoration project was all bumpy and grimy feeling, with this method it came out all fancy and professional looking. Thank you for the precious advice!
@johnnyrodriguez59383 ай бұрын
Will this work if my top is painted. I used chalk paint and then I finished it with oil based satin Poly.
@johnnyrodriguez59383 ай бұрын
It’s a ping pong table so I added the poly for durability
@melaniemel27326 жыл бұрын
Great video right to the point thank you
@almfoto8 жыл бұрын
This is by far the simplest and easiest method I've seen! I will test this out on some sample pieces, thanks for the easy to follow video.
@jrmjrmeeker10 жыл бұрын
how well does this work on red oak wood or does it matter about what kind of wood
@newinspiration21088 жыл бұрын
+Jimmy Meeker this method works for any wood and or finish but not safe as 400 is a bit too aggressive for last coat and it's not easy to use 400 grit to remove surface imperfections. I'd go with 1200, yes time needed is more but the job would be much easier and relaxing
@HomeImprovementWoodworking7 жыл бұрын
I prefer to use mineral oil as a lubricant
@NosillaWilla9 жыл бұрын
if you guys want to up the sheen to a gloss i'd follow up the 0000 steel wool with 0000 pumice and then rotten stone. i like to use soapy water and a linen cloth with a wooden block to apply pressure and buff away. clean it off with more soap and water.
@SD-yb5fx5 жыл бұрын
Can your process to be used on white water-based lacquer? Preferably Kem Aqua Plus by Sherwin Williams.
@southernguy354 жыл бұрын
The only thing I have to add is not wearing gloves while doing this. Everytime I've used steel wool without gloves, I've gotten minute splinters in my fingers. This isn't as extreme as trying to pull off finish and you have it wet down, but i would think one wouldn't want to breath that steel wool dust in, if there is any.
@elvenking62 Жыл бұрын
When I do that last step I do it with 4O steel wool and Howard’s orange oil and wax. Smooths without scratching and puts a beautiful shine on finish
@909sickle5 жыл бұрын
Chicken choking humor aside, why is it called "rubbing out"? It appears to be just regular sanding.
@gregl22492 жыл бұрын
Personally I wouldn’t use the circular motion and I would also apply 1 final coat without doing anything afterward if you want a gloss finish
@kevinlantaff63077 жыл бұрын
If am shooting for a satin sheen with lacquer on seven pieces of furniture I am building that have lots of raised trim areas. If I feel that I want to bring back just a little gloss to the sheen, would you recommend paste wax with 0000 steel wool, or something else? Also, I will be spraying. How many coats do you recommend so that I stay clear of the wood when rubbing out?
@rsngrl8 жыл бұрын
so yes or no, this will work for a satin surface?
@femfic25517 жыл бұрын
dumb question
@dmvhon Жыл бұрын
I'm assuming the finish is poly. Will this work also with laquer?
@lesd26332 жыл бұрын
2:10. You reached to you apron and said “I didn’t do that”. What were you referring to?
@Ladioz Жыл бұрын
Not even gloves? your hands are gonna end up sticky for hours
@rkgsd7 жыл бұрын
Can this process be used to knock down the shine from oil based stain? Seems a light steel wool would do it.
@spiromandylor Жыл бұрын
IIs this done in between coats or ONLY on the final coat?
@Dan-vo7vc3 жыл бұрын
Any tips for a process that would reduce the gloss a bit?
@edwardheyrich86012 жыл бұрын
Where do you get a felt block like the one you used
@mikekadar6369 Жыл бұрын
Do you need to add a wax or anything after?
@korgbass5 жыл бұрын
Can you use the same technique with a solvet based alkyd resins varnish?
@danalaniz73143 жыл бұрын
Thank you. This is really clear and informative.
@Paperstringz3 жыл бұрын
This is a lacquer finish, right?
@ssn70810 жыл бұрын
Don't you have to let the finish cure for 1-2 weeks before you do this? I had thought that.
@williambranham62495 жыл бұрын
That is best, yes
@ironwill47066 жыл бұрын
Nicely done so after that, is the project finished ?or would you put one more finish coat
@RM-en9gk7 жыл бұрын
For this technique to work, does the wood grain has to be filled or it also works on open grain?
@danniellecarver89827 жыл бұрын
Does this also work for Polyurethane?
@rxonmymind83627 жыл бұрын
Dannielle Carver Yes
@ilyalioubarski99677 жыл бұрын
Rxonmymind how about oil poly? Do i use soap and water or mineral spirits?
@rxonmymind83627 жыл бұрын
Ilya Lioubarski I don't want to misinform you so call your hardwood supply store. Not home Depot but an actual cabinet store. I ONLY worked on extremely faded walnut using a variation of this video. Good luck!
@AmericanWoodworker11 жыл бұрын
While this method would theoretically have the same effect on satin or gloss, complications are likely to arise when lowering the sheen on a gloss surface. Any low spots (like pores in oak or minor indentations) will show as little shiny spots.
@simonlaura4 жыл бұрын
I have refinished our dinning room table, I have 7 coats of poly on right now. I tried this method and it made it look dull and sanded, even when I used soapy water. I even tried a 1000 grit hoping that would help but still had the dull look. All I want to do it remove those fine dust particles and what not. Lol
@torinsosich15342 жыл бұрын
@@simonlaura then polish it with car polish afterward... or a 8000 grit 3m trizact pad
@bgm19115 жыл бұрын
Some more details about the entire process would be helpful, specifically, why did you start with sandpaper and then go to steel wool?
@nwsmith94 жыл бұрын
Rubbing out a finish is essentially scratching it with finer and finer scratches. The sandpaper is more coarse than the steel wool which is why he started there.
@grindstone49106 жыл бұрын
That fucking title tho
@Chris-pj1os4 жыл бұрын
What clear product?
@tedschaar93644 жыл бұрын
Used this method on a quarter-sawn oak tabletop I'm making and it worked great. Wow! Went from a surface bumpy with "nibs" to one that is smooth. Very impressed. Many thanks from America's Dairyland.
@shericarnevale802011 жыл бұрын
can you rub out stain that has been applied to thickly
@jaden201010010 жыл бұрын
Can I use this to smooth out painted furniture that has a semi gloss paint on?
@jrmjrmeeker10 жыл бұрын
can you do this on a high gloss finish. with all the steps you just done and my wood is red oak
@phantomcreamer5 жыл бұрын
You can, if you don't want it to be a high gloss finish
@mrsblackirish75 жыл бұрын
Would this work for polyurethane?
@danielwinsor60185 жыл бұрын
It does, but it's recommended to wait until the poly is fully cured, which can be as long as a full month.
@tech4life3658 ай бұрын
DO NOT GO IN A CIRCULAR MOTION IT WILL CAUSE SCRATCHES
@EliUrGuy5 ай бұрын
The soapy water doesn’t help hide them like he said? Genuine question
@tech4life3654 ай бұрын
@@EliUrGuy nope
@tech4life3654 ай бұрын
@@EliUrGuy go with the grain and you will be fine
@djmcommish127 жыл бұрын
Great video. Thanks!
@walterrider96005 жыл бұрын
thank you
@jrmjrmeeker10 жыл бұрын
what type of wood is that top that you are working on love it
@frankl.439710 жыл бұрын
that is african mahogany.
@fireworxz2 жыл бұрын
Thanks
@gaylonlee7 жыл бұрын
Ń
@ccccen7 жыл бұрын
hi
@robertnydza1234567898 жыл бұрын
Does this also work on poly finish?
@alecgrace64687 жыл бұрын
Robert Nydza yes
@ccccen7 жыл бұрын
nice
@ryanyoung20967 жыл бұрын
ah, so the key to a fast finish rub-out is lubrication?
@rongutzwiller97645 жыл бұрын
Ryan Young I see what you did there.
@sirbondman0078 жыл бұрын
Thanks for the tips!
@sebastianr918 жыл бұрын
thank you :)
@jeffcole95107 жыл бұрын
'
@bencollins516 жыл бұрын
Brautiful
@PZERGYO12 жыл бұрын
EXCELENTE VIDEO, GRACIAS
@jrmjrmeeker10 жыл бұрын
love the striping in that wood what is it
@RoboCNCnl10 жыл бұрын
I'm pretty sure it's sapele mahogany...
@robira13138 жыл бұрын
He said it's African Mahogany.
@RoboCNCnl8 жыл бұрын
That's why I'm sure it's Sapeli, It has those tripes, and is mahogany from Africa. (I work with this wood almost daily)
@benjaminlambert894410 жыл бұрын
Great video. We use a similar technique using Murphy's Oil Soap. I love how you used the felt pad, where in the world do you purchase those? Cheers!
@akyak3337 жыл бұрын
you could use a blackboard felt eraser
@williambranham62495 жыл бұрын
Any woodworking supply, Woodcraft and probably Amazon
@josephefasciani73435 жыл бұрын
@@akyak333 That's what I was thinking!
@justmydeals7 жыл бұрын
I used 0000 steel wool with soapy water and it left tiny scratches in the finish.
@williambranham62495 жыл бұрын
Perhaps, too much pressure or a lesser quality steel wool.
@Mark-bn7lk3 жыл бұрын
No
@micahhowell443210 жыл бұрын
What type of finish did you use?
@MYGOLDCOIN1019 жыл бұрын
He used a varnish finish. I didn't know varnish could be rubbed-out to a satin finish. looks like a good job. I am rubbing out a laquer finish today on some wood working tools I made, with minwax finishing wax paste.
@janwynsen96226 жыл бұрын
Best and most instructive video i've come across. Thanks!
@IsaacOLEG7 жыл бұрын
Luberon is lucky to have American customers it is considered as only DIY products, no professional would use that brand . the products are probably more easy to find but their quality (solid content, dilution, uv filter,) is not what we need for long lasting professional furniture repair or building. regards their steel wool is certainly normal that said ;)
@williambranham62495 жыл бұрын
LIBERON
@imy2618 жыл бұрын
You make it look so simple
@Vesterpester8 жыл бұрын
Would some automotive polishing compound give you a high gloss finish after these steps?
@ovais9097 жыл бұрын
Yup it would make it too glossy
@willy00795 жыл бұрын
of course once again there is ABSOLUTELY no way to see the finished product because hes not showing it The sanding marks are not "invisible to the naked eye" your figure 8 swirls with the steel wool show up big time , and if you aren't comfortable showing us the final product we can assume it didn't turn out well at all
@masonhamlin82395 жыл бұрын
Agree. I keep seeing these guys doing a final rub out in a circle pattern. If you want to look good when you actually look at it, you have to rub in straight lines. These guys make me think they really don’t know what there are doing.