First Ride on 52V Razor E325 Hub Motor Converted E300 Electric Scooter

[@MooseRidez]

Was waiting for this!!

[@drewski6843]

Ahhhh man! Just the video I've been looking for. Just got an old bladez xtr with two lead batteries, small chain driven electric motor. How's your scooter doing? Anymore upgrades? Did you like the speed or did you modify it to go even faster? Thanks for the vids.. Instead of the 500w motor that size, is there a stronger hub motor to allow me speed? Again. Thanks for the vids.

[@PatOutdoors]

This scooter is sketchy going faster than 25 MPH to be honest, just because of the lack of suspension. I also made the mistake of doing a twist grip rather than a thumb throttle so I’m making some changes to this set up. Frame size is the limitation for putting in larger hub motors, but I mainly chose these since they are less than $90/wheel/tire. I purchased a second same hub motor and controller so I can run AWD set up. Will post about the build more soon, just too many projects right now!

[@drewski6843]

@@PatOutdoors are you going to add forks with suspension? Ya, I think my tires are the same size as yours. It would easily fit my scooter. I was also thinking of getting a seat kit that has a suspension poll. The rear-end is rigid. But I think having forks with suspension and the seat having suspension should be good enough? Want to see how your dual motor scooter build will perform. Like I said, I got this bladez xtr scooter and it's all original. Lead batteries, small chain driven electric motor. As for the throttle, it's a squeeze throttle (like a brake lever). I think I'll just keep that setup. Looking forward to your upgrades man.

[@bach2458]

I'm wanting to change out my vevor controller on my 48v mx650 for a Kelly controller. Then possibly buy a second battery and run a dual 48v 30ah system at 100a. Super excited to see what the future has in store for your scoot! Keep up the great work as always!

[@PatOutdoors]

That would be a serious initial burst of torque at a twist of the throttle.. do it already!

[@Timboslicce]

Very nice build. I think I’m inspired

[@dr.projectx5142]

Add slime in the tubes to prevent a flat. It helps a lot.

[@PatOutdoors]

I'll try it out!

[@DescartesRenegade]

Damn, I have been looking at e300 builds. Nevermind now. Need suspension.

[@PatOutdoors]

It has its downsides unfortunately. I’m still converting this one to dual. It or though. I just don’t suggest going 30 mph on a non suspension scooter

[@kgeo4764]

can you show us a picture of the welded caliper? I'm curious of how much space is needed.

[@israelsantos6473]

Would like to know if there's an update to this project. Nice touch using the space from the old motor for all the wiring.

[@PatOutdoors]

There certainly can be an update on this project, as soon as I’m done with my current razor go kart build I’m redoing this one. Already have a second hub motor for the front and planning out how I’m gonna add suspension to it. Just stay tuned!

[@davidlongM54E46]

Super excited with this one!!! Love my E 3 hundy, but no suspension is rough!! Right now getting 22 on 36v with 800w controller. Plan on going hub very very soon. Just did my first hub build on a 26" walmart MTB and fell in love with the smoothness and lack of noise.

[@bdrgarage7039]

I would just run 60v at it. I have a brushed currie 24v 500w on a big tire E300, runs 23mph flat out, 26-27 down hill. Has a Fast scooters 36v 1000w controller and lithium battery.

[@mryokai92]

what was the top speed for this build ?

[@rod8652]

so i just got my mx350 working, battery hooked up, motor mounted etc. i have the same throttle but it’s super sensitive and it is just a torque machine. do u know any sprockets that give less torque? it would be helpful

[@PatOutdoors]

If you go larger front sprocket, it slightly reduces torque, but increases top speed even more.. I never did an MY1020 kit for my MX350 when I had one because the wheelbase is so short that it would lift the front end too easily. What you really want is to upgrade the Controller to a Kelly KVD so the throttle input is more modular (controllable.)

[@rod8652]

@@PatOutdoorsi’ve been experiencing that wheelbase so that’s why i am extending the rear frame. if u can, may you recommend me some sprockets? thanks

[@buythebarcreations.]

How much for a commissioned custom piece?

[@PatOutdoors]

What do you mean commissioned?

[@buythebarcreations.]

I have a few people who are willing to pay for a completed build that they can then customize after the initial set up of the bike you build I have donor bikes if need be and I’d get the parts needed to get the first bike done by you for the example bike build

[@PatOutdoors]

Are you in the east coast? I'm in northern VA.@@buythebarcreations.

[@buythebarcreations.]

Yep I’m in Baltimore and fl I have residency in both places I’m more closer to va more often right now tho so that would be perfect

[@PatOutdoors]

Y'all want MX650's and MX500's built or Stand up scooters? DM me on IG @pkasilag@@buythebarcreations.

[@Timboslicce]

Poor guy, that 300SM is a turd lol.

[@PatOutdoors]

What’s wrong with them?

[@Timboslicce]

@@PatOutdoors nothing, great bike just underpowered compared to the price. In my opinion. I have rode that bike about 50 miles. Compared to even a Yamaha 250SM it is underpowered. That goes for the Honda 300 as well. The Yamaha 250SM is actually faster for the money. When I say faster, I mean not get run the hell over on the freeway at 65mph lol.

[@simmack17]

You should get a seat

[@PatOutdoors]

Hmm I’ll consider iy