Actually... this seems like a really good idea. Mint. I think I might run this setup on my single turbo.
@drbiz4954 жыл бұрын
3:22 I love this....
@jjjjjj92842 жыл бұрын
On my ls1 turbo i run my drain into the timing cover , which is right near the pickup so that's why i have mine draining into there
@infinite7z13b5 жыл бұрын
I dont know any other way to sharpen tungsten.. lol carry on!
@DOCTRJ3 жыл бұрын
Nice job
@jasperpipes42223 жыл бұрын
Y'all know that recess drilled out is to allow clearance for oil pump bolts right ? Definitely not an optimum spot ! Oil pan return above oil height in line with a main cap is correct method.
@Seasidebullies4 жыл бұрын
This is also the way I did it but now I got to figure out what fitting will clear the crank pulley, what did you use?
@randyrasmussen80313 жыл бұрын
Weld it at a 45/
@tikkyturbskistearl77462 жыл бұрын
What fittings are used to avoid balancer
@alejandrojimenez62604 жыл бұрын
I did this for single turbo setup, but the an 90 fitting I have hits the balancer. What fitting did you use?
@Seasidebullies4 жыл бұрын
Me to and don't know what im.goi g to use
@MrJakefisk4 жыл бұрын
you dont have to pre heat ?
@ChrisTheMobileMechanic5 жыл бұрын
No link in description
@BrandonBurns19855 жыл бұрын
Thank you missed that Here ya go. More progress later this summer. kzbin.info/www/bejne/ZqPOlGaNqLBmma8
@antoniogarcia-qe7dz5 жыл бұрын
For twin turbo set up do you think it’s fine to drain both lines into one single line connected by a T fitting and into oil pan instead of drilling two holes since I already have one made and don’t want to take off oil pan again
@BrandonBurns19855 жыл бұрын
Yea should be fine as long as the hoses are sloped downward and the hoses are large.
@antoniogarcia-qe7dz5 жыл бұрын
Thanks for answering was thinking of using 1/2 in hose like I did on the first line I had hope that’s big enough
@randystingray65444 жыл бұрын
If your turbos are high could I drain into the valve covers possibly??
@BrandonBurns19854 жыл бұрын
@@randystingray6544 yep! I've seen that done too.
@antoniogarcia-qe7dz4 жыл бұрын
Fix or Fab yep works as well for my twin turbo set up I did a t fitting and been working great no problems at all should be the same dumping into valve covers
@DAG.Garage3 жыл бұрын
What size fitting are those?
@BrandonBurns19853 жыл бұрын
10 an
@jnarvaez896 жыл бұрын
Is there a problem if the drain is lower than the oil level in pan?
@BrandonBurns19856 жыл бұрын
This is not below the oil level. But I have seen where people will drain it into the oil plug... I would imagine that would be ok due to pressure equalization. Haven’t tried it tho.
@amperformance15 жыл бұрын
It’s supposed to be higher than the level
@Brian-ws1si3 жыл бұрын
@@BrandonBurns1985 what fitting you used to clear the balancer?