Fixing Creality Ender 3 V3 SE Hot End JAM

Fixing Creality Ender 3 V3 SE Hot End JAM - Disassembly & Unclog

Рет қаралды 10,883

Күн бұрын

Пікірлер: 46

@skelobones Ай бұрын

I love how even when you found the hardened filament, you didn’t stop there and you showed other possible problematic pieces for others to see what to do (like the direct drive gears)

@The-Master-Chief 3 ай бұрын

Thank you so so much! My ender 3 se v3 had a very bad case of it clogging after I ran out of filiment and it got stuck there. I tried everything and looked everywhere for tutorials. I couldn’t find a single one.. Until I found this one which is the best tutorial I have ever seen, it’s at perfect pace, goes over every detail and everything you should watch out for. Tells you what to do incase certain stuff were to happen or if you need a slightly different solution. You have all my thanks.

@KakiDIY 2 ай бұрын

Glad it helped! Thank You very much for the kind comment and feedback.

@The-Master-Chief 2 ай бұрын

@@KakiDIY No problem, it helped alot although very unfortunately my printer broke again lol. It was leaking this black, glassy like substance that was plastic like in texture that was so hot it melted through the print bed. Sorry to ask but do you have a video on leaky filaments or that anyone else has one? Just wondering but thanks a lot for the tutorial as I helped me finish my build.

@thebathbakery 4 ай бұрын

Thankyou this totally worked - was a bit nervous unscrewing all those screws lol - and praying you reversed it at the end so I could put it all back together again - but got the clog out and now its working perfect again.. It has given me the courage to now try on my 2 x flashforge ones lol

@KakiDIY 4 ай бұрын

Great work! And yeah, way too many screws to our liking. But it is doing it's job to make the printer look nice.

@arugondraos2133 11 күн бұрын

Thank you, you helped me a lot with this video, I didn't know what to do to unclog the pipe

@voongnz 3 ай бұрын

excellent instructions, i haven't had a clog yet since 8 months of ownership but this is a great resource to have on hand should the problem eventually arise. thanks.

@KakiDIY 3 ай бұрын

Thank You for your comments. You must have given lots of care and attention to the printer and feeding it good quality filaments... thanks for watching !

@victorshui3104 2 ай бұрын

Thank you VERY much!!! This helped A LOT. I was able to unclog my printer and fix it :)

@irisalbarn 26 күн бұрын

thank you sooo much! you saved me and tons of my nerves :))))

@tonyballeras Ай бұрын

Thank you for this. You save us.

@mouncake7151 Ай бұрын

Thabks'to you a just fix my machine tonight, really useful video 👌❤️

@phr34kboy 3 ай бұрын

My v3 SE has gotten into the habit of clogging at the end of every print. I use mainly PLA, and the clog turns up in the same place as you've shown in this video. What I do to unclog is preheat TPU, use a candle to heat up the tip of the cleaning rod and push it in and through the clog, then burn off the residue that sticks to the rod. Repeat about twice more until I can't feel anything impeding the movement of the rod and all is well and I can print again. My problem now is just the fact that it clogs after EVERY print.

@KakiDIY 3 ай бұрын

Good tip.. Thanks !

@Murtahz Ай бұрын

You are a good man.

@ppedrohp Ай бұрын

I needed a step by step guide to disassemble it, the filament got stuck between the gears, thank you very much

@sticker.abu_3d Ай бұрын

Thank you!!! It worked!!!

@arvinvicente5212 3 ай бұрын

Thank you for sharing 🙂

@uruguayandrone4476 3 ай бұрын

Thanks, u video was very usefull!!

@KakiDIY 3 ай бұрын

Glad to hear that! Thank You

@00Hiang00 Ай бұрын

Thank You!!

@reedrichards8677 3 ай бұрын

what kind of screws does the heatsinks fan use?

@zackloomis2522 4 ай бұрын

I have an ender 3 v3 se, and Ive been looking all over online but Can’t find anywhere what type of metal the filament drive gears in the extruder are? I wanted to run carbon fiber PETG but have heard you need to make sure your gears aren’t brass. I have a steel nozzle for it already also.. Would you happen to know if they are brass gears? Thank you very much!

@KakiDIY 4 ай бұрын

Don't think they are brass.. just normal metal. The hotest I ran was 260 degrees for polycarbonate.. and normal PETG.. the drive gears worked fine for both.. probably adjust the drive gear tensioner... should be OK

@ConstableDeath 4 ай бұрын

They appear to be steel not brass, possibly a hardened steel but they're certainly more durable than brass

@medvedbubu 22 күн бұрын

Please, what should be the length of the PTFE tube? Thank you

@harrisonn5705 9 күн бұрын

Mine measured at 4.5 cm for longer tube connecting to the extruder. The small tube for the heartbreak I measured at 1.9 cm.*

@TelmaFMH 3 ай бұрын

I have a small tube that fell when I changed the nozzle, what can I do?

@KakiDIY 3 ай бұрын

Just put back the tube. It is a heat break PTFE tubing that is from the dame diameter as a Bowden tube. If you lost it, just get a bowden tube like Capricorn, cut it to length and replace it.

@juansanchezdev30 Ай бұрын

My printer has a horrible jam, no matter how hard I push with nozzle cleaner, the jammed piece does not come out, :c I don't know what else to do.

@kyuandzo 3 ай бұрын

Man its impossible to remove nozzle head. its not turning like yours. What will i do now? its looking damaged now.

@KakiDIY 3 ай бұрын

Ohuh... I find it easier to remove when the hot end is heated up. Heat it up to 250.. and try it ?

@kyuandzo 3 ай бұрын

@@KakiDIY yea i tried to remove without heating first but it was already damaged when i heat it. I just bought new hot end.

@st0rr1e 2 ай бұрын

And what if it clogs up Every time you print! It does about 5 layers into a raft and then boom clogged

@KakiDIY Ай бұрын

Try to chdck filament temperature.. or change another filament?

@st0rr1e Ай бұрын

@KakiDIY I figured out I had plugged the fa s in the wrong way so the heat sync fan was the cooling fan so the filiment was getting warn inside the hot end softening and then clogging haha