Fixing my CBR954RR Lemon

[@HeroRR]

I decided to try a video without music. Sorry a lot of the after stuff wasn't filmed after my tripod broke I just tried to power through it lol.

[@fouadkhattar]

Better without, much better, keep it like that

[@Sickling3]

Don’t need music for already good content.

[@BirdArvid]

I would not have watched the whole video had it had music; thanks!

[@MadMatt168]

The cct is a pretty notorious problem on Hondas. The xr's have pretty bad ones I hear and my dad's cbr 1000 f has had the same problem. I think that was the problem tbh, especially if the sound stopped after replacing it

[@omgsc4recrow179]

your rattle by the clutch can literally be that, clutch rattle from a worn basket, my vfr does it every tim e i et the clutch out in neutral, nothing really to worry about

[@A-Fern]

I don’t think she’s a lemon. Just an almost 20 year old bike showing wear. That thing is super clean and a real beaut IMO👍

[@SDP2031]

Agree!

[@mitsomitsara5721]

Great video! Good on you for taking the time to help everyone who loves a 954 :). Hey a couple of quick tips (apology if they have been mentioned) to help anyone watching: - Download or purchase the 954 workshop service manual. - Use a tool tray and small containers (e.g. spray paint caps) for your tools and screws. Avoid the floor. - Use PLENTY of rags/cloth to wrap parts or cover them when resting against the bike. - When lifting the fuel tank up, rather than 'prop' the tank with a can or anything else, you are better off tying a strap from the fuel tank front bolt holes (with a hook) back to the sub-frame near where the starter relay/fuse box is. - No need for a sump plug magnet > the oil filter collects ALL debris (even what would be attracted to the magnet) before it reaches any bore or bearing. The magnet DOES NOT pick up main bearing or big-end bearing material (which is generally what people want to check when intending to buy one) since the top material layer of these parts are not ferromagnetic (thus will not get attracted by the magnet). What you generally see on a sump magnet is normal wear from the transmission (gears, primary drive, any other steel etc) that as mentioned, the oil filter does. Just informing ppl to save their $$$. **If you REALLY want to have a magnetic plug anyway, you can magnetize your standard sump plug with an existing magnet using the 'single touch' method (Google it, easier than me trying to explain!). - DO NOT use pneumatic/electric power tools for removing or installing bolts. They can damage a thread, resulting in an expensive repair. Use t-bars for cover bolts. They do not need much force. - On camshaft cover gaskets or engine clutch/stator covers, you can use 'HT Dirko' red sealant or 'Black 3 bond'. - Lubricate throttle/clutch/exhaust/air box flapper INNER cables with white lithium grease. - Lubricate side stand/foot peg pivots with Molybdenum Disulphide grease. - Lubricate clutch/brake pivot points and cables ends with mult-purpose grease. - Use fuel hose or a rubber hose to remove the spark plugs after they are loosened with the ratchet. - Remove the 'PAIR' valve system and flap in airbox. You can leave all the cabling. Leave the exhaust valve (H-TEV) ALONE. - BEFORE putting fuel tank back on, connect vacuum gauges so you can synchronize the throttle body. - The 'noise' or 'knock' is NOT 'piston slap' > the pistons in this engine have literally NO skirt to cause this degree of noise. Usually (going by the video) this is acceptable for a 954 engine, could be simple wear & tear. Check your next oil change for metallic/shiny particles in drain tin - if there are none, no worry. If there are considerable particles, might need further inspection. - NEVER start the bike like you did after the oil change > instead, while looking at your oil pressure light on the display (red one), press the 'start' button and allow engine to crank BUT do not let it run. When it is about to run, IMMEDIATELY hit the KILL SWITCH. Repeat this process until the red oil pressure light goes out (it takes about 3 crank cycles), then you can allow engine to run. There is so much that can be mentioned when it comes to service/maintenance. Hopefully these few tips regarding your video help :) Enjoy all!

[@Dan_Moto]

I’ll just say as a owner of a 954. Treat her good, and ride her often. Don’t let em sit or they will have more issues than just maintaining them and riding em

[@mal3762]

that's how my uncle's bike develop so many problem it had to go full rebuilt, cus it's been sitting for years lmao

[@professorvoluck9311]

It’s better if they’re ridden but if you keep them indoors in room temperature it’s not as much of a problem. Letting them sit in a cold garage or hot sun is horrible.

[@jasonroth376]

I just bought a 954 off my friend that sat for the better part of 5 years. The bike is in overall great shape but I would watch out for dried out rubber pieces. My chain guide and my rear cush drive dampers fell apart in my hands. Put about 1k miles on it so far with no other issues

[@joetrosclair8434]

I’ve put 10k miles on my 954 since last June! I ride her as often as possible

[@joetrosclair8434]

@@JimmyTheBear hard disagree. I’ve put 10k miles on a 39k mile 954 since last June on Louisiana roads. The forks did get a service a year ago, but they are holding up like champs.

[@fouadkhattar]

Finally we saw 1/10 of his face, congrats man i hope you enjoy it

[@szymon7423]

that was his knee

[@HeroRR]

haha thanks!

[@HalfdeadRider]

@@szymon7423 You were not paying attention 😉

[@IanNeville]

I've owned a few 929 / 954 over the years and love them but they are a nightmare to work on! A few times I've thought that it probably would have been easier to actually remove the engine then struggle around the frame! ❤️🇬🇧

[@turbomike71]

I've had to do chain tensioners on all the Hondas I've owned (1995-2000)Then I went to a manual one, where you just have an external knob to turn to adjust. Because that is a job you really don't want to do twice.

[@zedddddful]

If you think this is a lemon you've been blessed I've seen some right dogs owned a few too this is just an old bike that needs a bit of TLC.

[@monkmoto1887]

These bikes are getting valuable thanks to you and that ship in Egypt

[@richardstoffel6585]

Removed cover and didn’t do valve clearance or adjustment?! That was a prime time

[@user-jt6nw6wm5q]

its not that hard to get to that point again

[@kchappelle]

Ya, that blew me away. Could have had a lot less sleepless nights knowing the valves are good to go.

[@octaviobustillos6968]

I'm going to go take a look at a 2001 929rr here in a couple of hours😁

[@joshsevens9611]

Idk if I'd call it a lemon it seems to me like it just has average wear from someone either not riding it enough or just not mechanically knowledgeable so they just road it and did there basic oil changes. Things like stripped bolts, leaking gaskets, dirty oil, bad clutch disks ECT are just normal wear and tare from time. You have to remember this is a pretty old bike it's seen a lot over its years and this kind of stuff just happens it sounds to me like you just spent more than you wanted too on the bike but she's a beut and not a sad lemon. 💪 (Btw your spark plugs is showing the bike is running to lean) ps ps Also when you do the cam chain tensioner on the 954 next time around drop the engine in the front onto a jack so the CCT isn't as tight to the frame. 👍

[@Metrobus271]

Congrats on the repair. I know it’s a daunting task, but the feeling of accomplishment is well worth it. Now you can enjoy this beautiful bike without fears or regret.

[@amorfati4111]

Maaan I am so impressed by your knowledge and your ability to fix it by yourself. Are you a mechanic or just relying on the workshop manual ? Since I've been following you for a pretty long time and since you upload not frequently. Wouldn't it be an amazing idea to start a series(for newbies) teaching us how to ? Love your work man (From Morocco)!

[@HeroRR]

I appreciate you thanks!!! I'm not a mechanic just a guy with some basic tools and enough knowledge to get myself into trouble haha. I'll try doing more tutorials in the future, I know I still have a lot to learn.

[@Nuno.A]

When you drain the oil, if you are looking for shavings run it trough a filter, like coffee filter or a white rag something along those lines, you can also use a magnet to help. Sometimes loosing the engine and tilting it a bit can help a lot giving access, don't know if that's the case here or not, enjoy your 954 and thank for the video

[@kvernesdotten]

Or cut open the oil filter, there are even "can openers" for them :D

[@darkiee69]

A cheap neodymium magnet to pull thru the oil as it drains would do the trick.

[@racimuk]

The wierd noise rattling occasionally is your cam chain tensioner..replace it if its electric (non adjustable) or adjust it if its mechanical (non electric and adjustable)

[@jrandall5995]

Probably true after all its Honda and do have history with cam chain tensioners

[@Acthungbaby]

I think not tensior its clutch basket springs .ones behind not clutch plate ones. I have sc 33 .athough my tensior seemed to not to be locking i got new one.but havent got engine back in frame . been 2 years opps .

[@chipwatson5901]

Many thanks for posting all your 954 videos. They have been a big help in working on my 2002 954

[@YoungMulahBB]

After getting my own 954rr a few months ago I was very worried about all the engine noise and did a lot of research as well. Mine doesn't make the tapping sound yours does, however mine does make a sort of clunking I notice at idle. I tracked it down to the exhaust valves where the servo cables change the valve position at 3k/7k RPM. My servo motor works just fine but for some reason I get a rattle noise from the HTEV area down there. I've read about the pistol slap as well and try not to worry about as my bike performs flawlessly. I think the valves on these bikes are noisy as well, my 929rr engine is very quiet compared to the 954rr.

[@razor1uk610]

There is more power and compression per generated by the engine, and a slightly more aggressive cam profile, within the evolution of 954's head from the 929's design, so it's natural it'll be noisier than the earlier 929 father and original 900's grandfather motors.

[@TheInfantry98]

Why would even buy a old ass bike ? That’s like putting a 50 yr old on the sports field during a soccer game expecting him to keep up with 25 yr olds lmao

[@razor1uk610]

@@TheInfantry98 why are people still buying old Harley's or classic cars, bikes, sports/team kits etc...? Or how long is the piece of rope you weren't thinking of?

[@terragaia7092]

@@TheInfantry98 why marry your crush when there are celebrities available for you?

[@frankp.9655]

So How come Honda Didn't Fix These Problems Back in the Day... Or are like Age and Mileage plays Role...

[@lesbear9828]

I will stay tuned in your CBR954rr videos so please do some update on this bike. I really love this bike.

[@Treizez34]

This video is the definition of a Motorcycle ASMR video lol

[@grahamwalters6593]

Mate, It’s a pleasure to watch you work on these builds or such, You do a great job. Cheers from down under.👍

[@marcusgeorge1825]

I love your approach and patience. Having also done this on several different bikes (over 20 years). Today, I just don’t have the time. So I only buy new and utilise warranty for any potential issues. For me this is a trip down memory lane. Keep up the great work you do as it’s great for others to understand how complex it all is. 👍😎🇦🇺

[@joelbrittenour8197]

After watching you work on this bike makes one appreciate how nice your vfr is. Also some things easier to work on vfr. but you hung in there.

[@menom7]

I remember installing an electronic gear-indicator for my 2000 CBR 929 (which is basically the same exact thing) and yes,NOT AT ALL being a primo "wiring" guy,it took me FOREVER on figuring out WHERE to hook stuff into,but surprisingly,it wasn't all that difficult! The MOST difficult thing,was having to reroute all the wiring stuff around everything to keep the wiring hidden. Great video HeroRR!!! :-)

[@sanderslongdrive]

Very well done. A rattle that goes away once the bike is warm can be a cracked exhaust. Look for smoke down the line when cold / feel for a blow.

[@ronaldtartaglia4459]

Been watching for years. Finally saw a glimpse of your face. 🤣

[@markypea]

I had a 929, loved it, great trip to the Nordschleife. Clutch rod broke whilst I was in France, had to ride whole 400 miles back with no clutch, lots of running to get up to speed and bonking it into first. A year later, on the track it kept refusing to go into 3rd, or dropping out of third mid-corner, which was not cool! I sold it to get an CBR1000RR6, with the cassette gearbox, so that if that started playing up it would be an easier fix. I track-dayed that for nine years, never let me down. Was literally the perfect bike for the track. I didn't use it for much else, I think because it's begging to get leant over and I had some dodgy moments from enjoying some knee down fast corner stuff, you just can't cruise about on it. Sold it 2022, just bought a CB600 as I do miss biking though!

[@malur10]

Good to see u back in action

[@Blackbirdrod81]

Well done on the repairs Hero. That was a massive job. See how you go, if your are not happy, get another one.

[@chrisdigital]

Those bikes are amazing, keep it going forever. Next to the triumphs Thruxton RSIO now, this was my all-time favorite. I wish I never sold mine.

[@tomintoxicated]

My 954 makes the same noises yours does. I replaced my CCT as well. I found that after doing the valve clearances (because they were waaaaay out) that it made more noise than before so I think it's mostly the valvetrain. My mechanic stethoscope doesn't pick up much noise near the crank but a lot by the valve cover. You should check if yours does the same.

[@kaiser98berlin]

I don't have the precision stethoscope such as yours but I used a screwdriver with a solid end for hammering by putting it at my ears and the flat head towards the CCT, valve cover, block head and finally found the clicking noise to be coming from the HGEV, HTEV? it's the exhaust valve. Somehow warming it up for awhile and riding it would eliminate the noise. Amazingly the exhaust valve motor still works for mine.

[@sandonpreston7529]

I've had my 92 VFR for 20 years. It still kicks ass. The only inline four that I would buy is a 1976 cb400/4 or an early 70's cb750.

[@sinbadeatinamcrib5960]

Step 1: Drain and remove gas tank. Step 2-37: Everything complicated. RR: I'll just go ahead and skip step 1 to make everything harder.

[@Libertà_sulla_vita]

You dont have to drain it. Rubber bung plugs work great..but yeah i agree, pulling the tank on a job like that will make the job a lot easier.

[@basithph8958]

Good to see this bike back again! Can’t wait to see the 954RR do some rips🔥

[@gripnrip3489]

Yes sir that slap was always super noticeable on my 954 when I had it. Something you should look into as well is some case cover protection. I went down in gravel at 15mph and my stator cover blew apart and in the process the mating surface on the actual engine at the bottom of the cover completely snapped off.... I cry still even after getting a new bike. I miss the 954

[@SaqibKhaliq]

Great work here. Considering how black the oil was.. the inside of the rocker cover and head looked very clean. It’s an older bike now, so have to expect these things. Great work, bike looks ace 👍🏽

[@NudaMan]

Raced a 929 or 954 on the freeway last week with my 2003 Aprilia RSV MILLE, he was quick af but I was right there with him 👌🏾 made me wanna get one lmao, these older bikes are gems I swear 🥲🔥

[@hiroshiphillipnakamura5358]

I have an 01 CBR 929RR that is damn near bullet proof. She has 110,000 miles and will still do over 150 m.p.h.!

[@jasonwhelan5596]

Changed a cam chain tensioner on one of these last year, a nightmare. I done something very similar to what you did with the 8mm spanner.

[@ArcanePath360]

Imagine the cost of handing that over to a mechanic. You must feel good about the money saved, even though it was a horrible time of it. I've been there, and that's what I tell myself to get through it and make it seem better.

[@Z32andCG6]

I've done a lot of these things, and some others, on my 600rr and it can be finicky but rewarding. Good work 👍

[@undisputed1one]

Fun trick, you can wrap around a ratchet strap around the front of the tank and behind the rear foot pegs to keep the tank up. Appreciate the hard work tho, good vid!

[@HeroRR]

Thanks!

[@dancarlos1216]

honestly easier to take the tank off rather than fighting it and ducking underneath it.

[@paulhall170]

All of those problems are problems I'd love to have just for the privilege of owning a 954...

[@greylove1522]

Really nice bike I don't think it's a lemon. They always had noisy transmissions. There was a recall on them for something transmission related. You did a great job checking it out. If you didn't find anything, just ride it. Cool video.

[@Mike.Mendes]

Keep it up man, I love these bikes and these videos. Thanks

[@Ky_Mycology]

Sounds like a lifter possibly, but I would do a manual tensioner for sure.

[@J2A61]

Just got off mine, I had the head bearing replaced on top on the handle bar collar, new front tire some plugs and the thing fly’s!!! I probably will never sell mine

[@suddendilemma5137]

I think it’s gorgeous. You’ll get it sorted and it will be glorious.

[@Amaturehourwithmike]

Dang. I rebuilt the engine on a 929 I bought about a year ago, and watching this is taking me back. lol

[@Libertà_sulla_vita]

Another tip, trust when i tell you, removing the tank will make youre life much easier on a valve cover removal. Sometimes, if its an easy job, ill put my bike on the stand so it sits upright and ill attach ratchet straps to the ceiling of the garage to pull the tank up so i dont have to disconnect the fuel lines. Working on these street bikes is a pain in the balls but its better than paying $100/hr mechanic 😆

[@thatoneguy985]

I love my 954. Has rebuilt title and needs a little love, runs a bit rich but i think it has a tune on it

[@okie-rider]

Dang piston slap strikes again! Nice video. Don’t worry about the haters and critics, it takes guts to make videos and put them out there!

[@HeroRR]

Haha it does. Thanks!

[@filamrider]

I miss my 954 bladed it was my second bike after my gixxer 600 back in 05.... heavy but man she is nice also considered a liter back in its her heyday.. Nice bike.

[@kristinh5524]

Love that 954 I want it so bad! Have fun be safe!

[@AccountTake3]

Camchain tensioners are a known problem with Honda. Had the same issue with my ‘94 CBR 600 back in the day.

[@avio92romano]

This video inspired me to get my own 954rr

[@thomaswarren2699]

lol that stripped screw right at the beginning lol I know the pain. Giving my '97 CB500 a once over and one of the three screws that hold the air filter cover in place is just spinning in situ- need to think outside the box to get that one out.... hmm... Nothing gives you a boost of enthusiasm like falling at the first hurdle hahaha

[@anthonyoberliesen9040]

Don't bother replacing the flapper in the air box, you don't need it. It is your bike though so, you do you man! I wish I still had mine... I miss it...

[@Koukilin]

Hella fast with that oil plug removal my guy😆👌🏽👌🏽

[@christianmartinez7161]

I like when he said if I have to pull the valve cover again then I'm just leaving it hahaha

[@YoungMulahBB]

YES been waiting for this video! Just had to say that, i'll watch it now.

[@charlesjohns3003]

there is a tank-stay rod clipped under the riders seat ! to hold up your hinged tank! also the cam chain adjusters get noisy

[@armandblake]

Man... this bike is just pure class

[@mikepohl2264]

I'm so glad you got things sorted out!👍

[@HeroRR]

Thanks!!

[@teokastelan2930]

Nice bike. I love this generation of Cbr.

[@markwilkes4318]

Back in the day when I was wrenching I wouldn't worry about what length bolt went where. Upon reassembly I would insert the bolts and if they were all even I knew they were in the right place. Most of them are pretty easy to figure out.

[@alex-thangnguyen2746]

Bikes are fun. Wait until the diode to the neutral light goes out, lotsa fun. The neutral switch goes into the engine crank and sit on the shift drum, the neutral slot for "frame ground." As the switch wears, it will shave a little off but the shift drum will also "flex" with the switch. Typically, hot oil will leak and get on the wires requiring a new connector (easy, cut it off and solder new one). So you can save that neutral switch, universal on other Hondas, still good if you polish it and remove the corrosion ($1 lime-rust gel). Tapping sounds are common, especially V8s. A tapping sound at startup is always VALVE related, in this case, piston slap. There are books on how to diagnose an engine by noise (Hughes). It will remove carbon around the valves if you add a gas additive. Bikes are even more fun now.

[@HeroRR]

Do you think the tapping sound left unchecked would cause a problem? Or just wait for it to go away before riding and I’m good.

[@alex-thangnguyen2746]

@@HeroRR Tapping sounds are common and do not pose any serious harm to an engine, however, they are annoying! They do not go away either. The only thing I can tell you is it is related to your valves, intermittent. The question is how badly do you want to fix that annoying sound before the engine warms up?

[@traviswade1822]

So not looking forward to the cct change on my 954... but ive had some interesting times with an htev delete and a power commander 3... but now I know what I'm looking at thanks for getting what you could filmed...lol

[@kronos350]

I owned 3 of those bikes, greatest bike ever.

[@vagueWhelk]

She’s a beaut! Good work dude

[@kvernesdotten]

Good job man! Piston slap not being a big deal sounds insane to me, but im by no means an expert. On cars that could be pretty expensive where a machinist needs to bore out the cylinder and get slightly bigger pistons to compensate and all that. But hey, maybe the tolerances are just smaller on a bike, I dont know tbh

[@gsxrfrank8787]

Lemon most definitely not just a great looking bike with minor issues and it’s issues that are aged in time

[@Kells1379]

Awesome job and such a beautiful bike.

[@MayorMcCheese47]

Dang that chain tensioner is in a tricky spot. I got lucky the one on my CB919 is thankfully out in the open lol. I noticed the piston slap on mine too and thought something was wrong too hahah

[@uptownsamcv]

back when I had my F4i the clutch would rattle at idle and would go away when I pull the clutch lever. the inner clutch busket nut had to be retorqued.

[@rhemyis]

I have the exactly same problem in my 06 F4i, please give me more information about this. On Honda forums this issue is very common for cbrs and almost everyone says to just ignore it. My bike has 20k kilometers, should I go to a mechanic urgently or just leave it like this? I have good mechanical skills, if it's something easy to fix maybe I will try to do the job, what do I need to change/fix? Thanks a lot

[@uptownsamcv]

@@rhemyis there's really not much information to give. I remember the clutch cable having too much slack and a new cable didn't solve the issue. So I pulled off the clutch cover to see what was going on and the inner clutch basket had some play and would move in and out a bit. I ended up getting a new nut from Honda and just torqued it to spec.

[@nhzxboi]

Haha! Was going to say piston slap. Short skirts aren't only sexy, they're noisy in cars or whatever. Generally harmless.

[@VytautasValaitis]

Check the valves!! It is 10 minutes job at this point.

[@SDP2031]

Great video as uaual! It might be a very good idea to fix the valve clearances and do a throttle body sync at this point.

[@chincemagnet]

Anything to do with the top end on these bikes it’s quicker to drop the engine down, simply because there’s no room. Personally I would have tried to stop the leak, but as long as it wasn’t a major issue I’d just live with it 😆 until I had to get in there for some other reason. I have an 04 F4i, our bikes are very similar in design. I blew out a spark plug last summer, what a nightmare. Ended up swapping the engine because it was the easiest and most cost effective solution. $600 got me an engine with 14K miles, mine had 38K.

[@georgiosphilos2146]

Spark plugs look a bit white. Either it's a bit lean or maybe check for coolant leaks

[@SoSoGone02]

My cbr600f4i is the same struggle with the timing chain tensioner. I hate it. Working on just about anything on the bike is a pain in the butt. But damn do I love the bike at the same time lol

[@myztklk3v]

its not a lemon if you bought it off someone who just didn't take care of it.

[@kchappelle]

At least they didn't molest the bike. Just that ugly exhaust can and no rear fender. I'm getting one next week and it's totally stock.

[@valerie_screws_around]

When you opened thet clutch cover i was wondering, how is everything SO CLEAN?? Where is the oil??

[@jensenmiller6410]

Most engines are clean like that on the inside. Oil filter catches 99% of the dirt and oil is remarkably clear when it's a thin film. They usually stink to hell on the inside though.

[@cgbomac2cryptic447]

Hero I have a 954 since new 2002 Your engine sounds normal . Keep it stock maintain it well,ride it a few months then I'm sure it's an original fuel pump so go ahead and change it out for a stock oem honda pump no cheap sh*#t. Trust me you can thank me later. My bike was lagging just not like brand new New fuel pump bam! Sucker is a rocket 🚀. Enjoy 954 best most accurate steering bike I have ever ridden. Surgical.

[@Obulisc]

Not going to lie you make me think of a motorcycle Chrisfix I hope you get as big as him

[@dalehawkes1698]

Great video I had a 954 new lovely bike ,if I was you if the oil was that disgusting I would change &flush the coolent as a well ,you don’t want her over heating .👍👍🏍🏍🎉

[@steelcityspeedshopj.r6942]

Half the fun of owning them is fixing them man !

[@mmotorcycles9497]

Agree 100% with steelcityspeedshop

[@vytas5584]

5:21 Hey dude thats not from a mouse. Ive seen guys on forums talking about an "air box flapper valve" mod. I believe thats what you are looking at there.

[@seagangvision2736]

Thats my dream bike Hope one day will have it Greetings from Bulgaria

[@khalidabu-saleh2081]

Yo, new post! Can we see the vtec bike again. Just got one because of your VFR videos!

[@HeroRR]

Hopefully! I still ride it a lot!

[@khalidabu-saleh2081]

@@HeroRR Nice! I hope it treats you well! My reg/rec went out recently, apparently it's a common fault with the VFR800. Still love it though.

[@douglasalexander4348]

That’s why people pay $$$ for new bikes. It’s not a lemon, it’s had 20 years amateur maintenance. Bikes with a cheap micron exhaust are a bit of a giveaway. Flush brake fluid, do a valve clearance, new gasket, plugs and air filter and replace cam adjuster. 1/2 a day. Next will be fork oil replacement. Seized stripped bolts on a 20 year old bike is par for the course.

[@4u2nvcpt]

Next time you remove the tappet cover, loosen the bottom part of the radiator n swing it forward. That should give you room to remove the cover that way

[@p.chakraborty4453]

Good bike choice.

[@lorangajapp8086]

So the gear indicator goes to the yellow wire and the blue connector?🤔

[@rider_bravo]

Hi, When you replaced the cam chain tensioner did you put pressure on the cam chain so that it is held in place so that cam position is preserved ? If not the timing goes off. At least that's the case for the Triumphs. Thanks

[@razor1uk610]

I think you slightly mis worded what you wanted to say.. or intended to mean. Please redraft/edit your comment to be less backwards. Thank you 😊

[@josetirado985]

Glad it all worked out!!

[@uptownsamcv]

i hate allen bolts. on my 08 CBR1000RR fairings, I used stainless steel M6 and M5 phillips head screws from Lowes.

[@crepguardiola]

Previous owner stripped my bolt on my 2007 CBR 600RR too 😩 pain

[@Acthungbaby]

Its the clutch basket springs mine very loose .its more anti rattle thing so not needed just sounds naff.the springs behind i whouldint worry .u cant get new baskets .i looked ebay .but hard to see there not the same .

[@Atomic9t9]

Where did you get the new drain plug from? That’s sick! I need for my f4i

[@harryhoudini3537]

Hero, I like the way you fix and mod bikes. I have a zx10r and enjoy it to the max! It's like your 600, now you have a 954, which I think is more awesome than the 600. When I commute, I use my ML350. I can't see the need for an RC51 or a VFR, or even the 600, being a minimalist myself. Do you have a car? My car is a TPC turbo Cayman, you can see them at grudgewing2732 on Tumblr.