Flip Down Edge Guide for the Industrial Sewing Machine

[@AlexanderDyer]

Hi, Thanks for checking out my video. Please subscribe to my channel and click the bell 🔔 to be notified every time I post a new video.

[@xaviercruz4763]

Hi Alex, hope you are doing very well. Whats the camera?

[@AlexanderDyer]

Panasonic GX8 I have links to all my gear in the description if you are interested. Thanks

[@PINACI]

I use a round 20mm x 10mm neodymium magnet as an edge guide on my old singer 201k so for those who can't find edge guides for your machine then that's an alternative, just magnets on and comes off when needed.

[@AlexanderDyer]

I use magnets too, it works good. kzbin.info/www/bejne/kJi4g5msgJh5g7c

[@NITEGOD]

I have the same exact machine and also a Sailrite LZ1, I also make bags ,love your videos they are great thanks for sharing your knowledge...

[@AlexanderDyer]

👍

[@roxannericchio3556]

Just ordered one for my Seiko STH8BLD-3

[@docreaper6449]

Some of the screws have fine threads while others have coarse threads, if you can’t get going or it is tough to turn, thank you screw to the hardware store and get the correct screw (my 1541S took fine threads)

[@myzlyn56]

I've been watching your videos for a while to see which would be a good machine for me. In a few weeks my Juki 1541s will be arriving. Which accessories do you feel are essential for a beginner to have a successful start. Thank you your videos are always very helpful.

[@AlexanderDyer]

A good pair of scissors and some good quality thread, with appropriately sized needles. Then just practice.

[@dusty265]

Just found your channel, super great information, I have been looking for something like this, I use a singer 111W151, love the machine but a edge guide would be great!

[@AlexanderDyer]

I am not sure if there is a mounting point for this style on the old 111's. But there are other options. I like magnets and use those from time to time.

[@y2keefus]

I see that most places don't advertise this fitting a Juki 1541. Many suggest the GB-6, which doesn't look as nice, and I've heard that sometimes the bearing isn't centered. Do you know if this one will fit a Juki 1541? I would think it does, but I'm in the UK and ordering them is more expensive and takes a month, so I want to make sure. Thanks again for all the content.

[@AlexanderDyer]

It will fit the Juki 1541

[@y2keefus]

@@AlexanderDyer thanks for the quick reply.

[@JoshLathamMVC]

Great to know I can get something like this. I have the exact model of walking foot as you too, so it should work fine for me.

[@AlexanderDyer]

A fortunate coincidence.

[@SmashTactics]

It's a shot in the dark after so long: but what presser/walking foot assembly is that? It looks much thinner than anything I have. I've Got the edge guide, but my assembly is too wide. Thanks

[@AlexanderDyer]

Something like this www.khsew.com/index.php?route=product/product&path=180_259&product_id=445

[@SmashTactics]

@@AlexanderDyer You're a prince. Thank you

[@orionshomeproductions]

I wonder if it will work with my new tech gc 0303 it's supposed to be basically the same as juki 1181n

[@annebenvenuto8264]

Great video thank you. I notice there are various brands/models and the price range varies from $27 to $60. The one you link is about $53. Can you tell me what might drive these price differences. Do some have different adjustment features are some more/less sturdy stay in place etc? Thanks in advance. Anne

[@AlexanderDyer]

I only have this one, I can't speak to any of the others, I just have no experience with them. I have been very happy with this model and if I was to get another I would go this route again. Good Luck in your search and thanks for watching.

[@gumwap1]

Basically machining quality and fit & finish. The Kwok Hing he is using is high quality and made in Hong Kong. They make very high quality import machine parts. Worth the money. I’ve had cheaper guides and they usually have something slightly askew about them. They work, but I think the extra price is worth it to get a top- notch guide.

[@stoneblue1795]

I like it. Question though, is that round part of the guide (that meets the material or leather in this case) an actual bearing or bushing that rotates, or is it just round in nature or shape?(great video in any regard Alex, thanks).

[@AlexanderDyer]

It is a roller wheel.

[@cvasoyan6065]

Great question

[@notgivennotgiven7776]

I was gonna ask the same thing

[@blancherutherford4764]

Could you show us how to install this suspended guide on an industrial sewing machine

[@embeaston]

I believe I was one (of the many) that commented on the edge guide. So thanks for this video! I like that smaller foot in this video. Did you cover the different feet you use for this machine? I actually just received this machine today and want to purchase a few extras. I’ll check out your affiliate links. Take card

[@AlexanderDyer]

You can get that foot set from nickosew.com. Tell them Alexander Dyer from KZbin sent you. Thanks.

[@embeaston]

Alexander Dyer great thanks!!

[@1goddarddr]

Just put this guide on my consew 206rb 5 it attached in the factory holes fine. It flips up and down. The guide horizontal adjustment is only 1/8" - 3/8". I was expecting more adjustment range as in your video.

[@AlexanderDyer]

I suspect that either something is wrong with your guide or perhaps a set screw is limiting your guides travel. Take another look at it and if it is malfunctional then you should return it through amazon and get another. Mine adjusts anywhere from 0 up to 3/4". Thanks for the feedback and let me know how it turns out.

[@1goddarddr]

Thanks for your quick reply. I can see the problem. The two mounting holes on my machine are not allowing the guide to mount to the right far enough to allow more adjustment range. I mounted the guide using only the right hole moving the guide to the right 1", which gives me plenty of adjustment. But, only one screw is holding the guide now. Seems tight and holding but will probably loosen with vibs

[@AlexanderDyer]

Another thing that helps get me to an inch is that I have such a narrow foot. If I had a wider foot, that would shrink my adjustment area. Too bad about the fitment. I am imagining a 3 hole plate to mount between the guide and your machine lining up two holes to mount to the machine and the third hole to line up with where your guide is now, The center hole would be shared at the machine and the guide. Sometimes I use a magnet net too on other machines so there is that. I appreciate the information.

[@1goddarddr]

great idea, Thanks

[@RivBikeWorks]

What is that skinny foot called? Looking for something narrower than what I have on my Juki DNU-241. Enjoy your videos and spreading the knowledge!

[@AlexanderDyer]

I got that foot from nickosew.com Call and ask for Nick and tell him Alexander Dyer sent you. Thank you.

[@RivBikeWorks]

Thanks Alexander!

[@freedragonfly]

@@AlexanderDyer his website is down, is this the correct one?

[@cp3onmtv963]

Alexander, can you confirm if this guide will fit the Consew 206?? I have 2 screws in the back that seem like they would work, however the bar lift at the back hangs right above one of the screw holes which I think may prevent me from putting the foot all the way back down. Wondering if maybe you tried it on that machine before this one :). PS thx for the vid on this!

[@AlexanderDyer]

Check before you buy but many sellers on Amazon accept returns but I am pretty sure it will fit your 206. I can't actually confirm that but I will be very surprised if it doesn't fit. I think the ad actually lists the 206 as an option, check it out. There is a link in the description. Thanks.

[@cp3onmtv963]

appreciate it, I'll give it a try, thanks!

[@barrypotter9527]

Will this work with the jack h2cz thank you great video 😀

[@AlexanderDyer]

I don't know about that one. Check the back of your machine for the screw holes that I show in the video. kzbin.info/www/bejne/h368nqKejNd7e5o

[@Braz1956]

In the link you gave, Kunpeng doesn’t list that guide, KG867A, as fitting the 1508. A different guide of theirs, GB-6, they do list as fitting the 1508. Can you verify which part # you are using? I have a 1508.

[@AlexanderDyer]

I looked at it and it does list the 1541 which has a very similar case to the 1508. This is a new model number but it mounts the same and will bolt right up to your 1508.

[@tangfj]

Any idea if these will go on to an Adler 167?

[@AlexanderDyer]

I think most of the older models do not have the two threaded mounting holes needed for this type of guide. Stay tuned for upcoming video for ideas for such a situation. 🌞

[@yogiecastillo3690]

I love it. But i can't find the link to buy 1

[@AlexanderDyer]

Click "SHOW MORE" in the description below the video.

[@glenn20081965]

Can these be used on a non walking foot industrial machine?

[@AlexanderDyer]

Yes, if they have the mounting screws. Here are some other options kzbin.info/www/bejne/pWSTZIeDhq1jY5I

[@theresaeastman3995]

I would love one of these. Not seeing the link as to where to purchase one can you tell me please

[@AlexanderDyer]

I put that link in the "description" which resides below the video. You may have to click the "show more" option to see it. Here is the link for your convenience. Thank you. amzn.to/2o3pejC

[@lisalamanna4459]

HI Alex- will this fit my Juki LU 1508NH? or is there another version for my model?

[@AlexanderDyer]

No, you should be good to go with this one or one just like it.

[@JENNISWISS]

super cool tool👍👍👍 thx

[@raghuarmani8341]

On my machine there are no holes to fit this and not enough space to drill 2 holes. Any ideas?

[@AlexanderDyer]

Yeah. kzbin.info/www/bejne/pWSTZIeDhq1jY5I

[@deltajohnny]

Very helpful video! Thanks a lot 👍👍👍

[@AlexanderDyer]

Thanks! You are Welcome.

[@angusross7922]

Has anyone drilled and tapped a Juki DU-1181N to take this kind of flip down edge guide??

[@StumptownDiesel]

Do you happen to know if that foot set will fit on a Juki LU-563?

[@AlexanderDyer]

Nickosew.com and tell them Alexander Dyer sent you.

[@DeclanGreen]

I have sewing machine envy now

[@AlexanderDyer]

I'm glad to help.😉

[@bowtiemenswearllc7945]

Do you think it can work with my juki DDL 8700

[@AlexanderDyer]

Just look on the back and see if there are two threaded mounting holes.

[@bowtiemenswearllc7945]

Thank you 🙏

[@mohadhassan5458]

Where can we get this?

[@AlexanderDyer]

Follow the link in the description.

[@rosariomendoza9204]

Gracias pero no entiendo su idioma. Bendiciones