FlySky FS-i6 Betaflight Setup: Calibrating Endpoints

Please consider supporting me via Patreon at: www.patreon.com/thedroneracingengineer
If you fly Betaflight, Cleanflight, or KISS, you need to correctly calibrate your channel endpoints--no matter what transmitter you use. I'll show you how to do this using the FlySky FS-i6.
-- Product Links --
Links below are affiliate links. I will receive a small commission if you make a purchase after clicking them.
FlySky FS-i6X with A8S receiver
* Banggood - goo.gl/XG43Jr

[@plainuser48596]

You didn't tell people most important thing about this radio - you save settings by holding "cancel". Many people change settings then fail to save them and are lost in trouble shooting hell. Also this radio with 14 channel + timer mod is awesome. I even put taranis pr10 gimbals on it just for fun of it.

[@clint351mx]

Jesus thank you for this...why does nobody actually go through the full process and show you how to save what you just did instead of resetting it each time you hit cancel to try and get back to the menu..

[@LBitoeverything]

🤣 True😂

[@elad3958]

that is so funny that this is most likely what I need.

[@wolfgangehrenmuller9248]

thanks mate!

[@williamhenson3217]

3 yrs after the making and still a great video! thx so much for this! First time FPV flyer and could not figure out why my drone was pulling to the right when the sticks were at center. This saved me so much trouble, thank you!

[@jasoncross6151]

Thank you JB, really pleased your showing more TX's than FRSKY. 👌🏼🚀😎

[@reallyfpv993]

Just helped me again! I have a qx7 endpoints understood. Didn’t know how to set them in my FS-I9. You made it quick and simple. THANK YOU!

[@JoshuaBardwell]

Try using the Betaflight rxrange command. Skip the transmitter.

[@reallyfpv993]

Joshua Bardwell I will do so. Thank you JB!

[@calebjared75]

JB you totally didn’t have to do this video with a Flysky but I am so glad you did. Thanks for not being a snob and helping us who are just starting out!

[@abundantYOUniverse]

Man I almost clicked out of this video and then wammo at 5:00 you tell me how to make that damn thing go to the second end point. I have been trying and looking for a week! Thanks you da man!

[@zatteroger544]

Hello Joshua,I am very pleased that you are giving this radio some love. In my opinion it is the most capable radio in the sub 50 EUR price range. (Even sub 40!) There is a 10 channel software mod that also give the possibility to set a timer, voltage alarms etc. For this software I refer to the rcgroups FS-i6 tread. I wouldn't mind you reviewing this radio a bit more in detail as I didn't known this setting for example. Many folks are using this a first radio Especially when the Q X7 wasn't around yet.

[@jordanbentley]

4 year old video solved a long running problem of mine and shed light on issues I have seen others have constantly just incredible

[@KrotowX]

Thank you. I already moved endpoints as you're described there two weeks ago for FS-i6X transmitter which mine coworker bought for his Wizard X220. Such transmitter after month of flying had all channels shifted by +2/-4 with middle point in BetaFlight around 1506 by default. Which caused drift and impossibility to arm without pulling stick down by force. Cheap Chinese stick resistors in glance. After endpoint tuning it now have correct ends and center.

[@youeladamas7840]

Great tip for the beginners most ppl that start in auto level modes never know why they are getting drift or uneven control in turns. Even intermediates have issues with why they cant flip or roll to one side the same. its also good to calibrate sticks evey now and then on flysky remote for sure when you get it

[@deadbeatbrad5484]

I've been using that radio for almost a year now. Absolutely great for $50! Thanks for showin some love to FLYSKY!!

[@WildCaptures]

Thanks for explaining Endpoints and Subtrim on Betaflight, I'm one of those never do it guys😓 Now I will👍

[@discord2000]

I've recently abandoned my turnigy evolution to go back to this radio full-time... The 14 channel firmware mod is amazing! rssi display, configurable timers and alarms! love it!

[@robertlunsford1350]

Another excellent tip. I guess I was halfassing this but it makes a lot more sense after you explained it.

[@thomaschavez2969]

Good info. My fs i6 didnt need too much trim adjustment, but my spektrum dx6e needs to be adjusted to nearly 150% to make the end points where they need to be. I also experienced the importance of doing this when I was doing a micro brushed build. The transmitters min throttle was around 18% throttle, so it wouldn't arm since you couldnt go to an actual 0% throttle.

[@1grizzlyrizzo]

Thin light and cheap, great little setup, and the 10ch mod opens up a whole new world. Best thing since sliced Spam.

[@1grizzlyrizzo]

Hachiro I'm running an fs-x6b receiver with the tgy-i6, and it has the voltage telemetry. So no need for me to have the i6x.

[@ksarrow]

Thank You again Joshua. I still have a FlySky and wow you whipped one out and saved me a bit of trial and error figuring it out.

[@senditfpv6538]

I've found when using flysky it's better to use ibus instead of sbus. Ibus automatically sets all the endpoints and centre points

[@JoshuaBardwell]

I would be surprised to find out that was true.

[@OriginalGingaNinja]

Tony Peart I've used two different ibus rx's when I was using as i6s TX. I had to set the end points on them both myself.

[@DanielR8484]

i use ibus to... it is perfekt

[@ZeroFPV]

Albert Kim made a video about this.

[@tehllama42]

I run IBUS primarily because it avoids the inversion issues encountered with a lot of F4 boards. The pairing of the i6 (i6x) and the A8S and A6X receivers are the best way to get into the air cheaply, although I'd still recommend the Turnigy Evolution for anybody looking to get started who knows they'll want to fly thumbs.

[@dronexfun8469]

This radio is awesome for the price. I use the irange irx6 module for flying different brand quads and because this setup is so cheap you can leave a radio in your car, have one in the garage for indoor, one in the house for indoor and one for guests. Saw one on ebay for $32 new, free shipping.

[@pablofpv]

Now the secret is out ,the price will go up! Its good that you have finally discovered it ,as its a really good tx for the money. I have the Eachine version and updated it to the 10 channel mod and then ,RSSI version , I then updated the firmware on the FS-IAB6 with a ST link tool to 1.6 ,this then gave me RSSI on my TX screen and more importantly in my OSD! The number of channels and lack of RSSI were for me the only things missing from this radio. I also de-pinned the FS-IAB6 (why? ,has the greatest range)and it was more compact and now 6 grams lighter. Photos below. I was going to make a video of the whole process ,but I then bought a newer FS-IAB6 (RX) and before I installed it I copied the firmware and they now seem to be on 1.6 ,also this radio is rebranded as a Turniby ,Eachine and Flysky(all the same ,different firmware and easy to change). The FS-IAB6 is a 6channel receiver ,but the you can use ibus (better) and you get more channels. The gimbals are probably not as good as a more expensive TX but they work and the replacements are cheap ,I have thrashed mine constantly on my quads and simulator and still going strong ,but yes it does jitter ,just add 5 for dead band. If mine breaks ,I would buy the new 10 ch version £37! what value..... It proves you don't have to spend a fortune to get into this hobby. www.dropbox.com/s/9306apvjghha33t/20170609_175237.jpg? www.dropbox.com/s/i8hatvl6xz6celq/DSCN0410.JPG?dl=0 www.dropbox.com/s/og982qihc1pa6my/Original%20Eachine%20Racer%20RX.JPG?dl=0

[@paulmorris563]

Got the i6 (locked menu) with my eachine falcon 250 rtf last year. Since then I have built 3 of my own and I'm on the fourth (RFX 185) and I still use the i6. It has been a champ and I'm not even considering upgrading anytime soon.

[@dlevi62]

I appreciate your help! You make it much more understandable than just about anyone else. Thanks!

[@jkomjkom7064]

Thank you very much for that most important information, it pleasing to see you helping all pilots at all levels. Love your vids, been following you for long time, and this is just great work your doing keep it up mate.

[@tabdougherty8549]

I still fly these! I am constantly worried about range but it is worth it while you build your inventory of parts and batteries for quads. Q7 OR taranis is in the works.

[@ProppedNutFPV]

Thank you for using Flysky as an example. It really isn't a bad radio. The only thing I'd like to bring up is the fs-A8S. Extremely bad receiver. Check out RCgroups "FS-A8S Help" thread. Now the fs-x6b is a really nice reliable receiver. Only issue I'm having is setting up failsafe. I've installed BF 3.2 on my quad.

[@tehllama42]

The A8S (per the manual) is incapable of failsafe... although I was able to get it to act somewhat like a F2 Failsafe in BF3.1.7... that said, because diversity for such a small weight penalty is better, I recommend the X6B as well... I have had a great time with my trio of A8S receivers, but there are moments where I can tell I'm losing RC signal and crashing as a direct result.

[@carloshnunez]

Thanks for this video it was helpful 🙂🙂👍👍

[@KythForsa]

Great stuff as always! Would like to see a video about what to do when you adjust the endpoints as far as they can go and you're still not sitting on 1000-2000. I have a DX6 with some DSM2 receiver (on a whoop) where I can't get the high end to 2000, only to like 1840 or so. Maybe there's some trick on my radio to allow adjustment beyond 150% but in any case I learned about "rxrange" in betaflight which can resolve this problem (and also allows to reverse the channel thus averting having to do it on the radio).

[@JoshuaBardwell]

Yes, rxrange is the answer.

[@1Esteband]

I love the I6 form factor, light, thin, nimble. It would be beyond my wildest dreams to have a Taranis with this form factor and weight.

[@Ultrazaubererger]

I noticed that after using subtrim i had to readjust the endpoints again. Also you might want to mention that there is great community firmware for the FS-I6 that can make it even better. I now have a timer for example.

[@JoshuaBardwell]

Oh damn that's a shame. On most modern radios, adjusting Subtrim should not affect Endpoints, but older radios (and apparently this one) do that.

[@OriginalGingaNinja]

Dave Interestingly it doesn't do that on the i6s, different firmware though.

[@tehllama42]

The i6s and i6x run different firmware - I can try to look into if subtrim adjustments affect it on the i6x

[@Ultrazaubererger]

I just tried it again because i wasn't sure anymore but yes, the subtrim directly affects the endpoints on my Ideafly branded FS-I6 with flyplus beta and an afhds (not afhds2) receiver (built in to the board).

[@tamarathompson9418]

Me and my mates fly this transmitter . I will eventually upgrade . So i can use tbs crossfire . Cheers for the video

[@g-trooperg5876]

I love my cheap FS-I6, I can trash it and buy another if needed! The 10 channel mod is sweet.

[@flyingfinnstarRacing]

Thanks Joshua! Another happy subscriber after your video helped me solve my problem. You're the man!

[@gavlarfpv7841]

I got the already 10 channel grey stickers tx, had to go into menus as it's on 6 channels default, great for the price and easy to use, have used the fsi6b receiver with excellent range and now got a new design for copter flysky x6b with the dual antennas which are changeable, heard it got great range too, up to 2.3km on KZbin, only need couple hundred metres 😄

[@AlexApol]

If he does a review on this radio he needs to show the 10channel hack. I did it this afternoon. Works like a charm.

[@blindfpv5763]

Nice video josh,it's very helpful for many of us like fpv noobs.thank you

[@ched999uk]

Great to see a different tx. i6 is great, amazing for the money. Thanks

[@soumoychakraborty6160]

Many many thanks to you.I was not able to arm my drone now I did it configuring in these values..Thanks Sir

[@SteelTallon]

Thanks! i forgot about sub trims. I just built my 1st racing quad, and have some trim issues on startup. Sub trims will help with that. I did however do my endpoints.

[@Kriswixx]

knocked it out of the park. THIS, out of 50 videos I tried to find, I finally got it!! I had to reverse a few things, adjust a few settings. so stoked.. as always, hold control to save these settings, yes? This is my controller!! any other info, links about this controller or any flysky stuff, let me know. Im having a pickle of a time. I feel i made progress today. time to zzzz. ( i get a few hrs a night a few times a week to work on this only).thanks man.

[@alvaives9606]

Flysky video, thank you Joshua. You the man

[@quadfather504fpv9]

I have that one and did the 10 channel mod and that made it so much better, only thing it doesn't do is talk to you , and the fs-a8s receiver I had trouble with it loosing signal at only around 20 - 25 yards and I tried new antennas , longer antennas , even switched for another one , and still had the same problem , I ended up losing my quad over it ....

[@gavlarfpv7841]

Quad Father 504 FPV try the new x6b receiver and point antennas like mr. Steele🤙🏻

[@jasoncross6151]

Quad Father 504 FPV you can set up alerts via the internal beeper for battery voltage using the X6B RX

[@Just-A-Guy-Learning]

Gavlar Fpv 78 if you use the x6b swap to the higher dbi antennas. Like the ones that came on the ia6b. But the x6b has ipex connectors. I like the x6b and love my 14 channel mod on my fsi6

[@DashzRight]

You can say that again! its amazing, since I did the mod I don't see myself getting a more expensive radio for a long time.

[@KrotowX]

FS-8AS receiver is notorious. First revision was full of bugs which caused the signal loosing and destroyed/lost quads in result. Get FS-iA6B or X6B receivers - those both have functional diversity receiving, IBUS, telemetry and just works.

[@ReasonedRhetoric]

Josh if people are having trouble with the Eachine i6 for instance binding to other quads it doesn't have PPM output like the FS-i6 does. I think you can upgrade the software if you have the cable.

[@EBEFRANK]

Great video ...big help...just so you know...all of my channels were off substantially.....Thank you

[@mallle18]

you should use this remote more often since so many people have it! with 10 channel mod and voltage mod etc its a great remote.

[@Just-A-Guy-Learning]

Just use cli and you dont need to touch the trims or endpoints on the transmitter. rxrange 0 (low point) (high point) If your low number is 1005 and your high end points is say 2115. Then it would be rxrange 0 1005 2115 rxrange 1 1005 2115 rxrange 2 1005 2115 rxrange 3 1005 2115 Enter after each line and save. All endpoints are now 1000 middle 1500 and high point is 2000. If your numbers are different for each channel use those numbers accordingly.

[@smcclure3545]

KNUCKLEUP FPV Doesn't this have a negative affect stemming from the size of the packet/frame size?

[@Just-A-Guy-Learning]

S McClure No.

[@JoshuaBardwell]

This reduces the resolution of your control channels though. Much better to use the transmitter. Also, if you set the transmitter correctly, then you never have to adjust subsequent models (as long as you are using serial receivers).

[@Just-A-Guy-Learning]

Joshua Bardwell this is flysky. Trims move endpoints and not just center. Moving channel mapping in cli does nothing to the resolution brother. Its an equal amount of steps from end to end with the same amount of travel. You can use those little tick marks and check this if you want.

[@ZeroFPV]

There is also a mod and custom firmware to use this radio with FrSky receivers. Also works with the TGY Evolution.

[@MrSerdarcik]

zero problem ı love my flysky

[@jasoncross6151]

Always said Flysky would make a killing selling upgraded gimbals for the FS-i6, loads of people have this TX and with the 10 channel MOD and a antenna upgrade is super functional. Come on Flysky or anyone else....gap in the market....

[@michaelwilkes0]

I always add a little deadband for the jitter in my thumbs.

[@chrisb8424]

Super informative. Thanks for always sharing info.

[@krakenking1597]

thanks Joshua! love your channel.

[@thebridgeninja]

Thank you for the flysky love!

[@pilotgalau4614]

Thanks Joshua....nice

[@juliancolorado9232]

thanks men, excelent video

[@DashzRight]

Thanks for this video Josh!!!

[@dariodalcin5177]

didn't ok know why it was letting me adjust only one endpoint, this helped

[@krul23]

thanks for the video! 😊 this seems to be the fix im looking for😊

[@rogue-tr]

Hey don't you already have a vid showing endpoint adjustment on the taranis? It was quite old but saved me a heap of stuffing around when I got the Q X7. I've never had to adjust the FS-I6 except to facilitate receiver failsafe settings, i doubt it has anything to do with ibus but that's all I use.

[@justinphomarramos931]

Flysky forever

[@zibobman]

I have a prob with this radio, I can’t enter the menu anymore to calibrate the sticks, even if I put the sticks to the left and turn on the radio, it will stay on the main screen.., Any ideas???

[@josephbonnici7066]

Really really good video , thanks for the help 😊🖒🖒

[@rudra9117]

Thank you so much sir

[@AlexCastignani]

josh thanks very helpful tip!!!! ciao from italia!!!

[@rustygolfer3475]

Try the Evolution. I have more expensive radios but keep going back to it. My Fs-8s works fine on babyhawk. Never had a failsafe with Fs-A8S OR IA6C. Use IBUS for sure.

[@JoshuaBardwell]

I don't like the gamepad style of the Evolution.

[@rustygolfer3475]

Understandable. For people that grew up with a Playstation controller it is awesome. And $75, so easy to replace. Although I have had one for 6 months and just throw it in a bag, it is still perfect.

[@grumpydude1598]

i got a friend using the turnigy i10( iknow not the best but thats what he got) we cant calibrate endpoints bc its in multicopter mode, when we go to plane mode we can do it, but after we go back to multicopter it resets somehow, very frustrating

[@ravindersembi3955]

thanks JB helped me out!

[@jassofrank]

Hello I have the furibee f180 I replace the motors and now the fc I am using spf3 and the flysky with the fs ia6 receiver the transmiter dosent comunicate to the quad what are the ports inputs I try almost every thing now pleas help

[@GrumlyFPV]

I fly not so bad with a i6X + X6b I don't have more failsafes than my friends with their Taranis. I always loose video before radio and the form factor of the X9D or Q-X7 is way too big.

[@SubratRed]

Could you help me. Using pixhawk and Ublox gps 1400KV and 3S 11.1V. My drone is getting tilted and moving towards South West direction. The reaction is so fast that as soon as I take off it goes and hits to my wall and breaks the props. Any guidance to make it stable and fly vertically atleast. Used a lot of upper and right trims not working. Using Flysky i6 Mode2. Everything is ready from my end still first flight is pending. Thanks a lot

[@zero00419]

I got this same radio. And it works great with the flysky receiver in my Quad. But I try to bind it to my Radiomaster and it binds but when I Goto betaflight it doesn't work.. Any ideas

[@CrazyQuadBrothersP3]

"Joshua from the future!"👍🏻

[@yazon71]

Thank you Joshua, but can you please explain what max and min endpoints values should I set when my max throttle is ~1980 and min is ~1030? Should I anyway set max 2000 and min 1000 on the FS-i6 transmitter regardless of my measured max and min throttle? Thank you in advance.

[@JoshuaBardwell]

You should always adjust the transmitter so that betaflight sees 1000 to 2000 if possible.

[@machinedred]

How do I swop right stick elevator and left stick rudder over ?!?

[@casparharte]

Yaw is effecting the throttle too much. What can i do? This might just be my level of control on the gimbals.

[@K1QS_Radio]

thank you for the info. I haven't seen this discussed anywhere else. Is there an adjustment to leave the backlight on the FS-I6 on longer. Mine shuts down way to fast.

[@Dheerajkumarjha2]

My flysky FS I6 throttle stick start point is middle so I want to start point is down to up side pls. Reply ??

[@TDHobbies]

You have another video using the Taranis that shows how you can select receiver 00 to allow one model setting to control all of your similar quad copters. My question is. If using the one quad model option, will all the models be centered on Betaflight? Thanks, I am going to check my models right now.

[@JoshuaBardwell]

Yes, the subtrims and endpoints will be the same if you use a serial receiver and the same model in Taranis.

[@TDHobbies]

I just testing this with my Vortex 150 and the new 180 I just setup. I went from one model to the other (yes, I have 2 models set up) and I know for sure the 150 had yaw drift. All I did was set up the 180, then go into the 150 settings on the radio, copied the changes, and when I plugged in the 150 to betaflight, that drift was gone. Amazing! Thanks for all your efforts. I would like to chat with you sometime, I have a few questions about the Taranis... I'm formerly JR, then spektrum. Thanks again!

[@1337flite]

Or just use iBus which (I'm pretty sure) magically sets the endpoints correctly without human intervention. The only time I ever used SBUS on my i6x was with an Omnibus FC which had inversion on one of the UARTs and I needed all my UARTs.

[@audiogek]

That's what I thought. Though I just started doing fast righthand rolls and noticed that they were much faster than the easier lefthand rolls I'm used to. Checked in betaflight and was baffled to see the endpoint at 1100. Now I check really everything after every (re-)build

[@JoshuaBardwell]

I'm not sure how iBus could automatically set the endpoints. That would be surprising if it were true.

[@tehllama42]

I'm curious as well - mine were set up really nicely out of the box, and seem to be on point... but I assumed I was simply lucky, or too new to know the difference. Follow up video FTW

[@yonallb]

I don't think it sets endpoints automatically (how would it?), but it does hold the midpoint a lot better than SBUS. Less wander.

[@aaronzerbin8718]

Can you adjust the throttle end points to include reverse?

[@off-timer5149]

Endpoints start on 4:08 you are welcome

[@richardt1]

I have temporarily reduced the power settings in the throttle curve menu selection to 0,10,31,45,60. Should the endpoints still be adjusted for 1000-2000 or will this not be valid with the change to the throttle curve?

[@JoshuaBardwell]

if you have reduced the throttle curve in the transmitter then you don't need it to hit 1000 int he receiver tab.

[@patrickcol]

I guess you've tried the Turnigy Evolution? To me it feels very solid for a budget radio and has that unique form factor; but you're not a fan?

[@JoshuaBardwell]

I don't like the gamepad style controller.

[@tehllama42]

I have to agree with Joshua - the form factor is perfect if you want a console game controller to run on thumbs. Even more awesome with the wide lillypad stick tops.... but if you fly pinch, it's far less comfortable. Therefore, I run an i6x as a pinch flyer, but my friends who fly thumbs all love their Evos

[@zeebeefpv2273]

Joshua, I recently have been seeing my (FrSky Taranis X9DPlus) stick centers at 1517, rather than 1500 in BetaFlight ... What might be causing this? I haven't done any trimming with buttons, I haven't done any FC stick commands to set trim, nor have I touched the subtrim menus on my radio... Just curious if this will cause problems or go away or do I need to take action!?!

[@JoshuaBardwell]

If the sticks repeatedly fail to re-center correctly it could mean your gimbals are wearing out. This is more likely if you have the old style PT1 gimbals vs. the new M9 gimbals.

[@RCFlyer85]

10 ch Mod FTW!!!

[@amiyakumarmahanta4877]

@joshua i still have uneven responses..... If i yaw ri8 it goes linearly....but if i yaw left it shows 100% when i turn my yaw left a little bit..... Kindly help me with this....

[@JoshuaBardwell]

Try this: kzbin.info/www/bejne/fJytg5agqN94mpo

[@thebestojf7160]

Will it be the same with a airplane

[@rl2109]

Thanks for the info!

[@knightwolf8877]

I have the i6x and am having issues with stick right up the top in either flying or sim where it gitters, causing crashes. please help

[@buzz3890]

Joshua Bardwell Are you ready for Hurricane Harvey? I am in Austin and people are blowing up the grocery stores lol. We are just supposed to get some major rain but you should be getting hit with some floods :( Please be safe this weekend. Btw I just found a tbs unify pro HV used for $15 and I cant wait till it gets here. Your the Best!

[@JoshuaBardwell]

I'm not in Texas.

[@buzz3890]

Now I feel stupid. lol Any ways, love the videos.

[@sklobi]

Hello sir, I have a question... I just received new motors and I'm adding them to an existing build. Finished soldering new motors on and upon arming, motors spin up CRAZY. Do I have to go into betaflight and do anything?? I figured since the board was already set up, I wouldn't have to connect to computer?? I wired the motor the same way last motors were wired. I did switch from 1104 6500kv to 1105 7500kv if that matters. Thank you for your time

[@JoshuaBardwell]

If all you did was change the motors, then I don't know why they are spinning. So you must have done something other than just change the motors.

[@sklobi]

Joshua Bardwell I think I went thru adjusting end points like in this video.... I'll just go home and plug it in. I need to make sure motor direction is correct also. I hope is easily fixed. Maybe I'll just make a new model and rebind it.

[@jamiehill9578]

I've calibrating the sticks but now on the high end it won't go past 1980 , what's causing this

[@JoshuaBardwell]

Use the rxrange method as described in this video kzbin.info/www/bejne/Z5LdnWScbdZ9bpY&ab_channel=JoshuaBardwell

[@Bethethird]

thanks allot!!!

[@frankie44193]

Im still using this radio since starting a year ago.Using Ibus, i have never ever had to set endpoints. Only once i tried sbus and had to set every end point and trim. And it felt shit

[@MushypeasDMc]

Thank you very helpful

[@JoshCEarlharbo]

You mention plugging in your battery before making adjustments. Is this really necessary? I was able to adjust endpoints and subtrims without plugging in battery (just plugging into Betaflight).

[@JoshuaBardwell]

Not all FC power the receiver when plugged in to USB. Yours does, in which case you don't need to plug in to adjust these settings.

[@JoshCEarlharbo]

I hadn't considered other setups. Thanks for responding. I enjoy your stuff.

[@norbertwenkel9139]

Joshua why not using the rxrange commands for channel 1 to 4. Regards out of Germany

[@JoshuaBardwell]

Because it reduces the resolution of the channel. Always better to adjust endpoints in the TX if possible. Also, n00bs have a hard time figuring out how to use rxrange.

[@norbertwenkel9139]

Joshua Bardwell: Thanks Joshua, just a quick one, do I even reduce resolution setting (at my Taranis) endpoint to 125 % or do I mess something up?

[@clemsamuels1067]

I’m wondering how to connect to a computer program, as you did.

[@duyhayho7011]

Thank u

[@glenmccall4571]

i use libre pilot do you have something for that

[@fpvarborist7436]

What would I have to do if my radio to FC only gets about about 1000 to 1904 at full trim. Do I set max throttle to 1904 ish then just a normal ESC calibration

[@JoshuaBardwell]

Use rxrange to change the expected endpoints in cleanflight/betaflight.