Ford F-150 Radio / Stereo Not Working, Clock Blinking / Flashing - 2010 & Up- DIY Fix

🎦 Watch this video on diagnosing click flashing/ radio not working
• Ford F-150 Clock Blink...
🎦 Watch this video if you want to remove the radio:
• Blend Door Actuator Re...
❗️If you find this video helpful, I would appreciate a $uper Thanks that can be found below the video. Thank you!
💰Save money on other Ford F150 maintenance and repairs :
How To Check The Transmission Fluid On Ford F-150 With Aftermarket Dipstick
• How To Check The Trans...
Ford F-150 6.5 ft. Bed Removal on SuperCrew Cab - Easy Step-By-Step
• Ford F-150 6.5 ft. Bed...
Ford F 150 Spare Tire, Jack, and Tools Location& Removal Drop Spare Tire on Ford F-150
• Ford F -150 Spare Tire...
Any Ford F-150 Tailgate Removal - No Tools Needed
• Any Ford F-150 Tailgat...
Ford F 150 Fuel Gauge Problem: How To Know If It Is The Cluster Or Something Else
• Ford F 150 Fuel Gauge ...
The most effective way to find a leak in Ford F-150
• Ford F-150 cab water leak
How to relearn and reset TPMS (tire pressure monitor sensor) light
• How to relearn and res...
Ford F-150 Transmission Problem? Might be an Easy Dry Shaft Fix
• Ford F-150 Transmissio...
How to find your security keyless entry keypad code on Ford F150
• How to find your secur...
How to Remove Ford F150 Fronts Seats
• How To Remove Ford F15...
How to unlatch rear seat back on 2009-20014 Ford F-150
• How to fold down rear ...
How Remove Ford F150 Inside Door Panel
• Ford F150 Interior Doo...
The Removal and Installation of Door Lock Actuator, common failure on F150
• Replacement of door lo...
How to Replace Blinker Bulb on Ford F-150 2009-2014
• How to Change Turn Sig...
Review, installation, and testing of GTR Lighting ULTRA 2 LED: H13 Headlights for 2009-2014 Ford F150
• Review, installation, ...
Review and installation of LASFIT Pro series Custom Design LED headlights for 2009-2014 Ford F150
• Review and installatio...
Ford F150 Gas Cap won’t stay closed? Permanent Fix!
• Ford F150 Gas Cap won’...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the
future.
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.

[@danielvogt5795]

I’m reporting this video as witchcraft bc there’s no way sticking a circuit board in the oven just fixed my radio!

[@jamesmilamjr7025]

You don’t have to do anything but disassemble it down to the chip and put it in the oven on 375 degrees for 6-7 minutes. I just done it last night. It REALLY DOES WORK!!

[@rayalcodray8248]

Did it today - and it worked!!! Thank you. Be mindful that solder melts at 370 degrees. Your oven needs to reach that temp. When removing don’t shake or dip because solder can drip off or run. Good luck!

[@The_Active_Region]

Resolder by hand Q201. It is a 8 pin IC or transistor pack. Heating in the oven trying to reflow lead free solder without flux on the board is pointless. It may work but not for long. You also risk further damage to the board and or connectors. The only way to reflow the board properly is to get it hot enough that it may melt or deform those connectors. The connectors are most likely added on after the main board is produced in another machine that wave solders them on. Also there is components on the the bottom side of the board that can fall off during the reflow if it is moved before cooled.

[@knievelhotmail]

I was an elec tech for years. The cooling part of this repair isnt that important. If youve reflowed the solder as described, its fixed for a long time. The problem is caused by thousands of hot/cold cycles finally causing a microscopic crack in a soldered joint. Seen it a million times.

[@boogiemasterofsome]

I tried it but it did not work for me. Can't find one for less than $200 on eBay.. looks like I'm out a stereo.

[@frh290-3]

I just re-flowed mine with a solder iron and good flux. It’s working perfectly again. I don’t understand how the oven method will do anything to solder that has a melting temp between 500deg and 800deg? Glad it seems to be working and this isn’t the first I’ve heard of it but idk.

[@PacoClan05]

Amazed. Just like others I was doubting it, but followed your directions and now my system is working.. Thank you!

[@garybeitel8212]

Didn't work!!

[@luisterrazas514]

worked for me! this was my last attempt to fix it myself. just like everyone else watching this i was skeptical about putting something in the oven for 16 minutes. i had nothing to lose since it didn’t work anymore. thank you!! time will tell how long it will work.

[@markanderton8260]

I did exactly what he said....outstanding. Put it all back together, and it is working perfectly...

[@nixonmontan7373]

I fully understood the concept of putting it in the oven, as the solder points do soften and settle back into place. This fix had not come to my mind, but when I saw the video I followed the simple instructions and it fixed the problem of the radio popping and going silent, as well as clock flashing intermittently. This radio has a new lease on life now. Thank you.

[@furbee28]

I was sceptical but it worked! Thank you

[@ddub2023]

followed your video, worked perfect! thank you

[@briankillen6545]

Worked perfectly, I followed exactly as you said!

[@assult537]

I tried this method, and it worked!! Thanks a lot!

[@samc8272]

Well…. I did it and it worked. Awesome thank you Sir. I gotta be honest, when you said put it in the over I was like Oh Boy here we go haha. I’m in the truck now rocking out

[@guidrydale]

Absolutely worked my man thank you for sharing

[@Jacob-Terry]

Great video! Very helpful thank you!

[@genes294]

This worked on our 2014 Ford F-150! THANK YOU !!!!!!!!!!!!!!!!!!!!!!