Ford Fusion turn signal fix

[@matthayden8078]

You are a life saver!!!! Thank you!

[@neeldgar5198]

Yes, do you still need the step-by-step?

[@YeeiPlay]

I need help, I have same issue but can you post a video tutorial step by step?

[@matthayden8078]

Thank you for the help. I could essentially tuck the old housing unit in somewhere, and just install a new housing that is getting power from the relay, and ground it to complete the circuit? I guess I am just confused because I can see the power go into your new bulb housing from the relay, but, I do not see any ground connections coming out of the bulb housing to complete the circuit. Thank you!

[@neeldgar5198]

Yes I tapped it under the dash. Now be careful because there are two wires coming out with the same color. They are two separate gauge wires. Match up the gauge in the back and then use a test light to verify.

[@Jakesuttill]

I have the exact same problem same front turn signal. Would you happen to know the color of the wire you spliced into under the dash to get the signal to the relay. And why can’t you just go straight to the bulb cutting the wires and still adding the inline dummy bulb elsewhere to keep the dash code clear . 12 volts is 12 volts. Why the relay.

[@alainchevalier6088]

O.K I got the problem (ford fusion 2006) with the back turn signal, Seem the wire for back turn signal be cut or stupid (smart junction box) don't do is job. Did you know the wire colour of the back turn signal wire ? If you can make it work for the front probably it will work for the rear if the wire are not cut anywhere, but both the wire will be surprising. The hazard work in fronyt but not in rear. Brakes, light work fine just the blinker circuit seem affected. What miss in the video are which number of the relay goes to where ? The number 30 is the power supply but the othe numbers goes to which wires ?

[@bethanyt4412]

do you still have those step by step intructions. I know it been a year ago Garret Neeld, but I am having the same problem you did and I don't wan to give Ford any money either. never did electric stuff. and trying to find some one to do the work is Crazy too.

[@GtrsNCars]

Couple questions. Why would this wiring make the front signal come on with the brake lights if it's tied in to the rear turn signal? And how did you wire in to the smart panel under the dash? Did you just stuff a wire in next to a fuse? The problem I'm having is the front running lights never turn off and the car acts as if the front bulbs are out so it blinks faster than normal when you signal. Weird.

[@joerice6872]

Clint Schoenthaler The rear signal and brake light are the same bulb and wire.

[@ripperroaredloaded3478]

I have an issue similar to this, 2006 fusion. My issue is I got the car without any turn signal bulbs in the front, I went to lordco and got new bulbs, after installation they just won’t turn off, they stay on solid, even with vehicle off and doors locked. Any advice?

[@garretneeld4321]

I got comments on wiring this up, did you get the wiring figured out ?

[@gunner00745cal]

Hi i had ford fusion 2007 is that applicable to my car. my has a right side turn signal issue in front. You may help me how to do a wiring?

[@Hoosier_]

Could you just tap into the rear signal and run that wire to the front bulb and just run the negative side of the bulb to a ground? Or does it need/require the relay?

[@neeldgar5198]

Off the top of my head I don't remember why I took that approach. Sounds like you could do that.

[@mattwevans]

You can’t do it like that because the brake light and turn signal use the same wire

[@timmythurman8801]

Which pins did you use for what on the relay

[@neeldgar5198]

Send a picture of your relay. There is a coil and N.O & N.C contacts.

[@timmythurman8801]

How do I do that?

[@ThrottleStopRacing]

where did you pick up the lr turn signal signal?

[@drewmiller8508]

Which part of the smart junction box controls the right turn signal (front)

[@neeldgar5198]

I would check but have sold the car. You'll have to get a manual and look up the wiring.

[@neeldgar5198]

That red wire you see tied to chassis ground is my ground. I didn't have a black wire to represent ground to be proper. Sorry for confusion.

[@neeldgar5198]

Sorry, yes it's grounded. This was taken on my new phone so I didn't get into a lot of detail because I was trying to keep my new S6 clean that didn't have any protection yet.

[@matthayden8078]

Is there a shortcut for the back turn signal, or did you run a wire the length of the car?

[@garretneeld4321]

matt hayden I tied into the wire right under the dash.

[@neeldgar5198]

Also I didn't mention you have to cut the existing wire to the front signal and wire it to an old light socket with bulb or a resistor and ground or your dash will show a fault. That failed circuit still wants to see that something is there.

[@joshflamez218]

did you had a fire in that Eng compartment i see fire extinguisher dust

[@neeldgar5198]

You ground the wire coming out of the bulb connector to chassis ground.

[@GtrsNCars]

Do your front turn signals come on when you hit the brakes?

[@garretneeld4321]

Yes it does. After I realized this my daughter took the car so I never got a chance to correct it

[@garretneeld4321]

Yes

[@GtrsNCars]

I was afraid of that. How do you correct it?

[@garretneeld4321]

I will look at it when my daughter brings the car by. She has been willing to live with it and took off with the car since I did it.

[@tonyaharrington2605]

Curious if you have every posted step by step instructions. Having the actual same problem and not interested in paying Ford any money.

[@maciaswork5384]

Hello, I would like to know if you ever did a step by step on this?

[@garretneeld4321]

what part are you struggling with ?

[@GtrsNCars]

I suppose it’s still better than paying hundreds for a new one. LKQ wants 50 bucks for a used one here. And there’s no guarantee it will work.

[@garretneeld4321]

I was asked why the front turn signal also acts like a brake light as well. Tying into this circuit will do that. I never fixed that problem because my daughter was in a damn hurry to take the car. It wasn't a perfect solution just a cheap one.

[@garretneeld4321]

she is still driving it this way today. Not perfect but much safer than no signal at all.

[@GtrsNCars]

I have a similar situation only the daughter left and the car is still here...lol

[@DanielDiaz-me9po]

any chance of the step by step guide

[@neeldgar5198]

Do not try and tie this new circuit power to the circuit that failed and back feed it !

[@neeldgar5198]

Yes you could do that.

[@garretneeld4321]

sorry I never get on here, I don't intentionally ignore people I just work 12 hrs a day 6 days a week. Damn people eat to much candy lol. I will have to do a step by step soon if you guys still want it.

[@chriscosten80]

any step by step is grateful. im going to do this same thing this week. im having a problem tieing into the back wire. when i do its working the turn signal and the brake light upfront. ive tried both wires

[@melissa-nt5yp]

Yes please. Step by step instructions would be great.

[@garretneeld4321]

melissa I will post a step by step this weekend.

[@iancameron1662]

Did you ever post a step by step on the turn signal problems..thanks